Cobra microTALK MT 725 User manual

ENGLISH
POWER Button
VOLUME CONTROL
Buttons
MODE Button
CHANNEL SELECT
Buttons
Speaker/Microphone
CALL Button
External Speaker/
Microphone Jack
TALK Button
LIGHT/MAX
RANGE Button
Charge/Intercom
Jack
Antenna
Two-Way Radio Model MT 725
LOCK Button
Main Channel Number
CTCSS Privacy
Code Numbers Receive/Transmit
Lock
Power Saver
Battery Level Indicator Dual Watch
Baby Monitor
VibrAlert®/Call Alert
VOX
Scan
Roger Beep
Keystroke Tone
Belt Clip
Battery Compartment
Lock Tab
Wrist Strap Connection Location
This equiment is intended for use in:
• Countries of use
PT •
SE •
CH •
SI •
SK •
TR •
LI •
LU •
MT •
NL •
NO •
PL •
HU •
IE •
IS •
IT •
LT •
LV •
EE •
ES •
FI •
FR •
GB •
GR •
AT •
BE •
CY •
CZ •
DE •
DK •

PRODUCT FEATURES
• Two-Way Radio with up to a 3 km
(2 mile) range
• 8 Channels*
• 38 CTCSS Privacy Codes
• Backlit LCD Display
• Water Resistant
• Battery Saver Circuitry
• Maximum Range Extender
• VOX Mode for Hands-Free
Transmissions
• VibrAlert®Silent Paging
• Baby Monitor Function
• Intercom Capability
• Call Alert (5 Selectable Tones)
• Scan (Channel, Privacy Code)
• Dual Watch Programmable
2-Location Scan
• Key Lock
• Auto Squelch
• Selectable On/Off "Roger Beep"
Confirmation Tone
• Selectable On/Off Keystroke Tone
• External Speaker/Microphone Jack
• Belt Clip
• Wrist Strap
• Battery Charge Contacts in Battery
Compartment Door
• Two-Port Rapid Desktop Charger
with AC Adapter (240V, 3-Pin
UK Plug)
• Two Rechargeable NiMH
Battery Packs
*You are not allowed to use channels 1 and 2 in
France.
This situation can change; please contact the French
radio licensing authority for more information.
English
Product Information
This microTALK®radio has been manufactured to meet all required standards
for radio equipment using PMR 446 frequencies as authorized. The use of
this two-way radio product involves the public airways and its use may be
subject to local laws or regulations. Contact your radio licensing authority for
more information.
Caring for Your Radio
Your microTALK®radio will give you years of trouble-free service if cared for
properly. Here are a few suggestions:
• Handle the radio gently.
• Keep it away from dust.
• Never put the radio in water or in a damp place.
• Avoid exposure to extreme temperatures.
Product Features

OPERATION
Battery Installation
To Install or Replace Batteries:
1. Remove belt clip by releasing belt
clip latch and sliding clip Up.
2. Pull down on the BATTERY DOOR
LOCK TAB to remove the battery
compartment cover.
3. Insert the rechargeable NiMH battery pack (part No. FA-BP) according to
instructions indicated on battery pack.
NOTE: Four high-quality alkaline (4) AAA batteries can
also be used. Position batteries according to
polarity markings.
4. Replace Battery Compartment cover and belt clip.
Battery Pack Charging
Your microTALK®radio includes two (2) rechargeable
NiMH battery packs (part No. FA-BP) and a two-port
rapid desktop charger (part No. PA-CD).
Your two-port rapid desktop charger is capable of
recharging:
English
a. One (1) radio (with battery pack installed in
battery compa-rtment) and one (1) battery pack
using the included battery pack guide in the radio
charging well.
b. Two (2) radios (with battery pack installed in
battery compartment).
c. Two (2) battery packs using the included battery pack guides in the
radio charging wells.
You should fully charge the included rechargeable NiMH battery packs (part
No. FA-BP) before using your microTALK®radios for the first time.
NOTE: Estimated Operation Time On Full Charge: 15 Hours.
This rechargeable battery must be recycled or disposed of properly in
compliance with all applicable laws. It must not be thrown away with
household rubbish.
NOTE: Do not put batteries into fire or expose to high heat. They may
explode.
Remove Belt Clip Lock Tab
Insert Batteries
Battery Packs &
Desktop Charger
One Battery Pack &
One Radio

