Clevo 2200C User manual

Notice
The company reserves the right to revise this publication or to change its contents without notice.
Information contained herein is for reference only and does not constitute a commitment on the part
of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any
errors or inaccuracies that may appear in this publication nor are they in anyway responsible for
any loss or damage resulting from the use (or misuse) of this publication.
This publication and any accompanying software may not, in whole or in part, be reproduced, trans-
lated, transmitted or reduced to any machine readable form without prior consent from the vendor,
manufacturer or creators of this publication, except for copies kept by the user for backup purposes.
Brand and product names mentioned in this publication may or may not be copyrights and/or regis-
tered trademarks of their respective companies. They are mentioned for identification purposes only
and are not intended as an endorsement of that product or its manufacturer.
©March, 2001
Preliminary Version

Contents
Chapter 1: Introduction ........................... 1 - 1
System specifications (general) ...................1 - 2
Chapter 2: Chipset and
Mainboard information ............................ 2 - 1
CPU...............................................................2 - 1
Chipsets........................................................2 - 3
SiS630S ............................................................ 2 - 3
PCCardChipset- PCI1410 ............................. 2 - 11
Ports............................................................2 - 13
Mainboard....................................................2 - 14
Mainboardcomponentslist ............................... 2 - 14
Mainboardphoto .............................................. 2 - 15
Chapter 3: Disassembly.......................... 3 - 1
Sizechart forscrews andhex nuts: .................... 3 - 1
Disassembly steps .......................................3 - 2
StepstoremovetheCD-ROM/DVD-ROM: .......... 3 - 2
StepstoremovetheCPU:................................... 3 - 2
StepstoremovetheFDD:................................... 3 - 2
StepstoremovetheHDD:................................... 3 - 3
Stepstoremovetheinverterboard:..................... 3 - 3
StepstoremovetheLCDpanel:.......................... 3 - 3
Stepstoremovethemainboard:.......................... 3 - 4
Removal Procedures ....................................3 - 5

Removethebattery............................................. 3 - 5
Removethekeyboard......................................... 3 - 6
RemovetheHDDassembly ................................ 3 - 7
RemovetheCD-ROM\DVD-ROMassembly ......... 3 - 8
Removetheheatsink ......................................... 3 - 9
Applyingaheatsinkpad .................................... 3 - 9
RemovetheCPU .............................................. 3 - 10
ReinstalltheCPU ............................................. 3 - 10
Separatethenotebookbaseintwo ................... 3 - 11
RemovetheFDDassembly............................... 3 - 14
RemovetheCD-ROMtray ................................ 3 - 14
RemovetheFan ............................................... 3 - 14
Removethemainboardand
trayfrom thebottom case ................................. 3 - 15
Removethemainboard
fromthemainboardtray ................................... 3 - 16
The LCD Panel ...........................................3 - 17
RemovetheLCDpanelframe ........................... 3 - 17
RemoveLCDpanelfromtheLCDpanelcase.... 3 - 18
RemovetheLCDpanelfromthebracket ........... 3 - 20
AppendixA: Mechanical Drawings and
Parts Lists ................................................A - 1
2200C ...........................................................A - 1
BottomHalfassemblyandpartslist .....................A - 1
LCDpanel(12.1”)assemblyandpartslist...........A - 2
LCDpanel (13.1”, 15.3”)assembly and
partslist .............................................................A - 3

LCDpanel(14.1”)assemblyandpartslist...........A - 4
KeyboardandTouchpadassembly .....................A - 5
KeyboardandTouchpadassemblypartslist ........A - 6
FDDassemblyandpartslist ...............................A - 7
HDDassemblyandpartslist ...............................A - 8
CD-ROMassemblyandpartslist.........................A - 9
DVD-ROMassemblyandpartslist .................... A - 10
2700C .........................................................A - 11
Bottomhalfassemblyandpartslist ................... A- 11
LCDpanel (13.3”)assemblyandpartslist........ A - 12
LCDpanel(14.1”)assemblyandpartslist......... A - 13
KeyboardandTouchpadassembly ................... A - 14
KeyboardandTouchpadpartslist ..................... A - 15
FDDAssemblyandpartslist ............................. A - 16
HDDassemblyandpartslist ............................. A - 17
CD-ROMAssemblyandpartslist ...................... A - 18
DVD-ROMassemblyandpartslist .................... A - 19
Appendix B: Schematic Diagrams .........B - 1
Appendix C: Switch Settings ..................C - 1
ClockSettings(SW6)........................................ C - 1
PanelIDSettings(SW7) ................................... C - 2

