Classic Exhibits visionary DESIGNS MOD-1298 User manual

© 2016
www.classicexhibits.com
Order #XXXXX - MOD-1298 Pedestal Assembly
Floor
Infill
Infill
Infill
Door
Counter Top
Counter
Top
Item
12
13
14
14A
15
16
17
18
19
Description
38” RR91 Vertical Extrusion
38” RR91 Vertical Extrusion w/Door Stop
43” RR91 Vertical Extrusion
Plate for Counter Connection
38” RR91 Vertical Extrusion w/Door Hinges
20” Z46 Horizontal Extrusion
8.5” Z46 Horizontal Extrusion
20” Z45 Horizontal Extrusion
8.5” Z45 Horizontal Extrusion
Internal Shelf Support
Quantity
1
1
1
1
1
2
2
2
2
4
12
13
14
15
16
17
16
17
18
18
19
19
Steps:
1) Connect horizontals [16 & 17] between verticals resting on top of stoppers
at approximately 4” up from floor to bottom of metal.
2) Set floor in place on top of lip of horizontal extrusions.
3) Place infills in place as shown.
4) Connect horizontals [18 & 19] between verticals and atop inserts as shown.
5) Velcro shelf supports to inside of pedestal, then set internal shelf atop supports.
6) Hang door on hinges as shown in detail.
7) Place large counter top on top of assembled base.
8) Attach connector plate [14A] to vertical [14] then connect smaller counter to [14A].
9) Attach graphic to front of pedestal with standoffs as shown in detail.
Extrusions 10 and 11
have a lip for the
floor to rest
upon.
14A
Internal Shelf
Slide pin into
hinge attached to
Round Vertical.
Slide Door hinge
atop pin.
Door
Hinge
Pin
Hinge
Door Attachment
Shelf
Support
4”
Stopper at 4”
Graphic
Cap
Standoff
Barrel
Slide connector on back of
standoff barrels into groove
of extrusion and twist to
secure in place. Secure graphic
to standoffs using screw caps.
Graphic Attachment

© 2016
www.classicexhibits.com
Order #XXXXX - General Information
DO NOT USE POWER TOOLS
ALL CONNECTIONS MUST
BE TIGHTLY SECURED
Part Identification - Numbering
Spline Connection Base Plate & Extrusion Connection
General Setup Instructions
- Read entire setup instruction manual prior to
unpacking parts and pieces.
- The setup instructions are created specifically
for this configuration.
- Setup instructions are laid out sequentially in
steps, including exploded views with detailed
explanation for assembly.
WARNING
Cleaning & Packing
- For Cleaning Metal, Plex, & Laminate Parts:
Use a MILD NON-ABRASIVE cleanser and
soft cloth/paper towel to clean all surfaces.
- Keep exhibit components away from heat
and prolonged sun exposure.
Heat and UV exposure will warp and
fade components.
- Retain all provided Packing Materials.
All provided packing materials are for
ease of repacking & component protection.
Disassembly
- For loss prevention, tighten all setscrews
and locks during disassembly
7A
Hex Tool - Essential for Assembly
Extrusion & Lock Connection Engaged Lock
LADDERS OR LIFTS
MAY BE REQUIRED

© 2016
www.classicexhibits.com
Order #XXXXX - Packing Instructions - Case 1 of 1
Vertical Extrusions
Internal Shelf
and Floor
Door
Small Counter
Counter Top Infills
Top View
Level 5Level 4Level 3Level 1 Level 2
15 12 13 14
16(2) 18(2)
17,17,19,19
Setup Hardware