OPERATION
To Recharge the Rechargeable NiMH Battery Pack In Radio:
1. Attach the POWER SUPPLY to the
charger base and plug it into an
electrical socket.
2. Place the rechargeable NiMH
BATTERY PACK (part No. FA-BP) in
the battery compartment (see “Battery Installation”).
3. Place the RADIO in the charger base.
The CHARGE light on the charger base will indicate when
the radio is inserted into the charger properly.
A full charge will take approximately three (3) hours. You
can leave the unit in the charger indefinitely.
It is recommended that your radio should be turned off while being charged.
WARNING: Only the NiMH battery pack FA-BP can be recharged.
To Recharge the Rechargeable NiMH Battery Pack:
1. Attach the POWER SUPPLY to the
charger base and plug it into an
electrical socket.
2. Insert BATTERY PACK GUIDE in the
radio charging well.
English
3. Place the rechargeable NiMH BATTERY PACK (part No.
FA-BP) in the charger base with metal contacts facing
rear of charger stand.
The CHARGE light on the charger base will indicate when
the rechargeable NiMH battery pack (part No. FA-BP) is inserted into the
charger properly.
A full charge will take approximately three (3) hours. You can leave the the
battery pack in the charger indefinitely.
WARNING: Only the NiMH battery pack FA-BP can be recharged.
Optional Battery Charging
When the NiMH battery pack (part No. FA-BP) is used,
the battery pack can be charged using the optional rapid
wall mount charger (part No. PA-CW). Simply place the
battery pack in the battery compartment, open the
CHARGE/INTERCOM tab on the side of the unit and insert
the plug into the charge jack to start charging. The
batteries should be fully charged in about three (3)
hours.
WARNING: Only the NiMH battery pack FA-BP can be
recharged.
NOTE: See “Optional Accessories” for accessory
availability and ordering instructions.
Charging Batteries
Charge/Intercom
Tab
Battery Pack
In Radio
Charging Battery
Packs In Radios
Insert Battery Pack
Guide(s)
Charging Battery
Packs Only
Attach Power Supply
Attach Power Supply

OPERATION
Radio Power
To Turn Your Radio On:
1. Press and hold the POWER button until you hear a
series of audible tones indicating that the radio is On.
Your microTALK®radio is now in LISTENING MODE, ready
to receive transmissions. The radio is always in
LISTENING MODE, except when the TALK, CALL or MODE
buttons are pressed.
To Turn Your Radio Off:
1. Press and hold the POWER button.
Battery Low Indicator
Battery power is indicated by the segments appearing at
the bottom of the display. As battery power decreases,
fewer segments will be visible. When the last segment
begins to flash, the batteries should be replaced or
recharged.
WARNING: Only the NiMH battery pack FA-BP can be recharged.
Battery/Power Saver
If there are no transmissions within ten (10) seconds,
English
the unit will automatically switch to Battery Save Mode
and POWER SAVER will appear in the display. This will
not affect the unit’s ability to receive incoming
transmissions.
Communicating with Another Person
To Talk To Another Person:
1. Press and hold the TALK button.
2. With the microphone about 5 cm (2 inches) from your
mouth, speak in a normal voice.
3. Release the button when you have finished talking
and listen for a response.
You cannot receive incoming calls while pressing the TALK
button.
NOTE: Both radios must be tuned to the same channel
and privacy code to communicate.
Listening for a Response
When You Have Finished Talking:
1. Release the TALK button to receive incoming
transmissions. Your microTALK®is always in LISTENING
MODE except when the TALK, CALL or MODE buttons
are pressed.
Power Button
Battery Low
5 cm (2 Inches)
From Mouth
Talk Button
Power Saver
Listening

