CoCo AWMR-230 User manual

USER’S MANUAL
version 1.1
English
AWMR-230 MINI BUILT-IN SWITCH

AWMR-230 MINI BUILT-IN SWITCH
*
C
B
A
D
A: Search mode button
B: Wall switch connection
C: Light connection
D: Indicator (power and connection status)
* Picture of the AYCT-102 (not
included)
1

AWMR-230 MINI BUILT-IN SWITCH
2
[1] Switch off the mains power. [2] Remove the existing switch from the wall.

AWMR-230 MINI BUILT-IN SWITCH
[3] Disconnect the 2 power wires (brown and
black) from the wall switch.
230 VAC
[4] Connect the 2 switch wires from the built-in
switch to the terminals on the wall switch from
which you disconnected the wires. It does not
matter which wire is connected to which terminal.
Your wire colours may be different!
3

AWMR-230 MINI BUILT-IN SWITCH
4
[5] Connect the wires you disconnected previously
to the built-in switch: [1] L: ‘Hot wire’ (brown, from
the central junction box), [2] : ‘Switch wire’
(black, from the light). Push the built-in switch into
the wall box.
2
1
230 VAC
[6] Switch on the mains power.
The indicator on the built-in switch remains lit
as long as there is power on the circuit!
The built-in switch is normally off. It can only be
switched on once a connection is established to a
transmitter [7– 8]!
If in doubt or if the wire colours are different,
ask your installer!
The total load must not exceed 230 Watts!

AWMR-230 MINI BUILT-IN SWITCH
5
[7] Press the search mode button with a pointed
object. The indicator begins to flash.
[8] Send an ‘on’ signal with your transmitter. Press
the desired ‘on’ button of a remote control or wall
switch. The indicator on the built-in switch stops
flashing as soon as the connection is made.
There is now power on the wires. Make sure
you do not touch any exposed wiring!
If no connection is made with a transmitter after
15 seconds, the search mode ends automatically.
Repeat [7] to activate the search mode if
necessary!

AWMR-230 MINI BUILT-IN SWITCH
6
[9] To confirm, the built-in switch switches on and
off two times. The code of the transmitter is stored
in the memory of the built-in switch.
[10] Re-install the wall switch in the wall box (in
which the built-in switch is located). The product is
ready for use.
You can continue to use the wall switch
manually.
The codes remain in the memory of the switch,
even if there is a power failure!
A maximum of 6 different transmitter codes can
be stored simultaneously!

AWMR-230 MINI BUILT-IN SWITCH
Remarks
Reminders
• The product is suitable for installation in a wall box, behind the (existing) wall switch, and must be used
in combination with one COCO transmitter.
• The wall box must have a depth of at least 40 mm.
• The product is a switch/receiver: remotely controls lighting (or other suitable equipment), without
complex wiring. You can continue to use the existing wall switch manually.
• To prevent interference between devices, avoid placing multiple products close to each other. The
minimum distance between units should be approx. 50 cm.
• The wireless system can be indefinitely expanded with other COCO remote controls and/or receivers.
• Your COCO transmitter may have a special ‘group’ button with which multiple receivers with different
settings can nonetheless be controlled simultaneously. Repeat [7 - 8] and press the ‘group’ on button of
the transmitter in step [8].
• To delete one set code: (1) Press the search mode button briefly. (2) Press the ‘off’ button of the code
you want to delete from the memory. (3) To confirm, the built-in dimmer switches on and off two times.
• To delete all the set codes (resetting the memory): (1) Hold in the search mode button. (2) The indicator
begins flashing after approx. 7 seconds. (3) Release the button. (4) Press the search mode button
again. (5) To confirm, the built-in dimmer switches on and off two times.
• If the product does not work:
- Reset the memory (see previous line) and set the code in the transmitter again (repeat [7 - 9]).
Check whether the indicator is lit; if not, there may be no power to the product or the electronic fuse in
the product may have blown (in the latter case the product must be replaced).
Safety instructions
• Wa rning: Even if the product is switched off, voltage may still be present at the switched socket!
• Never use COCO products for life support systems or other applications in which equipment
malfunctions can have life-threatening consequences.
• Do not connect any lights or other devices that consume more than 230 Watts. Connecting incorrect
equipment can cause defects, a short circuit and fire.
7

AWMR-230 MINI BUILT-IN SWITCH
8
• This product is equipped with an electronic fuse that interrupts the power in the event of a short circuit,
overload (more than 2 A) or when the temperature exceeds 130 °C. If this occurs, the product must be
replaced. A defective electronic fuse is not covered by the warranty.
• Do not expose this product to excessive heat, direct sunlight or moisture.
• Do not attempt to repair this product. If the product is damaged or if you are in doubt about the proper
operation, take the product back to the place of purchase.
• Do not use the product in damp areas. Clean the device with a dry cloth.
Wireless
• This product works using a radio signal that passes through walls, windows and doors. The range is
maximum 75 metres in the open air. The range indoors is strongly influenced by local conditions such
as concrete, glass and metals. On average, the indoor range is approximately 30 metres.
• New double glass often includes a thin metallic layer. This type of glazing (“HR glass”) allows most
visible light to pass through but has a negative impact on radio signals. If there is HR glass between the
transmitter and receiver, you should expect a significant reduction of the range of the wireless signal.
• This product operates at a frequency of 433.92 MHz. It complies with the essential requirements and
other conditions of R&TTE Directive 1999/5/EC and can be used in all EU countries.
• There may be restrictions on the use of this device outside the EU. If this device is used outside the EU,
check whether the device complies with the local directives.
This product complies with the essential requirements and other relevant provisions of the applicable
European directives. The Declaration of Conformity (DoC) is available at www.coco-technology.com.

AWMR-230 MINI BUILT-IN SWITCH
If possible, submit this product for recycling after use. Do not dispose of the product with household trash.
Warranty and copyright
This device is covered by a two-year warranty that begins on the day of purchase. Visit www.coco-
technology.com/warranty for additional information. Reprinting of (portions of) this manual without
permission from Pan-Trade International B.V. is expressly prohibited.
9

AWMR-230 MINI BUILT-IN SWITCH
10
PAN-TRADE INTERNATIONAL B.V.
P.O. BOX 126
4760 AC ZEVENBERGEN
THE NETHERLANDS
www.coco-technology.com
Declaration of Conformity
Pan-Trade International BV declares that the COCO product, model:
type designation AWMR-230 MINI BUILT-IN SWITCH
item number 74035
is in compliance with the essential requirements and other relevant provisions of directives R&TTE
1999/5/EC, EMC 2004/108/EC and LVD 2006/95/EC and is compatible with the standards EN 300 220-
1/3, EN 55015, EN 301 489-1/3 and EN 60950.
Manufacturer / Authorised representative,
M.A. Hoekstra, managing director
Zevenbergen, 2008-01-30