Coilhose Pneumatics IN-LINE Series User manual

90-416* (revised 12/06)
Questions regarding this form
should be directed to one of the
following:
East/Central: 732-390-8480 (NJ)
West: 503-434-5964 (OR)
E-mail: [email protected]
IN-LINE SERIES LUBRICATORS
Installation and Operating Instructions
Model 40014 and 40038
Maximum Supply Pressure: . . . . . . .150 PSI
Maximum Operating Temperature: .250° F
Material:
Body . . . . . . . . . . . . . . . . . . . . .Anodized aluminum
Fill Cap . . . . . . . . . . . . . . . . . . .Brass
Capacity: . . . . . . . . . . . . . . . . . . . . .5 cc
40014 40038
Length: . . . . . . . . . . . . . . . . . . . . . . .3.09" . . . . . . . . . . .3.12"
Height: . . . . . . . . . . . . . . . . . . . . . . .1.38" . . . . . . . . . . .1.38"
Weight: . . . . . . . . . . . . . . . . . . . . . . .5 oz. . . . . . . . . . . .5.5 oz
Inlet: . . . . . . . . . . . . . . . . . . . . . . . . .1/4" FPT . . . . . . . .3/8" FPT
Outlet: . . . . . . . . . . . . . . . . . . . . . . .1/4" MPT . . . . . . . .3/8" MPT
Model 40024
Maximum Supply Pressure: . . . . . . .150 PSI
Maximum Operating Temperature: .120° F
Material:
Body . . . . . . . . . . . . . . . . . . . . .Die-cast zinc
Bowl . . . . . . . . . . . . . . . . . . . . . .Polycarbonate
Capacity: . . . . . . . . . . . . . . . . . . . . .4 cc
Length: . . . . . . . . . . . . . . . . . . . . . . .2.35"
Diameter: . . . . . . . . . . . . . . . . . . . . .1 1/3"
Weight: . . . . . . . . . . . . . . . . . . . . . . .2 oz.
Inlet: . . . . . . . . . . . . . . . . . . . . . . . . .1/4" FPT
Outlet: . . . . . . . . . . . . . . . . . . . . . . .1/4" MPT
Model 50014 and 50038
Maximum Supply Pressure: . . . . . . .150 PSI
Maximum Operating Temperature: .250° F
Material:
Body . . . . . . . . . . . . . . . . . . . . .Anodized aluminum
Fill Cap . . . . . . . . . . . . . . . . . . .Brass
Capacity: . . . . . . . . . . . . . . . . . . . . .7.5 cc
50014 50038
Length: . . . . . . . . . . . . . . . . . . . . . . .3.25" . . . . . . . . . . .3.28"
Height: . . . . . . . . . . . . . . . . . . . . . . .2" . . . . . . . . . . . . . .2"
Weight: . . . . . . . . . . . . . . . . . . . . . . .5.9 oz. . . . . . . . . . .6.4 oz
Inlet: . . . . . . . . . . . . . . . . . . . . . . . . .1/4" FPT . . . . . . . .3/8" FPT
Outlet: . . . . . . . . . . . . . . . . . . . . . . .1/4" MPT . . . . . . . .3/8" MPT
A
C
B
AC
B
A
C
B

East/Central: 19 Kimberly Road • East Brunswick, NJ 08816 • Phone: [phone] / Fax: [phone]
West: 1730 NE Miller Street • McMinnville, OR 97128 • Phone: [phone] / Fax: [phone]
Cleaning:
Coilhose In-Line Lubricators will provide long periods of uninterrupted service, provided the air and the oil supply are
kept clean. Periodic cleaning is recommended.
To remove and clean the lubricator:
1. Depressurize line and disconnect the lubricator from the air supply.
2. Slowly remove oil fill cap to relieve pressure in oil reservoir and then drain the oil. Caution: If pressure is released too
quickly, oil may spray from reservoir.
3. Remove lubricator from air tool.
4. "Back flush" lubricator to blow out any dirt or residue.
5. Clean lubricator with warm water and household detergent or mild commercial-grade solvent.
6. Make sure all moisture is removed by thoroughly blowing out the unit with compressed air.
7. Follow "Installation and Filling" instructions below to reinstall lubricator.
Installation and Filling:
1. Apply a small amount of thread sealant compound to the lubricator male threads (B).
2. Hand tighten male connector into female inlet of the air tool.
NOTE: Adding a 6" snubber (whip hose) between the air tool and lubricator will provide a safer and longer lasting
installation.
3. Hand tighten male air supply outlet of lubricator into female inlet of the lubricator (C).
4. Wrench tighten both connections until air tight seals are formed.
5. Remove oil fill cap (A) and fill reservoir with lubricant, leaving a small amount of space for air.
6. Replace and tighten oil fill cap until air tight.
7. Connect air supply.
8. Activate air tool several times to set needle valve into action.
Caution: Do not use synthetic oil.
Detergent oil, antifreeze fluid, and machine oil heavier than SAE # 40 (S.U.V. 800 S.E.C. at 100° F) should not be used.
For applications with temperatures above 40° F, we recommend the use of Coilhose non-detergent ATL rust-proofing
lubricant; for applications with temperatures between - 40° F and 40° F, we recommend the use of Coilhose ATLW
lubricant.
Caution: Do not exceed 150 PSI Inlet pressure.