OPERATION
Volume
To Adjust the Volume:
1. Press the VOLUME UP or the
VOLUME DOWN buttons.
A triple beep sound is used to indicate
that you have reached the minimum
(1) or maximum (8) volume level.
Call Button
To Alert Another Person That You Are Calling:
1. Press and release the CALL button.
The other person will hear a two (2) second ringing tone.
You cannot receive transmissions while sending a call.
NOTE: Both radios must be tuned to the same channel
and privacy code to communicate.
Channels
To Select a Channel:
1. With the radio on, select any of the 8 channels by
pushing the CHANNEL UP or CHANNEL DOWN button.
You can press and hold the CHANNEL UP or CHANNEL
English
DOWN button for fast advance.
NOTE: Both radios must be tuned to the same channel
and privacy code (see “CTCSS Privacy Codes”) to
communicate.
Lock Function
The LOCK button locks the CHANNEL UP, CHANNEL DOWN, MODE and POWER
buttons to prevent accidental operation.
To Use the Lock Function:
1. Press and hold the LOCK button for
two (2) seconds to turn the Lock
On or Off.
A double beep sound is used to
confirm your Lock On or Off request.
When the radio is in Lock Mode, the Lock icon will be displayed.
Display Illumination
To Illuminate Your Display:
1. Press and release the LIGHT/MAX RANGE button to
illuminate the display for ten (10) seconds.
Call Button
Volume Level
Volume Buttons
Lock Button
Channel Buttons
Channels
Lock Icon
Light/Max Range
Button

OPERATION
Auto Squelch/Maximum Range Extender
Your microTALK®radio is equipped with Auto Squelch, which automatically
shuts off weak transmissions and unwanted noise resulting from terrain,
conditions, or from reaching your maximum range limit.
You can temporarily turn Off Auto Squelch or turn On Maximum Range
Extender, allowing all signals to be received and extending the maximum
range of your radio.
To Temporarily Turn Off Auto Squelch:
1. Press the LIGHT/MAX RANGE button for less than five
(5) seconds.
If you hear two (2) beeps, you have turned the
Maximum Range Extender On (see below).
To Turn Maximum Range Extender On:
1. Press and hold the LIGHT/MAX RANGE button for at least five (5) seconds
until you hear two (2) beeps, indicating that the Maximum Range
Extender is On.
To Turn Maximum Range Extender Off:
1. Press and release the LIGHT/MAX RANGE button or change channels.
English
microTALK®Range
Your microTALK®radio has a range of up to three (3)
kilometres (2 miles). Your range will vary depending on
terrain and conditions.
In flat, open country your radio will operate at
maximum range.
Buildings and foliage in the path of the signal can
reduce the range.
Dense foliage and hilly terrain will further reduce the
signal.
Remember, you can achieve maximum range by using
Maximum Range Extender. See above for details.
Light/Max Range
Button
Maximum Range
Reduced Range
Reduced Range

OPERATION and
MODE FUNCTIONS
External Speaker/ Microphone Jack
Your microTALK®radio can be fitted with an optional
external speaker/microphone (not included), freeing your
hands for other tasks.
NOTE: See “Optional Accessories” for accessory
availability and ordering instructions.
To Attach the External Speaker/Microphone:
1. Open the SPKR/MIC tab on top of the radio.
2. Insert the plug into the SPKR/MIC jack.
Intercom
With the optional intercom adapter and two external
speaker/microphone attachments, a single microTALK®
radio can be used as an intercom system. (Ideal for
motorcyclists.) Contact your local dealer for availability
and pricing.
English
Scrolling Through the Mode Functions
By scrolling through the Mode Functions, you will be able to select or change
preferred features of your microTALK®radio. While you are scrolling through
the Mode Functions, your radio features will be displayed in the same
predetermined order:
Set CTCSS Privacy Codes
Set VOX On/Off
Set VOX Sensitivity Level
Set Channel Scan
Set CTCSS Privacy Code Scan
Set VibrAlert®and/or Call Alert
Set Baby Monitor
Program Dual Watch Location or
Set Dual Watch On/Off
Set Call Tones
Set “Roger Beep” On/Off
Set Keystroke Tones On/Off
Intercom
External Speaker/
Microphone

