Cobalt Digital Inc BLUE-MOB User manual

BLUE-MOB MOBILE ADAPTER GUIDE For Compatible Wireless Audio Accessories Bluetooth Adapter Model No.: BLUE-MOB Made in Taiwan The BLUE-MOB Mobile Adapter allows you to use a compatible wireless headset or other audio accessory with your mobile or base station two-way radio. BLUE-MOB™ and COBALT AV™ are trademarks owned by ComtronICS, Lexington KY. All other product or service names are the property of their respective owners. © 2014 ComtronICS | Cobalt AV. All Rights Reserved.
Controls and Connections
NOTE: BT-M83 Model shown.
Other models may vary slightly in appearance.
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o_ and on, the user is encouraged to try to correct the interference by one of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. - Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.To maintain compliance with FCC RF exposure compliance requirements, please avoid direct contact to the transmitting antenna during transmitting.
version 1.0 June 2014
2350 FORTUNE DRIVE • LEXINGTON KY 40509
PH: 859.299.9494 FAX: [phone]
TOLL FREE: 800.264.6021
WWW.COBALTAV.COM
Status LED
The LED ashes messages that lets
the user know the current status of
the COBALT BLUE-MOB Mobile Adapter.
Connection Cable
The COBALT BLUE-MOB Adapter uses shielded cable to
connect the adapter to the mobile/base station radio
Adapter Housing
The Bluetooth and radio interface circuitry of the
COBALT BLUE-MOB Mobile Adapter are contained
inside this compact and rugged polycarbonate housing
Velcro for Mounting
The Velcro pad on the bottom
of the COBALT BLUE-MOB Mobile
Adapter allows it to be mounted in a
convenient location near the mobile/base
station two-way radio
External PTT Jack
This 2.5 mm Tip-Sleeve (TS) style jack
can be used to connect an (optional)
external Push-to-Talk device (such as
a foot switch) to the adapter. The correct
method for wiring the external switch
appears below.
Radio Connector
The radio connector
is the part of the
adapter that plugs
into your mobile
or base station
two-way radio
STEP ONE: Connecting the Mobile Adapter to a Two-Way Radio
* When connecting the COBALT BLUE-MOB Bluetooth Adapter to a two-way mobile radio, rst
make sure that the two-way radio is powered o.
* Insert the radio connector of the Mobile Adapter into the corresponding jack on the two-way
radio. Push the connector into the jack until it is rmly seated.
NOTE: Most models of COBALT BLUE-MOB Mobile Adapter connect to the accessory plug on the
rear of the two-way radio. However, some models may connect to the radio’s front microphone
jack and/or rear external speaker jack.
* On some models you may need to tighten one or more retaining screws on the adapter after
plugging the Mobile Adapter’s connector into the two-way radio.
* If you will use the COBALT BLUE-MOB Mobile Adapter with a wired Push-to-Talk (such as a
footswitch) plug the connector for the PTT into the External PTT Jack of the adapter and mount
the switch.
Reprogramming the Radio
* In order for the COBALT BLUE-MOB Mobile Adapter to work properly, some two-way mobile radios
may require reprogramming using the radio’s manufacturer’s Computer Programming Software and
a programming cable. This may be necessary to ensure that all of the needed signals are available on
the radio’s accessory port or to set audio levels to match the headset.
* If you believe that your radio requires reprogramming (or are unsure) you should contact your
two-way radio dealer or COBALT AV’s technical support.
Mounting the Adapter
Velcro is supplied with the COBALT BLUE-MOB Mobile Adapter allowing you to secure the adapter to
nearly any location near the mobile two-way radio. For convenience, you should mount the adapter
somewhere that the user will be able to see the status LED and to reach the Multifunction Button for
ease of use. Mounting adapter as high as possible and making sure it is not blocked by metal or
electrical devices will ensure best possible wireless range.
STEP TWO: Pairing the COBALT BLUE-MOB Mobile Adapter with a Bluetooth Headset
* Make sure that the mobile two-way radio and Bluetooth Headset are both turned OFF. The
Bluetooth Headset should be fully charged.
* Put the Bluetooth Headset into pairing mode following the instructions provided by the headset’s
manufacturer.
* On the COBALT BLUE-MOB Mobile Adapter, press and hold the Multifunction Button while turning
the radio ON. Continue to hold the Multifunction button down for approximately three seconds.
Release the button when the status LED of the adapter begins to ash two times per second. The
COBALT BLUE-MOB Mobile Adapter is now in headset pairing mode.
NOTE: Your two-way mobile radio may transmit during this process. You should set the radio to a
channel where interference to other operations will be minimized while you are pairing these devices.
