CMP 25207-7 Series User manual
®
EQUALIZER POOL SUCTION
25207-7XX-000, 25207-8XX-000
IAPMO Listed VGBA Suction: Compliant to ANSI/APSP - 16 2017 & CPSC
Requirements
All Custom Molded Products main drains are listed and tested in strict accordance
to the requirements of ANSI/APSP-16 2017, the current standard of reference for
the Virginia Graeme Baker Act, and compliant to the latest Consumer Product
Safety Commission (CPSC) requirements.
Connect only to a skimmer. Do not use as a pump suction. May be used as a single
VGBA TESTED & CERTIFIED
ANSI-APSP 16 | CPSC
2
TABLE OF CONTENTS
Please read through the entire manual before installing your new unit. Your pool drain tting must be installed and operated as
specied.
A. Safety Instructions & Precautions ......................................................................................... 3
.......................................................................................... 4
C. Installation & Maintenance Procedures .............................................................................. 5
1. Required for Installation...................................................................................... 5
2. Installation Location ............................................................................................ 5
3. Installation Procedure ......................................................................................... 5
................................................................................ 7
............................................................................................................. 7
D. Diagram & Measurements ...................................................................................................... 8
E. Parts List......................................................................................................................................... 9
IMAGES & TABLES IN THESE INSTRUCTIONS
page 4 FLOW RATES
page 4 SPECIFICATIONS
page 4 HEAD LOSS CHART
page 6 INSTALLATION
page 8 DIMENSIONS
3
A. SAFETY INSTRUCTIONS & PRECAUTIONS
Attention Installer: This manual contains important information about the installation, operation and safe use of this
recommendations.
death.
manufacturers.
WARNING
WARNING
WARNING
WARNING
WARNING
NOTICE
NOTICE
NOTICE
NOTICE
NOTICE
NOTICE
NOTICE
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS.
READ, UNDERSTAND AND FOLLOW ALL WARNINGS AND INSTRUCTIONS.
ALWAYS PLUMB AND INSTALL ALL SUCTION FITTINGS ACCORDING TO ALL
BUILDING CODES THAT APPLY IN YOUR AREA.
B. SIZING & SPECIFICATION REFERENCE
•
•
•
of suction beyond rated safety limits causing entrapment or death.
•
•
•
TABLE 1: SPECIFICATIONS
PIPE SIZE 2” Insider (25207-7xx - Gunite Only)
1.5” MIP (25207-8xx - Fiberglass, Vinyl or Gunite)
OPEN AREA 6.82in2
SUCTION COVER LIFE
TOTAL HEAD LOSS (Feet of Head)
FLOW RATE (GPM)
1
0 10 20 30 40 50 60 70
2
0
3
4
5
6
7
1.5IN PIPE 2IN PIPE
2.7
3.05
4.36
3.32 3.78
3.43
3.89
6.54
4.36
5.46
CHART 1: HEAD LOSS CHARTS
5
1. REQUIRED FOR INSTALLATION
Your drain/suction includes the following:
•
•
•
•
2. INSTALLATION LOCATION
a.
b. Do not mount directly under seats.
c.
SAFETY CHECKLIST:
d.
e.
f.
replaced before use.
3. INSTALLATION PROCEDURE
2 INCH INSIDER INSTALLATION
a.
b.
c.
(IMAGE 2)
d.
e.
1.5 INCH MIP INSTALLATION
a.
b.
c.
d.
e.
C. INSTALLATION & MAINTENANCE
6
C. INSTALLATION & MAINTENANCE
•
•
•
•
grate and fasteners.
installation.
Pool Wall
Skimmer
Equalizer
To Pump Suction
IMAGE 1 -POOL/PLUMBING INSTALLATION
7
Equalizer fitting
is concave to fit
over pool wall fitting
Insider Fitting 1.5in Threaded
MIP Fitting
IMAGE 2 -PIPE FITTING OPTIONS
2. MAINTENANCE & INSPECTION
a.
b.
c.
d.
must be replaced. Do not use the pool/spa/facility until a replacement is made.
e.
not use the pool/spa/facility until a repair or replacement is made.
f.
• Close the pool or spa immediately
• Post a closure notice
•
•
area.
•
•
•
from freeze damage.
C. INSTALLATION & MAINTENANCE
8
D. PART DIAGRAMS AND MEASUREMENTS
IMAGE 3 -DIMENSIONS
4"
2-5/8"
2"
1.5"
1-1/8"
4"
2"
1.5"
0.5"
G. PARTS LIST
Parts numbers not listed in product table are only available as part of a complete assembly.
*See c-m-p.com or pool products catalog for other color and kit options
1
2
3
4
5
CMP P/N DESCRIPTION
1 61000-050-012 -32 1-
2 61000-100-316 ()
3 25207-020-000* COVER
25207-700-010 -2” INSIDER
5 25207-800-010 -1.5” MIP
10
11
Record Information on this System Below & Keep for Your Records
Installer _______________________________________________________________
Purchased From _______________________________________________________
Installation Date _____________________________
Model Number ______________________________
Pool Size in Gallons __________________________
CMP Customer Service & Tech Support
FAX: 770-732-7115
suppor[email protected]
Warranty Questions
Support Resource & Videos Online
c-m-p.com/resourcecenter
0521sb
This manual suits for next models
1
Table of contents