MODE FUNCTIONS
CTCSS Privacy Codes
CTCSS (Continuous Tone Coded Squelch System) is an advanced tone coding
system allowing you to select one of 38 privacy codes to reduce incoming
transmissions from other users on the channel.
NOTE: If you are using a privacy code, both radios must be tuned to the
same channel and privacy code to communicate. Each channel will
remember the last privacy code you selected.
To Select a Privacy Code:
1. After selecting a channel, press and release the MODE
button until the small numbers next to the channel
number flash on the display.
2. Press the CHANNEL UP or CHANNEL DOWN button to
select a privacy code.
You can press and hold the CHANNEL UP or CHANNEL
DOWN button for fast advance through CTCSS privacy
code numbers.
3. When your desired privacy code is displayed, choose
one of the following:
a. Press the MODE button to enter the new setting
and proceed to other functions.
English
b. Press the LOCK button to enter the new setting and return to LISTENING
MODE.
c. Do not press any buttons for fifteen (15) seconds to enter the new
setting and return to LISTENING MODE.
Voice Activated Transmit (VOX)
In VOX Mode, your microTALK®radio can be used “hands-free,” automatically
transmitting when you speak. You can set the VOX sensitivity level to fit the
volume of your voice and avoid transmissions triggered by background noise.
To Turn VOX Mode On or Off:
1. Press the MODE button until the VOX icon flashes on
the display. The current On or Off setting is displayed.
2. Press the CHANNEL UP or CHANNEL DOWN button to
turn VOX On or Off.
3. When your desired VOX Mode setting is displayed,
choose one of the following:
a. Press the MODE button to enter the new setting
and proceed to other functions.
b. Press the LOCK button to enter the new setting and
return to LISTENING MODE.
c. Do not press any buttons for fifteen (15) seconds
to enter the new setting and return to LISTENING
MODE.
Mode Button
Channel Buttons
Select Privacy Code
Channel Buttons
Select VOX
Mode Button

MODE FUNCTIONS
To Set the VOX Sensitivity Level:
1. Press the MODE button until the VOX icon flashes and
the current sensitivity level is displayed.
The current sensitivity level is displayed with the letter
“L” and a number 1 to 5, 5 being the most sensitive
level and 1 being the least sensitive level.
2. Press the CHANNEL UP or CHANNEL DOWN button to
change the setting.
3. When your desired VOX sensitivity level is displayed,
choose one of the following:
a. Press the MODE button to enter the new setting
and proceed to other functions.
b. Press the LOCK button to enter the new setting and
return to LISTENING MODE.
c. Do not press any buttons for fifteen (15) seconds
to enter the new setting and return to LISTENING
MODE.
Channel Scan
Your microTALK®radio can automatically scan channels (1 to 8).
NOTE: The radio ignores specific CTCSS privacy codes while scanning
English
channels.
To Scan Channels:
1. Press the MODE button until the Scan icon and the
channel number flash on the display.
2. Press the CHANNEL UP or CHANNEL DOWN button to
begin scanning channels.
The Scan icon will continue to be displayed when channel
scan is On. Your radio will continue to scan all channels
and stop if an incoming transmission is detected. Your
radio will remain on that channel for ten (10) seconds.
While setting channel scan, if you do not press any
buttons for fifteen (15) seconds your radio will
automatically return to LISTENING MODE on the channel
or channel/privacy code displayed before you entered
Mode Functions.
During An Incoming Transmission,
You Can Choose From The Following:
a. Press and hold the TALK button to communicate on that channel. Your
radio will remain on that channel and return to LISTENING MODE.
b. Press the CHANNEL UP or CHANNEL DOWN button to resume scanning
channels.
Channel Buttons
Select VOX
Sensitivity Level
Mode Button
Mode Button
Channel Buttons
Select Scan Channels

MODE FUNCTIONS
If you press the TALK button while scanning and not within ten (10) seconds
of receiving a transmission, you will transmit on the channel on which you
last received a transmission. This will return the radio to LISTENING MODE.
If you do not press any button within ten (10) seconds, your radio will
automatically resume scanning channels.
During Scanning (while not receiving a transmission),
You Can Choose From The Following:
a. Press and hold the TALK button to communicate on either the channel
or channel/privacy code that was displayed before you entered Mode
Functions or the channel on which, during scanning, you last received a
transmission. This will return the radio to LISTENING MODE.
b. Press the MODE button to proceed to set CTCSS privacy code on the
channel that was either displayed before you entered Mode Functions
or on which, during scanning, you last received a transmission (see
“CTCSS Privacy Code Scan” for further details).
c. Press the LOCK button to return to LISTENING MODE on either the
channel or channel/privacy code that was displayed before you entered
Mode Functions or the channel on which, during scanning, you last
transmitted or received.
English
CTCSS Privacy Code Scan
Your microTALK®radio can automatically scan the CTCSS
privacy codes (01 to 38) within one (1) channel.
To Scan Privacy Codes:
1. While in LISTENING MODE, press the CHANNEL UP or
CHANNEL DOWN button to choose the channel on
which you wish to scan the CTCSS privacy codes.
2. Press the MODE button until the Scan icon and the
small numbers next to the channel number flash on
the display.
3. Press the CHANNEL UP or CHANNEL DOWN button to
begin scanning CTCSS privacy codes within the
channel you selected.
The Scan icon will continue to be displayed when CTCSS
privacy code scan is On. Your radio will continue to scan
CTCSS privacy codes and stop as an incoming
transmission is detected. Your radio will remain on that
channel/privacy code for ten (10) seconds.
While setting CTCSS privacy code scan, if you do not
press any buttons for fifteen (15) seconds your radio will
automatically return to LISTENING MODE on the
channel/privacy code that was displayed before you entered Mode Functions.
Select Scan Privacy
Codes
Mode Button
Channel Buttons
Select Channel