Introduction
1 - 1
Chapter 1: Introduction
This manual covers information you will need to service or upgrade your Notebook Computer.
Information about operating the computer (e.g. getting started, etc...) is in the User’s Manual. Driver
Information is also found in the User’s Manual. The User’s Manual is shipped with the computer.
Operating Systems (Windows ME, Windows 2000, etc.) have their own manuals as do application
software. If you have any questions regarding those, please consult their user’s manual.
This manual is intended for service personnel who have completed sufficient training to
undertake maintenance and inspection of personal computers. It is organized to allow you to look up
basic information for servicing and/or upgrading components of the notebook computer. The follow-
ing information is covered.
– Specifications
– Chipset and Mainboard information
– Disassembly
– Mechanical drawings and Parts Lists
– SchematicDiagrams
– SwitchSettings

1 - 2
Service Manual
System specifications (general)
The main unit of the Model 2200C/2700C Notebook PC has the following components:
– Intel FC-PGA370 Pentium III with AGP technology-based mainboard, using the SiS630S
chipset solution supporting SDRAM with 0MB on-board DRAM, expandable to 32MB, 64MB,
96MB, 128MB, 192MB, 256MB, or 512MB using one or two expansion SODIMMs
– user-installed modules: CD-ROM or DVD or CD-RW ROM
– mainstorage (HDD) bay:principal HDD 2.5”12.7/9.5mm, supports PIOmode 4/ATA-33/66/
100 (Ultra DMA) and Master mode IDE.
– Userinterfaces
- one internal keyboard, 84 keys (depending on the language)
- one built-in touchpad
- one 1024x768 XGA Color TFT LCD with CCFT backlight, size 13.3” or 14.1”, supports
IDCT
– Power Solutions
- power bay: battery pack
- AC adapter

Introduction
1 - 3
CPU ( FC-PGA370 )
Intel Celeron-450 (1.6V)
Intel Celeron-500 (1.6V)
Intel Celeron-550 (1.6V)
Intel Pentium III-600 (1.65V)
Intel Pentium III-650 (1.65V)
Intel Pentium III-700 (1.65V)
Intel Pentium III-750 (1.65V)
Intel Pentium III-800 (1.65V)
Intel Pentium III-850 (1.65V)
Intel Pentium III-866 (1.65V)
Intel Pentium III-933 (1.65V)
Memory
L2 Cache (on die)
Celeron(.18) series 128KB
Pentium III series 256KB
On board RAM 0MB
Upgradable to 512MB
TouchPad
built-i n x 1
interface PS/2
Keyboard
Keys 84
Fn key support YES
Integrated numeric keypad YES
Inverted “T” layout cursor keys YES
HDD
Easy change module 6GB or up
Drive size 2.5”
Height maximum 12.7mm
Average access time <13ms>
Interface PCI local bus master IDE with ultra
DMA33/ 66/100
FDD
Easy change module 3.5" 1.44MB
CD-ROM(MKECR175)24X
Easy change module
CD type 12.8cm
Height 12.7mm
Datatransfer rate 3600KB/s (max)
Random access time <100m>
Compliance Multimedia PC-2 Spec.

1 - 4
Service Manual
Transport drawertype load/eject
Interface PCI local bus master IDE
BIOS
InSyde 256KB
Display
LCD/CRT (simultaneous) YES
VGA/EGA/CGA/Herculescompatible YES
AGP 3D graphics accelerator YES
Adjustable brightness YES (standard)
LCD\TFT
Backlight CCFT
Size 13.3” or 14.1”
Resolution 1024x768
Color (CRT) 16,77M
Monitor 1280x1024
Support IDCT
Audio
Built-in 2 speakers and 1 microphone YES
3D, Sound Blaster compatible YES
Speaker-outJack YES
Microphone-inJack YES
PowerSupply
AC adapter
AC-in 100-240V/47-63Hz
Capacity 65W
Battery pack NiMH/Li-Ion
PowerSaving Management
Doze mode YES
PS/2 Sleep mode YES
Suspend/Resumemode YES
Suspendto HDD mode YES
Hot key control suspend YES
Closing LCD display off YES
APM ver 1.2 support YES
ACPI Ver 1.0b support YES
Ports
Serialport x 1
IrDA/SIR/ASK/FIR x 1
Parallel port x 1
15 pin external video port x 1

