Clean Water Living Water VORTEXer User manual

USER GUIDE
EN
PANTONE305C
CLEAN
WATER
DENMARK
DENMARK
SILVER MEDAL
SALON INTERNATIONAL
DES INVENTIONS
GENÈVE 2018
www.clean-water.com
Living Water VORTEXèr

CONGRATULATIONS ON YOUR NEW LIVING WATER VORTEXèr!
Please read these instructions thoroughly to make sure you can use your Vortexèr for
many years and have the most benefit of it.
IN THE BOX
Jug with lid, USB cable.
Your new jug with lid, USB cable and this manual.
HOW TO HANDLE THE JUG
Before first use clean the jug and lid with a moistened soft cloth.
IMPORTANT! ALWAYS REMOVE THE LID WHEN:
1. FILLING IT WITH WATER.
2. PUTTING THE JUG IN A REFRIGERATOR.
1. Always take the lid off the jug before you fill it with water as there
are electrical components in the lid that MUST NOT get wet!
2. To vortex the water correctly always fill the jug to the mark
(see image 2).
3. Put the lid on with the red/grey USB cover pointing a little to the
right of the pouring spout (see image 1) and close it by rotating
it clockwise so the little knob on the lid-side is placed above the
vortexing symbol (see image 3).
4. Place the Vortexèr on a stable base before you start vortexing.
5. Push the button accordingly to “HOW TO START – STEP BY
STEP” (see next page).
6. Have fun watching the water being vortexed!
7. The water is ready when the vortexing ends and it settles.
Preferably wait for another 10 minutes. The peak water quality
is reached after 4 hours, when the hydrogen atoms have
stabilized. The water holds the energy for a long time, up to
months, but it is best to drink it within 1-2 days.
8. Rotate the lid counter clockwise so the little knob is placed
above the drop symbol (see image 4).
9. Pour your water, drink & enjoy!
Image 1
Image 2
USB
Image 3 Image 3 Image 4 Image 4

Right button with “tuning fork” symbol (3:20 minutes):
Programmed to get you started using the Vortexér.
Left Button with “few bubbles” symbol (3:20 minutes):
Everyday use with good quality tap water.
Middle button with “many bubbles” symbol (7:30 minutes):
By using this program the water will become more highly energized. For low
quality, bad tasting or heavily chlorinated water, run the program twice. Wait for
the vortex to end and settle, before pressing the button the second time.
THE FUNCTION BUTTONS ON THE LID
HOW TO START - STEP BY STEP
Week 1:
Use the “tuning fork” button I. Start with 1⁄2-1 glass of water on the first day.
If you do not feel any discomfort, drink 1-2 glasses for the rest of the week.
Week 2 and 3:
Keep using the “tuning fork” button I. Drink up to about 1 liter per 40 kilo body weight.
If needed you can prolong this period before you go to the next step.
After 3 weeks:
If you do not feel any discomfort, you are ready to use the “few bubbles” button II.
If you feel any discomfort – drink less of the vortexed water.
When the body gets used to the altered energy and quality of the vortexed water,
you may want to use the “many bubbles” button III to increase the energy in the water.
If this seems too strong, go back to the previous setting/drink less vortexed water.
Only run the “many bubbles” button III twice if you have very low quality water.
CARE AND CLEANING
Remove any lime scale residue with lemon or vinegar using a soft cloth.
Do not use any other type of cleaners or lubricants.
Do not immerse the lid in liquid or put in dishwasher – the electrical parts will be damaged!
Polish the propeller using a soft cloth if it becomes tarnished to maintain the antiseptic effect.
Once or twice a week you may want to place the lid on a lukewarm radiator over night.
This will remove any condensation which occurs as a result of temperature changes.
Place it with the propeller facing down.
CHARGING
If the internal light blinks when pushing any button and it does not start, it is time to recharge.
Please plug the cable into the lid under the red/grey USB cover on one end and into your USB
power adapter on the other end. One charge will provide about 50 vortexes using the few
bubbles button (top left button). Up to 8 hours fully charged. Slow charging prolongs battery
life.
To stop the vortex earlier/manually press any button once
I
II
III

TECHNICAL INFORMATION
• The jug contains 1.8 liters.
• The vortexing process runs for 3:20, 3:20 or 7:30 minutes at 39, 42 or 46 RPM.
• Both jug and lid are made of ECO-friendly Bio-Co-polyester, a new break-resistant plastic
(certified Ecozen Bio-Co-polyester, made from renewable materials using biomass, BPA &
phthalate free). It is approved for food and is resistant to vinegar (for cleaning).
For more details visit: www.clean-water.com
• The propeller and the bottom plug have a 30 micron coating of pure silver, to inhibit bacteria.
• Rechargeable Lithium battery. If the internal light blinks when pushing any button and it
does not start, it is time to recharge. Please plug a cable into the lid under the red/grey
USB cover on one end and into your USB power adapter on the other end. One charge
will provide about 50 vortexes using the few bubbles button II. While charging the LED in
the lid blinks (up to 8 hours).
When fully charged the LED is off. Thoroughly replace the USB cover again!
PANTONE305C
DENMARK
CLEAN
WATER
DENMARK
2 YEARS
WARRANTY
Disposing of this product correctly will help save valuable resources and prevent any potential negative ef-
fects on human health and the environment, which could otherwise arise from inappropriate waste handling.
WARRANTY, SERVICING & REPAIR
There is a 30 day return policy on the Vortexèr . If returned the Vortexèr must be completely
dry and in the original packaging. The seller will pay for return shipping, provided you request
a return label, which will be sent by mail.
The
Vortexèr is covered by a 2-year warranty on materials and construction. The Vortexèr
may only be used for vortexing of water. Normal wear and tear and damage due to misuse or
inadequate care and cleaning are not covered by the warranty. It is the user’s responsibility to
check that cables are intact and to inspect the parts for possible damage and wear.
Repairs must be performed by authorized technical personnel only. The
Vortexèr may not be
serviced or repaired by the user. In the event of malfunction, please return the defective parts
to your LIVING WATER VORTEX
èr dealer for repair.
IMPORTANT:
Remember to include the invoice/order confirmation number or a copy
of the receipt together with your phone number or email address.
SAVE YOUR USER GUIDE
It is also your guarantee certificate and is valid for 2 years
from the date of your invoice.
CLEAN
WATER
DENMARK
Clean Watercom ApS
Ansoevej 27 Vrads, DK-8654 Bryrup. EORI/vat 20005297. Contact: Tel: [phone]. E-mail: [e-mail]