MODE FUNCTIONS
During An Incoming Transmission,
You Can Choose From The Following:
a. Press and hold the TALK button to communicate on that
channel/privacy code. Your radio will remain on that channel/privacy
code and return to LISTENING MODE.
b. Press the CHANNEL UP or CHANNEL DOWN button to resume scanning
CTCSS privacy codes.
If you press the TALK button while scanning and not within ten (10) seconds
of receiving a transmission, you will transmit on the channel/privacy code on
which you last received a transmission. This will return the radio to LISTENING
MODE.
If you do not press any button within ten (10) seconds, your radio will
automatically resume scanning CTCSS privacy codes.
During Scanning (while not receiving a transmission),
You Can Choose From The Following:
a. Press and hold the TALK button to communicate on either the channel
or channel/privacy code that was displayed before you entered Mode
Functions or channel/privacy code on which, during scanning, you last
received a transmission. This will return the radio to LISTENING MODE.
b. Press the MODE button to proceed to next available Mode Function.
English
c. Press the LOCK button to return to LISTENING MODE on either the
channel or channel/privacy code that was displayed before you entered
Mode Functions or the channel/privacy code on which, during scanning,
you last received a transmission.
VibrAlert®and Call Alert
Your microTALK®radio can alert you to incoming signals by sounding an
audible call tone, by vibrating silently, or both.
To Change Call Settings:
1. Press the MODE button until the
Call Setting icon flashes on the
display. The current setting (“01”
– Vibrate + Ring, “02” – Vibrate
Only, or “00” – Ring Only) is
displayed.
2. Press the CHANNEL UP or
CHANNEL DOWN button to change
the call setting.
VibrAlert®Icon
VibrAlert®&
Call Alert Icon
Call Alert Icon
Mode Button
Channel Buttons

MODE FUNCTIONS
3. When your desired call setting is displayed:
a. Press the MODE button to enter the new setting and proceed to other
functions.
b. Press the LOCK button to enter the new setting and return to LISTENING
MODE.
c. Do not press any buttons for fifteen (15) seconds to enter the new
setting and return to LISTENING MODE.
Baby Monitor
With the Baby Monitor Function on, a radio left near a baby will transmit to
another unit on the same channel and privacy code whenever a sound is
detected. Baby Monitor uses the same sensitivity level you set for the VOX
Function. If you have not set a VOX sensitivity level (see the “Voice Activated
Transmit [VOX]” section of this manual), the maximum sensitivity level 5 will
automatically be used.
To Turn Baby Monitor On:
1. Press MODE button until the Baby Monitor icon flashes
on the display. The current Off setting is displayed.
2. Press the CHANNEL UP or CHANNEL DOWN button to
change the setting to On.
3. Press the LOCK button to enter the On setting and
English
enter BABY MONITOR MODE.
NOTES: Pressing the MODE button will enter the Baby
Monitor Mode setting as Off and proceed to other
Mode Functions.
Not pressing any buttons for fifteen (15) seconds
will enter the Baby Monitor Mode setting as Off
and return the radio to LISTENING MODE.
NOTE: Both radios must be tuned to the same channel
and privacy code to communicate.
To Terminate Baby Monitor Mode:
1. Choose one of the following:
a. Press the TALK button and return to LISTENING
MODE.
b. Press the LOCK button and return to LISTENING MODE.
c. Press the MODE button and proceed to the next available Mode
Function.
Mode Button
Lock Button
Channel Buttons
Select Baby Monitor