Introduction
1 - 5
External 101/102 keyboard port/ PS/2 mouse x 1
PC Card Standard Type I or Type II x 1
Modem (RJ-11) port for MDC x 1 (optional)
USB connector x 2
speaker-outjack x 1
microphone-injack x 1
LAN (RJ45) port x 1
Physical
Dimension 308 mm(W)
254mm(D)
37.5mm(H)
Weight 3.2KG(with Lithium-lon battery)

Notes

Chipset and Mainboard information
2 - 1
Chapter 2: Chipset and Mainboard information
CPU
The 2200C/2700C Notebook PC uses the Intel Mobile Pentium III/Celeron (.18) processor in an FC-
PGA370 package.
The Intel Mobile Pentium III/Celeron (.18) processor features an integrated L2 cache (256KB for
Pentium III and 128KB for Celeron (.18)) and a 64-bit high performance system bus.
The Mobile Pentium III/Celeron (.18) processor’s 64-bit wide Low Power Gunning Transceiver Logic
system bus is compatible with the SIS630S AGP Set and provides a glue-less, point-to-point interface
for an I/O bridge/memory controller.
The Intel Pentium III and Celerons (.18) processors are fully compatible with all software written for
the Pentium processor with MMX technology, Pentium processor, Intel486 microprocessor, and
Intel386 microprocessor. In addition, they provide improved multimedia & communication perfor-
mance.Their features:
– Performance improved over existing mobile processors
- Supports the Intel Architecture with Dynamic Execution
- Supports the Intel Architecture MMX technology
– Integrated primary (L1) instructions and data caches
- 4-way set associative, 32-byte line size, 1 line per sector
- 16-Kbyte instruction cache and 16-Kbyte writeback data cache
- Cacheable range programmable by processor programmable registers
– Integrated second level (L2) cache
- 4-way set associative, 32-byte line size, 1 line per sector
- Operatedat fullcorespeed

2 - 2
Service Manual
- 128/256-Kbyte, ECC protected cache data array
– Low Power GTL+ system bus interface
- 64-bit data bus, 100-MHz operation
- Uniprocessor,two loads only(processorand I/O bridge/memorycontroller)
- Short trace length and low capacitance allows for single ended termination
– Voltage reduction technology
– Pentium III processor clock control
- Quick Start for low power, low exit latency clock ‘throttling’
- DeepSleep modefor extremely lowpower dissipation
– Thermal diode for measuring processor temperature

Chipset and Mainboard information
2 - 3
Chipsets
SiS630S
The single chipset, SiS630S, provides a high performance/low cost Desktop solution for the Intel Slot
1 and socket 370 series CPU based systems by integrating a high performance North Bridge, ad-
vanced hardware 2D/3D GUI engine, Super-South bridge or an external AGP4X Slot. In addition,
SiS630S provides a system-on-chip solution that complies with the Easy PC Initiative which sup-
ports Instantly Available/OnNow PC technology, USB, Legacy Removal and Slotless Design and
FlexATX form factor.
By integrating the UltraAGPTM technology and advanced 64-bit graphic display interface, SiS630S
delivers AGP 4x performance and memory bandwidth of up to 1 GB/s. In addition, SiS also supports
an extra AGP Slot that supports 4X and Fast Write transactions. Furthermore, SiS630S provides
powerful hardware decoding DVD accelerator to improve the DVD playback performance. In addition
to providing the standard interface for CRT monitors, SiS630S also provides the Digital Flat Panel
Port (DFP) for a standard interface between a personal computer and a digital flat panel monitor.
SiS630S adopts Share System Memory Architecture which can flexibly utilize the frame buffer size
up to 64MB.
The “Super-South Bridge” in SiS630S integrates all peripheral controllers/accelerators /interfaces.
SiS630S provides a total communication solution including 10/100Mb Fast Ethernet for Office re-
quirement and 1Mb HomePNA for Home Networking. SiS630S offers AC’97 compliant interface that
comprises digital audio engine with 3D-hardware accelerator, on-chip sample rate converter, and
professional wavetable along with separate modem DMA controller. SiS630S also provides interface
to Low Pin Count (LPC) operating at 33 MHz clock which is the same as PCI clock on the host, and
dual USB host controllers with six USB ports that deliver better connectivity and 2 x 12Mb band-

