Classic Exhibits SACAGAWEA DESIGNS VK-1232 User manual

www.classicexhibits.com
Step 1
Page 1 of 5
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - Sacagawea - VK-1232 - General Layout
10’
10’ Plan View

www.classicexhibits.com
Step 2
Page 2 of 5
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - Sacagawea - General Information
Using You Set-up Instructions:
The Visionary Designs Set-up Instructions for Sacagawea displays are created
specifically for your configuration. They are laid out sequentially, including an
exploded view of the entire display and a logical series of detailed steps for
assembly. We encourage you to study the instructions before attempting to
assemble your exhibit.
THIS IS VERY IMPORTANT!
Each page reminds you to tighten the setscrews after disassembling your
exhibit to prevent loss of the locks and setscrews (see below in red).
Cleaning & Packing Your Display:
1) Use care when cleaning aluminum extrusions or acrylic inserts. Use only
non-abrasive cleaners.
2) When cleaning laminate inserts or counter tops, use mild cleansers and
a soft material such as cotton.
3) Keep all display components away from extreme heat and long exposure
to sunlight to avoid warping and fading.
4) Retain all packing materials. It will make re-packing much easier and will
reduce the likelihood of shipping damage.
Hex Key Tool Typical Connection Typical Connection
Most visionary design exhibits can
be assembled with the supplied Hex
Key Tool. Occasionally, a flat head
screwdriver may be required. Detail A: Most horizontal extrusion connections have a patented expandable lock. This lock inserts into
the groove of an opposing extrusion. Tightening the lock with the Hex Key Tool expands the lock and creates
a strong positive connection.
Numbered
Label
Detail B: Each extrusion contains a numbered label that
corresponds to set-up instructions. The label is located
within a groove of the extrusion (when possible). Visionary
Design labels contain Black numbers unless otherwise
specified.
Horizontal Connection
Detail C: A rectangular connection bar with plastic
T Knobs is inserted between two horizontal extrusions
joined end-to-end. Turn the knobs clockwise to tighten.
Base Plate Connection Vertical Connection Corner Connection
Detail D: Attach vertical extrusions to base
plates with supplied bolts inserted through
the hole in the plate. Be careful not to strip
the thread.
Detail E: A square connection bar with
plastic T Knobs is inserted between two
vertical extrusions joined end-to-end. Turn
the knobs clockwise to tighten.
Detail F: Plastic Star Knobs are
used to tighten locks where
horizontal extrusions connect with
vertical extrusions. Turn the knobs
clockwise to tighten. Turn counter-
clockwise to loosen, but do not
remove knob.
Do Not Overtighten.
Do Not Overtighten.
Do Not Overtighten.

www.classicexhibits.com
Step 1
Page 1 of 5
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - Sacagawea - Backwall Assembly
indicates
location of connection
lock with knob.
Note: Slide connection
bar between extrusions and
tighten knobs to secure.
Connection Bar
a
Item
1
2a/2b
3a/3b
4a/4b
5a/5b
Description
Base Plate
42” Vertical Extrusion
42” Vertical Extrusion
45” Horizontal Extrusion
45” Horizontal Extrusion
Qty.
2
1/1
1/1
1/1
1/1
Steps:
1) Attach base plates [1] to lower verticals [2a,3a] with bolts.
2) Connect upper verticals [2b,3b] to lower verticals [2a,3a] with connection bars [b].
3) Connect horizontals [4a,4b] and [5a,5b] with connection bars [a].
4) Connect vertical assemblies [2a/2b,3a/3b] with horizontal assemblies [4a/4b,5a/5b]
as shown.
5) Attach graphics to velcro on back side of frame.
Turn Knob Clockwise
to Tighten Lock
indicates location of
knobs on BACKSIDE of unit.
Do not over tighten Knobs
Knob
Knob
Horizontal Placement
Stopper
Set upper horizontal
bar atop stopper where
indicated on verticals
Front View
Back View
a
b
b
1
1
2a
2b
3a
3b
4a
4b
5a
5b
Velcro:
Back/Bottom Edge
Velcro:
Back/Top Edge
Attach graphic
to velcro on back
of frame
Canopy
Mount

