Climax CL-DR-AMS2X4-N User manual

Rail Mounting
Audio Matrix Switch is designed to be installed on a standard
35 mm wide DIN rail (EN 50022, BS 5584).
Hook the module from the top, pull down the rail mounng
clips, push the module to the rail and release the rail
mounng clips.
Screw Mounting
Screw the module to any surface through 4 corner screw
holes.
3
4
1
2
INSTALLATION GUIDE version 1.0.1
Compatible with Control4
Audio Matrix Switch (CL-DR-AMS2X4-N)
Input Voltage
18V-24V DC (24V DC is recommended)
Input Current
170mA (for 24V DC)
I/O Connections
C-Bus
2 X Rj45
Output
4 audio channel-10A per channel X
rising-cage 5mm screw terminals)(
Input
2 audio channel-10A per channel X
rising-cage 5mm screw terminals)(
Product Specificaon
12
3
Change Module Address
In order to change the module address follow steps below consecuvely and uninterruptedly:
1. Disconnect the main power. Hold buon #1 & #2 simultaneously (buon’s and LED’s number
sequence is considered from right to le as shown in following picture).
2. Reconnect the main power. Release buon #2 aer LEDs #1 to #4 flashed. Then release buon
#1 aer LEDs #1 and #2 flashed. Power LED will start flashing quickly.
3. Press buon #1, 4 mes. Then the module address will be displayed by LEDs in binary.
4. Press buon #1 to increase the module address and buon #2 to decrease it.
5. Press buon #3 to save the module address and buon #4 to cancel. Aer saving the new module
address or canceling the process, the module will reset.
The devices which are connected from a common interface cannot have same module
address.
1
1
1
8
8
4
4
7
6
5
2
1
1. Screw holes
2. Output connectors
3. Input connectors
4. Rail mounng clips
5. Indicator LEDs
6. Status LEDs
7. Control buons (1-4)
8. RS-485 jack
2
3
Compatible with Control4
#1
#2
#3#4
#1#2
#3#4
#5
#6#7#8

Compatible with Control4
AMP
L
R
GND
Zone 4
AMP
L
R
GND
Zone 3
L
R
GND Zone 1
L
R
GND Zone 2
Input 1
Input 2
Audio OutAudio Out
Compatible with Control4
L
R
GND
Zone 4
L
R
GND
Zone 3
L
R
GND Zone 1
L
R
GND Zone 2
AMP
Input 1
Input 2
AMP AMP
Audio Out
Audio Out
AMP
57
68
Follow this wiring for direct or network use of module.
From: Previous Module
Based on following wiring diagram, it would be possible to control volume of each zone by
controlling its relevant amplifier.
It is recommended to use short length shielded cable for input connecons.
The amplifier you select for your project must be powerful enough to support 4 audio zone.
Use the following wiring diagram, if you don’t need to control volume of each zone separately.
Use the terminator socket for the last module in C-Bus network.
Before wiring the device, always unplug the main power.
Module’s LEDs
Power: When the module is connected to main power, “Power LED” will flash smoothly.
Status: When the module is connected to C-Bus network and receives valid data packets, “Status
LED” flashes quickly. “Status LED” is “off” when the module doesn’t receive any data. In direct
mode, “Status LED” will flash once when the module receives a valid data packet from Home
Controller.
When the module is receiving invalid data packet ,”Status LED” will remain “on” for 5 seconds.
In some cases, when a new module is added to C-Bus network, “Status LED” might remain “on”
for 5 seconds. This situaon must not be considered as an error.
Out1 to Out4: Shows connecon status of module’s audio inputs/outputs. Also when the module is
connected to main power, The channel LEDs will display the module address in binary for 2
seconds.
To: Next Module