MODE FUNCTIONS
Dual Watch
Dual Watch allows you to simultaneously monitor any two (2) Dual Watch
Locations:
Dual Watch Location 1 – is always the channel/privacy code displayed
before you entered Mode Functions. See “Channels” and “CTCSS
Privacy Codes” sections for further details.
Dual Watch Location 2 – will be stored in the radio. It can be edited
and/or recalled for future engagements of Dual Watch Mode.
To Program Or Edit Dual Watch Location 2 And
Engage Dual Watch Mode:
1. Press the MODE button until the Dual Watch icon and
the channel number flash on the display.
2. Choose one of the following:
a. Select or edit a channel:
1) Press the CHANNEL UP or CHANNEL DOWN
button to select a channel (1 to 8).
b. Select or edit a channel/privacy code:
1) Press the CHANNEL UP or CHANNEL DOWN
button to select a channel (1 to 8).
2) Press the MODE button to set the channel. The
English
small numbers next to the channel number will
flash on the display.
3) Press the CHANNEL UP or CHANNEL DOWN
button to select a CTCSS privacy code
(00 to 38).
3. Press the LOCK button to set Dual Watch Location 2
and engage DUAL WATCH MODE (see below for
further details).
NOTES: To terminate Dual Watch and proceed to the next available Mode
Function, press the MODE button.
While setting Dual Watch Location 2, if you do not press any buttons
for fifteen (15) seconds your radio will automatically return to
LISTENING MODE on Dual Watch Location 1.
Select Dual Watch
Mode Button
Channel Buttons
Lock Button

MODE FUNCTIONS
To Turn Dual Watch On:
NOTE: Dual Watch Location 2 must be programmed to
turn Dual Watch on.
1. Set the first Dual Watch Location (channel/privacy
code) you wish to monitor (see “Channels” and
“CTCSS Privacy Codes” sections for further details).
2. Press the MODE button until the Dual Watch icon and
the channel number flash on the display.
NOTE: While setting Dual Watch, if you do not press any
buttons for fifteen (15) seconds your radio will
automatically return to LISTENING MODE on the
last channel or channel/privacy code displayed
before you entered Mode Functions.
3. Press the LOCK button to engage DUAL WATCH MODE.
During An Incoming Transmission,
You Can Choose From The Following:
a. Press and hold the TALK button to communicate on that Dual Watch
Location. Your radio will remain on that Dual Watch Location and return
to LISTENING MODE.
b. Press the CHANNEL UP or CHANNEL DOWN button to resume Dual
English
Watch.
If you press the TALK button while in Dual Watch and not within ten (10)
seconds of receiving a transmission, you will transmit on the last Dual Watch
Location on which you received a transmission. This will return the radio to
LISTENING MODE.
If you do not press any button within ten (10) seconds, your radio will
automatically resume Dual Watch.
During Dual Watch (while not receiving a transmission),
You Can Choose From The Following:
a. Press and hold the TALK button to communicate on either Dual Watch
Location 1 or the last Dual Watch Location on which, during Dual
Watch, you last received a transmission. This will return the radio to
LISTENING MODE.
b. Press the MODE button to proceed to other functions.
c. Press the LOCK button to return to LISTENING MODE on either Dual
Watch Location 1 or the last Dual Watch Location on which, during Dual
Watch, you last received a transmission.
Mode Button
Select Channel
Lock Button

MODE FUNCTIONS
To terminate Dual Watch:
1. Choose one of the following:
a. Press the LOCK button to return to LISTENING MODE on either Dual
Watch Location 1 or the last Dual Watch Location on which, during Dual
Watch, you last received a transmission.
b. Press the TALK button to return to LISTENING MODE on either Dual
Watch Location 1 or the last Dual Watch Location on which, during Dual
Watch, you last received a transmission.
c. Press the MODE button and proceed to the next available Mode
Function.
English
5 Call Tone Settings
You can choose between five (5) different call tone settings to transmit a
unique call alert.
To Change a Call Tone Setting:
1. Press the MODE button until the letter “C” and the
current call tone number (1 to 5) is displayed. The
current call tone will sound for two (2) seconds.
2. Press the CHANNEL UP or CHANNEL DOWN button to
hear the other call tone settings.
3. When your desired call tone setting is displayed,
choose one of the following:
a. Press the MODE button to enter the new setting
and proceed to other functions.
b. Press the LOCK button to enter the new setting and
return to LISTENING MODE.
c. Do not press any buttons for fifteen (15) seconds
to enter the new setting and return to LISTENING
MODE.
Call Tone Setting
Mode Button
Channel Buttons