2 - 4
Service Manual
width.
The built-in fast PCI IDE controller supports the ATA PIO/DMA, and the Ultra DMA33/66/100
function that supports the data transfer rate up to 100 MB/s. It provides the separate data path for
two IDE channels that can eminently improve the performance under the multi-tasking environ-
ment.
The following illustrates the system block diagram
Features
HostInterface Controller
– Supports Intel Slot 1/Socket370 Pentium II/!!! CPUs
– Synchronous Host/DRAM Clock Scheme
– Asynchronous Host/DRAM Clock Scheme
IntegratedDRAMController
– 3-DIMM/6-Bank of 3.3V SDRAM
– Supports Memory Bus up to 133 MHz
– System Memory Size up to 3 GB
– Up to 512MB per Row
– Supports 16Mb, 64Mb, 128Mb, 256Mb, 512Mb SDRAM Technology
– Suspend-to-RAM (STR)
– Relocatable System Management Memory Region
– Programmable Buffer Strength for CS#, DQM[7:0], WE#, RAS#, CAS#, CKE, MA[14:0] and
MD[63:0]
– Shadow RAM Size from 640KB to 1MB in 16KB increments
– Two Programmable PCI Hole Areas

Chipset and Mainboard information
2 - 5
IntegratedA.G.P.Compliant Target/66Mhz Host-to-PCI Bridge
– AGP v2.0 Compliant
– Supports Graphic Window Size from 4MBytes to 256MBytes
– Supports Pipelined Process in CPU-to-Integrated 3D A.G.P. VGA Access
– Supports 8 Way, 16 Entries Page Table Cache for GART to Enhance Integrated A.G.P. VGA
Controller Read/Write Performance
– Supports PCI-to-PCI Bridge Function for Memory Write from 33Mhz PCI Bus to Integrated
A.G.P.VGA
– Supports Additional AGP slot with 4X and Fast Write Transaction
MeetPC99Requirements
PCI2.2SpecificationCompliant
HighPerformancePCIArbiter
– Supports up to 4 PCI Masters
– Rotating Priority Arbitration Scheme
– Advanced Arbitration Scheme Minimizing Arbitration Overhead.
– Guaranteed Minimum Access Time for CPU And PCI Masters
IntegratedHost-To-PCIBridge
– Zero Wait State Burst Cycles
– CPU-to-PCI Pipeline Access
– 256B to 4KB PCI Burst Length for PCI Masters
– PCI Master Initiated Graphical Texture Write Cycles Re-mapping
– Reassembles PCI Burst Data Size into Optimized Block Size
FastPCI IDE Master/SlaveController
– Supports PCI Bus Mastering

2 - 6
Service Manual
– Native Mode and Compatibility Mode
– PIO Mode 0, 1, 2 , 3, 4
– Multiword DMA Mode 0, 1, 2
– Ultra DMA 33/66/100
– Two Independent IDE Channels Each with 16 DW FIFO
VirtualPCI-to-PCI Bridge
IntegratedUltraAGPVGAforHardware 2D/3D Video/GraphicsAccelerators
– Supports Tightly Coupled 64 Bits Host Interface to VGA to Speed Up GUI Performance and
Video Playback Frame Rate
– AGP v. 2.0 Compliant
– Zero-Wait-State 128x4 Post-Write Buffer with Write Combine Capability
– Zero-Wait-State 128x4 2-Way Read Ahead Cache Capability
– Re-locatable Memory-Mapped and I/O Address Decoding
– Flexible Design Shared Frame Buffer Architecture for Display Memory
– Shared System Memory Area up to 64MB
– Built-in 8K Bytes Texture Cache
– Supports High Quality Dithering
– Supports Bump Mapping
– Supports 8/16/24/32 BPP RGB/ARGB Texture Format
– Supports Video YUV Texture in All Supported Texture Formats
– 128-Bit 2D Engine with a Full Instruction Set
– Maximum 64 MB Frame Buffer with Linear Addressing
– SupportsHardware DVD Accelerator
– Supports Single Frame Buffer Architecture
– Supports Two Independent Video Windows with Overlay Function and Scaling Factors