www.classicexhibits.com
Step 2
Page 2 of 5
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - Sacagawea -
Slide A10 Clamp
into groove
of square extrusion.
When desired location
is found, tighten
set screw to secure.
Set-
Screw
A10
Tighten black plastic
set screw to secure
Wing in place.
Black Plastic
Knob
Wing Attachment
Keep A10 clamps
attached to verticals
Graphic
Screw
Cap
Standoff
Barrel
Slide connector on back of standoff
barrel into groove of extrusion
and twist to secure in place. Secure graphic
to standoffs using screw cap.
Graphic Attachment
Note: Curved extrusion
[10] and horizontal [11]
stay assembled for
shipping and packing.
10
10a
11
Screw
11a
Counter Top Attachment
Insert screws located on underside
of counter into holes on flange plate
and secure with wing nuts.
Wing Nut
Item
10
10a
11
11a
Description
30.2” Curved Extrusion
Leg Support
12.184”w Horizontal Extrusion
Flange Plate
Qty.
1
1
1
1
Steps:
1) Attach lights as indicated.
2) Attach assembled counter support [10/11] to vertical where indicated.
3) Attach support leg [10a] to counter support [10/11].
4) Attach flange plate [11a] to top of curved extrusion [10] as shown.
5) Attach counter top to support, see counter top attachment detail.
6) Attach wings to A10 clamps as shown.
7) Attach round sign to backwall frame as indicated.
8) Attach monitor mount to backwall, see monitor mount
attachment detail.
Monitor Mount
Attachment
V4 Connectors
Attach monitor mount back plate
to connectors using screws provided.
*
Counter, Wing and Sign Attachment

www.classicexhibits.com
Step 3
Page 3 of 5
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - Sacagawea -
Canopy Assembly
Connections are made by holding the button
down and sliding the red tube into opposing
tube until the connection is made. To disassemble
push button and pull or twist extrusions apart.
Push-Button
Push-Button
66
6
6
Numbered Label
Using Your Setup Instructions
The Aero Overhead Sign Setup Instructions are created specically for your conguration. They include an
exploded view of the frame which is sequentially numbered. We encourage you to study the instructions
before attempting to assemble your exhibit.
Connections are kept very simple: no tools. Everything assembles with push-button
connectors and pre-connected horizontal sections.
Cleaning and Packing Your Display
1) Use care when cleaning aluminum extrusion or acrylic inserts. Use only non-abrasive cleaners.
2) Retain all packing material. It will make re-packing much easier and will reduce the likelihood
of shipping damage.
Steps:
1) Connect canopy pieces together as shown.
2) Apply pillow case graphic to assembled canopy
A
A
B
B
D
D
CC
Push-Button
Push button then rotate
for packing purposes

www.classicexhibits.com
Step 4
Page 4 of 5
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx - Sacagawea - LTK-1001 - Pedestal Assembly
Setup Instructions:
A) Use standoff screws to secure the front panel with
door and back panel of the pedestal to the side panels.
B) After assembling front, back, and side panels,
slide floor into the bottom of the pedestal. The
floor will sit on pins on the inside of the side panels.
C) After floor is in place, velcro shelf supports in corners, and
place shelf on top of supports.
D) Place counter top on top of assembled base.
Standoff
Screw
Front Panel
with Door
Floor
Velcro Shelf
Supports to
corners.
Shelf
Place the oval counter
top of the pedestal base.

www.classicexhibits.com
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx -
Case Packing Instruction - Case 1 of 2
Top View
Wing Panels
Level 1 Level 2 Level 3 Level 4
Canopy Pieces
Setup Hardware
Halogen LightHalogen Light
Graphics
Counter
Top
Base
Plates
Backwall
Counter
Support
10a
A
B
Extr. #4a&4b and 5a&5b
Extrusions #3a&3b
Extrusions #2a&2b

www.classicexhibits.com
866.652.2100
© 2012
WHEN DISASSEMBLING ALUMINUM EXTRUSION, TIGHTEN ALL
SETSCREWS AND LOCKS TO PREVENT LOSS DURING SHIPPING
Order #xxxxx -
Case Packing Instruction - Case 2 of 2
Counter Top (2) Side Panels Back PanelFloor and Internal Shelf
Level 2Level 1 Level 3 Level 4 Level 5
Front Panel w/ Door
Top View
(2) Pedestal Components