* Place the Bluetooth Headset near the COBALT BLUE-MOB Mobile Adapter and wait. Within a few
seconds, the devices should synch to each other. Once paired, the LED on Mobile Adapter will
change to a long blue ash followed by a single blue ash every few seconds.
* If the COBALT BLUE-MOB Mobile Adapter does not detect a compatible Bluetooth Headset within
sixty seconds of being put into pairing mode, the adapter will exit the pairing mode and resume
normal operation.
2
3 4
FIG. 1 Connecting a remote PTT
FIG. 2 Typical Rear Connection Type Radio
FIG. 3 Typical Front and Rear Connection Radio
BT-PTT Wireless
PTT Switch (optional)
Your headset device
FIG. 4 - Wireless Communication System
Multifunction Button
This button is used to place
the COBALT BLUE-MOB
Mobile Adapter in pairing mode.
It can also be used as a Push-to-Talk
(PTT) button

STEP THREE: Pairing the PRYMEBLU Mobile Adapter and PRYMEBLU PTT (OPTIONAL)
* Make sure the mobile two-way radio, Bluetooth Headset, and COBALT BT-PTT are all turned
OFF. The BT-PTT should be fully charged.
* On the BLUE-MOB Mobile Adapter, press and hold the Multifunction Button while turning
the radio ON. Continue to hold the Multifunction button down for approximately three
seconds. Release the button when the status LED of the adapter begins to ash two times
per second.
NOTE: Your two-way mobile radio may transmit during this process. You should set the radio
to a channel where interference to other operations will be minimized while you are pairing
these devices.
* Once again, press the Multifunction Button on the BLUE-MOB Mobile Adapter. Release the
button. The LED indicator on the Mobile Adapter should now ash three times per second.
The BLUE-MOB Mobile Adapter is now in PTT pairing mode.
* On the COBALT BT-PTT, press and hold the Push-to-Talk button while setting the power
switch to the ON position. Continue to hold the Push-to-Talk button down until you see the
LED indicator change to a series of rapid ashes. Release the Push-to-Talk button. The BT-PTT
is now in pairing mode.
* Place the BT-PTT near the BLUE-MOB Mobile Adapter and wait. Within a few seconds, the
devices should synch to each other.
* Once paired, the LED on Mobile Adapter will change to a long blue ash followed by a
single blue ash every few seconds. The LED on the BT-PTT will also show a quick single ash
every second.
* If the BLUE-MOB Mobile Adapter does not detect a compatible BT-PTT within sixty seconds
of being put into pairing mode, the adapter will exit the pairing mode and resume normal
operation.
Reconnecting to a Previously Paired Headset / COBALT PTT
Once the BLUE-MOB Mobile Adapter has been successfully paired to a Bluetooth Headset or
COBALT BT-PTT, it will remember those connections. If the headset or BT-PTT is powered oor
loses connection, the adapter will attempt to reestablish the connection. The adapter and
headset/BT-PTT will attempt to reestablish their link whenever when the devices are powered
on and in within range of each other. Re-establishing this connection can take 10-60 seconds.
STATUS LED MESSAGES
The meanings of the various status LED
messages shown by the BLUE-MOB Mobile
Adapter are shown on the following table:
LED INDICATION
One ash every 4 seconds
Two ashes per second
Three ashes per second
One long ash for three seconds
No indication
MEANING
Normal operation
Headset pairing mode active
PTT pairing mode active
Successfully paired or re-paired
Radio is turned oor no power is being supplied to the adapter
TROUBLESHOOTING
My Bluetooth Headset or COBALT Push-to-Talk will not pair with the BLUE-MOB Adapter. Try
re-pairing the BLUE-MOB Mobile Adapter and Bluetooth accessory following the instructions in this
guide. Make sure that the BLUE-MOB Mobile Adapter and accessory being paired are within one meter
of each other. If possible, isolate them from other Bluetooth devices such as phones, laptops, etc. that
might interfere with the pairing process.
My Bluetooth Headset or COBALT Push-to-Talk worked with the BLUE-MOB Adapter
previously, but is not working now. Make sure that the BLUE-MOB Mobile Adapter is properly
connected to the two-way radio and that the adapter has power supplied to it. Ensure that your wireless
audio accessory has a fully charged battery and is turned on. If the devices will still not work, re-pair the
BLUE-MOB Mobile Adapter to the wireless accessories.
I can transmit using the Multifunction Button on the BLUE-MOB Mobile Adapter and transmit
audio is picked up from my Bluetooth Headset; however the PTT button on my COBALT
Push-to-Talk does not key the radio. Your COBALT BT-PTT is not properly paired with the BLUE-MOB
Mobile Adapter or has come un-paired. Try pairing the adapter and BT-PTT again.