MODE FUNCTIONS
"Roger Beep" Confirmation Tone
Your listener will hear an audible tone when you release the TALK button. This
alerts the other party that you have finished talking and that it is OK for them
to speak.
To Turn “Roger Beep” On or Off:
When you turn On your microTALK®radio for the first
time, “Roger Beep” will be On.
1. Press and release the MODE button until the “Roger
Beep” icon flashes on the display. The current On or
Off setting is displayed.
2. Press the CHANNEL UP or CHANNEL DOWN button to
select “Roger Beep” On or Off.
3. When your desired Roger Beep Mode setting is
displayed, choose one of the following:
a. Press the MODE button to enter the new setting
and proceed to other functions.
b. Press the LOCK button to enter the new setting and
return to LISTENING MODE.
c. Do not press any buttons for fifteen (15) seconds
to enter the new setting and return to LISTENING MODE.
English
Keystroke Tones
With Keystroke Tones turned On, your radio will sound beeps each time you
press a button or change a setting.
To Turn Keystroke Tones On or Off:
When you turn On your microTALK®radio for the first
time, Keystroke Tones will be On.
1. Press the MODE button until the Keystroke Tones icon
flashes on the display. The current ON or OFF setting
is displayed.
2. Press the CHANNEL UP or CHANNEL DOWN button to
turn Keystroke Tones On or Off.
3. When your desired Keystroke Tone Mode setting is
displayed, choose one of the following:
a. Press the MODE button to enter the new setting
and return to LISTENING MODE.
b. Press the LOCK button to enter the new setting and
return to LISTENING MODE.
c. Do not press any buttons for fifteen (15) seconds
to enter the new setting and return to LISTENING
MODE.
Select Keystroke
Mode Button
Channel Buttons
Select Roger Beep
Mode Button
Channel Buttons

D.O.C., OPTIONAL ACCESSORIES,
WARRANTY & CUSTOMER SERVICE
Declaration of Conformity
This declaration is the responsibility of the manufacturer/importer
Cobra Electronics Europe Limited
Dungar House
Northumberland Avenue
Dun Laoghaire
County Dublin, Ireland
Date: October 29, 2003
This certifies that the following designated product
PRIVATE MOBILE RADIO: MT 725
(Product Identification)
complies with the essential protection requirements of R & TTE Directive 1999/5/EC on the approximation of
the laws of the Member States relating to Radio Spectrum Matters, EMC and Electrical Safety.
This declaration applies to all specimens manufactured in accordance with the attached technical documentation
described in Annex II of the Directive which forms part of this declaration.
Assessment of compliance of the product (class 2.6) with the requirements relating to the essential
requirements according to Article 3 R & TTE was based on Annex IV of Directive 1999/5/EC and the following
standards:
Radio Spectrum: EN 300 296-2 v.1.1.1 (02/01)
(Identification of regulations/standards)
EMC: EN 301 489-5 (07/2000)
(Identification of regulations/standards)
Electrical Safety: EN 60065: 1998
(Identification of regulations/standards)
RF Exposure: EN 50371: 2002
(Identification of regulations/standards)
DUBLIN, IRELANDMIKE KAVANAGH
English
Optional Accessories
For accessory orders and availability, please contact
your local dealer.
PA-BC1 Replacement Belt Clip
FA-BP NiMH Rechargeable
Battery Pack
PA-CW Rapid Wall Mount Charger
(220 V, 2-pin CE plug and
240 V, 3-pin UK plug adapter)
MA-SM Lapel Speaker/Microphone
MA-VOX VOX Headset Speaker/Microphone
MA-EBM Ear Bud Microphone
with Push To Talk Button
Warranty &
Customer Service
For warranty and customer service information, please
contact your local dealer.
PA-BC1
FA-BP
PA-CW
MA-SM
MA-VOX
MA-EBM
For use in EU countries, subject to local laws and regulations.
CEEL™ is a trademark of Cobra Electronics Corporation, USA.
Snake design and microTALK® are registered trademarks of Cobra Electronics Corporation, USA.
©2003 Cobra® Electronics Europe Limited
Dungar House, Northumberland Avenue
Dun Laoghaire, County Dublin, Ireland
www.cobra.com