cogeco RC3394003/01BR User manual

User guide for Remote Control RC3394003/01BR
The remote control has been programmed to control your set-top box and can be
programmed to control your TV.
Installing Batteries
The remote requires 2xAAA batteries. A diagram inside the battery compartment of the
remote indicates proper placement of the batteries. When batteries are properly
installed, the light on the remote blinks each time a key is pressed
Know your Remote
The diagram below describes each key on your remote control. Functions may vary
between different services. Refer to the user guide for your set-top box for descriptions
of specific functions.

Product Introduction
1) This RCU is transmitting IR and RF. There is a simple set up feature for TV/Home
Theatre device.
2) The RCU can be set-up to control a RF or an IR STB (mutually exclusive).
3) The RF platform is BLE, using HOGP as the top layer.
Before the RCU can control the STB, the RCU must pair with the STB first.

4) The IR protocol to control the STB is NEC. When RCU is not connected to any STB via
BLE, MCU use IR to control STB.
5) When BLE is not connected, all the STB IR keys are transmitted through NEC IR
protocol.
Custom ID is 0x1620.
Set STB Control Medium
1) Set to IR Mode:
Press <<MENU + 1>> simultaneously for 3 seconds.
2) Set to RF Mode:
Press <<MENU + 2>> simultaneously for 3 seconds;
3) Set dual-function Keys as TV Keys
Press << OK + 3>> simultaneously for 3 seconds;
4). Set Volume Keys as TV Keys:
Press <<MENU + 3>> simultaneously for 3 seconds.
5). Set dual-function Keys as STB Keys:
Press <<MENU + 4>> simultaneously for 3 seconds.
Voice Function
1) Press and released <Google Assistant> key to open the voice function, RCU will close
the voice function after receiving the stop command sent by the host.
2)When RCU is recording, the STB-LED is always on.
OTA
The RCU software supports upgrade via OTA (Over-The-Air).
From diagram above, the STB can transfer the RCU firmware by the BLE link.

The OTA process can be triggered by the user using the RCU or by the STB itself.
The RCU OTA IMAGE need to be downloaded into the STB itself. After the OTA is
completed, the RCU will have a new firmware.
Simple Setup
1) Simple Setup is a feature helps user to automatically set up the remote control via
STB.
After being set by Simple Setup, the RCU will be able to control TV/AMP.
2) Below IR function could be configured to control TV through simple setup:
TV Power, TV input, TV Mute, TV Vol+and TV vol-.
3) After a successful simple setup for TV, RCU will automatically set dual-function keys
into TV mode
Battery Voltage Monitor
LVD check will be triggered after a signal key is released in user mode.
1.When the LVD is detected (battery voltage<2.3V);
2. While RCU works in BLE mode, it supports Bluetooth standard service of battery level
notification. The paired host is then able to get battery level of the RCU.
Sleeping Mode
When no any activity need to do, the RC enters sleeping for power saving purpose. The
sleeping
mode behaves as below:
1) All LEDs are off.
2) IR and RF communications are stopped.
3) Any key press will wake up the RC.

FCC ID:2AGOFRC339A
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Attention that changes or modification not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This product has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
product generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this product does cause harmful i nterference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils
radioexempts de licence. L'exploitation est autorisée aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si
le brouillage est susceptible d'en compromettre le fonctionnement.
Under Industry Canada regulations, this radio transmitter may only operate using an
antenna of a type and maximum (or lesser) gain approved for the transmitter by
Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.)
is not more than that necessary for successful communication.
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut
fonctionner avec une antenne d'un type et d'un gain maximal (ou inférieur) approuvé
pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son
gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas
l'intensité nécessaire à l'établissement d'une communication satisfaisante.