I can transmit using the Multifunction Button on the BLUE-MOB Mobile Adapter or the PTT
button on the COBALT Push-to-Talk but no microphone audio is being heard. Your Bluetooth
Headset is not properly paired with the PRYMEBLU Mobile Adapter or has come un-paired. Try pairing
the adapter and headset again.
I have my BLUE-MOB Mobile Adapter plugged into my Mobile Two-Way radio but when I turn
the radio on, the LED on the adapter does not light up. Many radios have an internal micro fuse
which protects the radio from being damaged if an accessory draws too much power from the accessory
connector. This fuse might blow if the BLUE-MOB Mobile Adapter is plugged into or unplugged from
the two-way radio while the radio is powered on. You may need to contact your radio dealer to
have this fuse replaced.
I need more range from my BLuetooth headset. Try to mount the BT-Mxx as high as possible and
clear of any obstructions.
STEP FOUR: Transmit and Receive Operation
Push-to-Talk can be activated by any of the following methods:
* Pressing and holding the Multifunction button of the BLUE-MOB Mobile Adapter
* Pressing and holding the PTT button on the COBALT PTT (if a BT-PTT is paired to the Mobile
Adapter).
* Pressing and holding the button on the external Push-to-Talk/Footswitch (if one is plugged
into the Mobile Adapter) or pressing and holding the PTT switch on any specially designed
COBALT headset (such as the BT-LMIC, BT-Earmuor BT-Throat Mic.) Please note the function
key on a normal cell phone type headset DOES NOT activate the radio PTT.
When transmitting, the operator’s voice is picked-up by:
* The microphone in the Bluetooth Headset.
NOTE: If you are using a model of BLUE-MOB Mobile Adapter that connects to the rear
accessory jack on the mobile radio, then you can leave the radio’s hand microphone attached
and use it as a back-up if you wish. Pressing and holding the PTT button on the hand
microphone will cause the radio to transmit and the operator’s voice will be picked up by the
hand microphone.
Receive audio is handled dierently depending on whether the model of BLUE-MOB Mobile
Adapter you are using connects to the radio’s rear accessory jack or front microphone
jack/rear speaker jack.
If the adapter you are using connects to the radio’s rear accessory jack:
* Receive audio can be heard over both the radio’s internal speaker or over the earphone in
the Bluetooth Headset.
* The volume control knob on the radio controls the internal speaker volume only. If you do not
wish to hear received signals over the internal speaker, simply set the radio’s volume to zero.
* The volume of the earphone can be controlled using the Volume Up/Down buttons on the
Bluetooth Headset.
If the adapter you are using connects to the radio’s front microphone jack and rear speaker jack:
* Receive audio can be heard only on the earphone in the Bluetooth Headset. The internal
speaker in the radio will be disabled.
* Receive audio volume should be set primarily using the volume control knob on the radio. You
can ne tune the volume if needed using the Volume Up/Down keys on the Bluetooth Headset.
SUPPORT AND WARRANTY
COBALT AV warrants this product against defects in materials or workmanship for a period of
one year from the date of retail purchase. COBALT AV will repair or replace a defective unit, at
our option, without charge for parts or labor. The limited warranty is extended only to the
original purchaser and is valid only to consumers in the United States and Canada. It does not
cover damage or failure caused by or attributable to Acts of God, abuse, misuse, improper or
abnormal usage, faulty installation, improper maintenance, lightning, or other incidences of
excessive voltage, or any tampering or repairs by other than a COBALT AV authorized repair
facility. It does not cover replacement of consumable parts, transportation costs, or damage in
transit.
Repair or replacement under the terms of this warranty does not extend the terms of this
warranty. This warranty can only be modied by an ocer of COBALT AV, and then only in
writing. Should this product prove defective in workmanship or material, the consumer’s sole
remedies shall be such repair or replacement as provided by the terms of this warranty. Under
no circumstances shall COBALT AV be liable for any loss or damage, direct, consequential, or
incidental, arising out of the use of or inability to use this product. Some states do not allow
limitations on how long an implied warranty lasts or the exclusions or limitations of incidental
or consequential damages, so the above limitations or exclusions may not apply to you. This
warranty gives you specic legal rights. You may also have other rights, which may vary, from
state to state.
To return your product for service or repair, please contact our oce to be issued an RMA
number. PLEASE DO NOT RETURN ANY PRODUCT WITHOUT AN RMA NUMBER.
COPYRIGHT AND TRADEMARK INFO
© 2014 ComtronICS | Cobalt AV, Lexington KY. All rights reserved.
BLUE-MOB™ and COBALT AV™ are trademarks owned by ComtronICS. All other product or
service names are the property of their respective owners.
DISCLAIMER: The Bluetooth link used in this product is an open standard, unsecured
technology. As such, it is not recommended for rst-responder or other mission critical users.
65
7 8