Chipset and Mainboard information
2 - 7
– Supports YUV-To-RGB Color Space Conversion
– Supports Graphic and Video Overlay Function
– Supports CD/DVD to TV Playback Mode
– Simultaneous Graphic and TV Video Playback Overlay
– Supports RGB555, RGB565, YUV422 and YUV420 Video Playback Format
– Supports Filtered Horizontal Up and Down Scaling Playback
– Supports DVD Sub-Picture Playback Overlay
– Supports DVD Playback Auto-Flipping
– Built-in Two Video Playback Line Buffers
– Built-in Programmable 24-bit True-Color RAMDAC up to 270 MHz Pixel Clock RAMDAC
Snoop Function
– Built-in Dual-Clock Generator
– SupportsMultiple Adapters andMultiple Monitors
– Built-in PCI Multimedia Interface
– Supports Digital Flat Panel Port for Digital Monitor (LCD Panel)
– Built-in VESA Plug and Display for CH7003, PanelLinkTM and LVDS Digital Interface
– Built-in Secondary CRT Controller for Independent Secondary CRT, LCD or TV digital
output
– Supports VESA Standard Super High Resolution Graphic Modes
- 640x480 16/256/32K/64K/16M colors 120 Hz NI
- 800x600 16/256/32K/64K/16M colors 120 Hz NI
- 1024x768 256/32K/64K/16M colors 120 Hz NI
- 1280x1024 256/32K/64K/16M colors 85 Hz NI
- 1600x1200 256/32K/64K/16M colors 85 Hz NI
- 1920x1440 8bbp/16bbp 60NI

2 - 8
Service Manual
– Low Resolution Modes
– Supports Virtual Screen up to 4096x4096
– Fully Directx 7.0 Compliant
– Efficient and Flexible Power Management with ACPI Compliance
LowPin Count Interface
– Forwards PCI I/O and Memory Cycles into LPC Bus
– Translates 8-/16-bitDMA Cycles into PCI Bus Cycles
AdvancedPCIH/WAudio&Modem
Advanced Power Management
– Meets ACPI 1.0 Requirements
– Meets APM 1.2 Requirements
– ACPI Sleep States Include S1, S3, S4, S5
– CPU Power States Include C0, C1, C2 C3
– Power Button with Override
– RTC Day-of-Month, Month-of-Year Alarm
– 24-bit Power Management Timer
– LED Blinking in S0,S1 and S3 States
– SystemPower-Up Events Include:Power Button, Hot-Key,Keyboard Password/ Hot-Key,
RTC Alarm, Modem Ring-In, SMBALT#, LAN, PME#, AC’97 Wake-Up and USB
– Wake-Up
– SoftwareWatchdog Timer
– Power Supply’98 Support
– PCI Bus Power Management Interface Spec. 1.0
IntegratedDMA Controller

Chipset and Mainboard information
2 - 9
– Two 8237A Compatible DMA Controllers
– 8/16- bit DMA Data Transfer
– Distributed DMA Support
IntegratedInterrupt Controller
– Two 8237A Compatible DMA Controllers
– Two 8259A Compatible Interrupt Controllers
– Level- or Edge-Triggered Programmable
– Serial IRQ
– Interrupt Sources Re-routable to Any IRQ Channel
Three 8254CompatibleProgrammable 16-bit Counters
– System Timer Interrupt
– Generate Refresh Request
– Speaker Tone Output
IntegratedKeyboard Controller
– Hardwired Logic Provides Instant Response
– Supports PS/2 Mouse Interface
– Password Security andPassword Power-Up
– System Sleep andPower-Up by Hot-Key
– KBC and PS2 Mouse Can Be Individually Disabled
IntegratedReal Time Clock(RTC) with 256B CMOS SRAM
– Supports ACPI Day-of-Month and Month-of-Year Alarm
– 256 Bytes of CMOS SRAM
– Provides RTC H/W Year 2000 Solution
Universal Serial Bus Host Controller