Colornite Moving Spot 60E User manual

Moving Spot 60E
LED Beam Moving Head
User Manual

1.1 Unpacking
1.2 Safety Instructions
Carefully unpack the carton, check the contents to ensure that all parts are present,
and have been received in good condition. Contact your supplier immediately and
retain packing material for inspection if any part is missing or damaged.
1. INTRODUCTION
■1 x Moving Spot 60E
■1 x Power Cord
■1 x Mounting bracket
■1 x User Manual
▪The product is for indoor use only.
▪Always turn off, unplug power and allow fixture to cool before servicing.
▪Ensure that fixture is properly grounded.
▪Please keep this User Guide for future consultation.
▪Always make sure that you are connecting to the proper voltage and that the line
voltage you are connecting to is not higher than that stated on decal or rear panel of
the fixture.
▪Always disconnect from power before servicing or replacing fuse.
▪Make sure power cord is never crimped or damaged.
!
Warning!!! To reduce the risk of fire, electric shock, or injury to persons,
follow these important safety instructions:
The following items are included in the box:
Caution!
Avaid looking directly into the LED light beam at a close distance!
1
Thank you for selecting this LED Moving Head Spot. It has 1 color wheel, 1 rotating
gobo wheel, 1 3-facet prism and motorized focus functions. With a 60W White LED
as light source, it is great for stage, club, bar, DJ, etc. To optimize the performance
of this product, please read the user manual carefully before use.
1.3 Features
▪60W LED moving head spot
▪DMX, Auto, Sound, M/S
▪8/16 DMX channels
▪1 color wheel: 7 colors + white

The Moving Head is fully operational in any mounting position, hanging upside-down,
side mounted, or set on a flat llevel surface, etc.
1.4 Product overview
2. SETUP
2.1 Mounting
▪1 gobo wheel: 7 gobos + open
▪1 3-facet prism, rotating at variable speed
▪Motorized focus
▪Electronic strobe 1-25 fps
▪Dimmer 0-100%
▪Pan/Tilt: 540° / 270°, automatic correction
▪PowerCon In & Out
▪4-button LCD display
2
IMPORTANT!!! Safety cables must always be used when unit is celling or truss
mounted. The safety cable must be capable of holding 10 times the weight of the
fixture.
Control Panel
Power In/Out ON/OFF
Fuse
DMX In/Out
The fixture is designed to work on AC 100-240V 50-60Hz. All units must be powered
directly from a switched circuit. This unit cannot be run on a rheostat or dimmer
circuit even if used solely for a 0% to 100% switching.
2.3 AC Power
WARNING!!! All fixtures must be connected to circuits with a
suitable Earth Ground.

3.1 Menu Map
3. OPERATION INSTRUCTIONS
3
DMX Address DMX Address = 0001
Display Reverse
Operating Mode
Language Setting
Advanced Setting
YES
YES
DMX 15 ch
DMX 6 ch Auto Program 1
Auto Program 2
Auto Program 3
Auto Program 4
Auto Program 5
Auto Program 6
Auto Program 7
Auto Program 8
Auto
Sound YES
Slave YES
English YES简体中文
Pan Reverse
Tilt Reverse
Factory Default
Home Position
Mic. Sensitivity
Tilt
Pan
Password xxx (018)
Dimmer
Color
Rotation Gobo
Focus
000-100 -128 ~ +127
-128 ~ +127
-128 ~ +127
-128 ~ +127
-128 ~ +127
-128 ~ +127
Current Mode
Temperature
Software Version
E60-V1.06
Current Time
Total Time
P/T Speed
Dimmer
Strobe
Color
Gobo
Gobo Rotation
Focus
Prism
Pan 000 - 255
000 - 255
000 - 255
000 - 255
000 - 255
000 - 255
000 - 255
000 - 255
000 - 255
000 - 255
Tilt
System Info
Manual Control

3.2 DMX channels
4
8 DMX Channels
Channel
1
2
Pan 000-255
000-255 Tilt movement
000-255
000-004
168-207
208-247
Tilt
3
4
Dimmer
Strobe
6
Color&Gobo Speed
Color & Gobo Speed from slow to fast
000-255
DMX Value Functions
Pan movement
Dimmer 0-100%
Strobe closed
005-250 Strobe from slow to fast
Strobe open
248-255 Color & Gobo changing to sound
No fucntion
Color & Gobo Macro 1
Color & Gobo Macro 2
Color & Gobo Macro 4
Color & Gobo Macro 5
Color & Gobo Macro 6
251-255
5
7
Color & Gobo
Macros
Movement Macros
000-007
008-047
048-087
128-167
Color & Gobo Macro 3
088-127
111-136
137-162
163-188
189-214
215-240
241-255
No fucntion
Movement macro 1
Movement macro 2
Movement macro 3
Movement macro 4
Movement macro 5
Movement macro 6
Movement macro 7
Movement macro 8
Movement macro 9
Movement to Sound
000-007
008-032
033-058
085-110
059-084
8 Reset
250-255 6 seconds to reset

16 DMX Channels
14 Color&Gobo Speed
Color & Gobo Speed from slow to fast
000-255
168-207
208-247
248-255 Color & Gobo changing to sound
Color & Gobo Macro 1
Color & Gobo Macro 2
Color & Gobo Macro 4
Color & Gobo Macro 5
Color & Gobo Macro 6
Color & Gobo
Macros
008-047
048-087
128-167 Color & Gobo Macro 3
088-127
15 Movement Macros
111-136
137-162
163-188
189-214
215-240
241-255
No fucntion
Movement 1
Movement 2
Movement 3
Movement 4
Movement 5
Movement 6
Movement 7
Movement 8
Movement 9
Movement to Sound
000-007
008-032
033-058
085-110
059-084
Channel
1
3
Pan 000-255
000-255 Tilt movement
000-255
000-004
041-049
050-058
Tilt
4000-255 Fine control of Tilt movement
Tilt fine
5000-255 Pan/Tilt speed from fast to slow
P/T Speed
6
7
Dimmer
Strobe
DMX Value & Functions
Pan movement
2
Pan fine
000-255 Fine control of Pan movement
Dimmer 0-100%
Strobe closed
005-250 Strobe from slow to fast
Strobe open
059-067
068-076
077-085
251-255
8Color
9Gobo
10 Gobo Rotation
11 Focus
12 Prism
13
000-004
005-013
014-022
032-040
023-031
Color2/Color3
Color3
Color3/Color4
Color4
Color4/Color5
White (Open)
White/Color1
Color1
Color2
Color1/Color2
131-139
140-195
196-199
200-255
086-094
095-103
104-112
122-130
113-121
Color8
Clockwise color scroll
Counter-clockwise
color scroll
Clockwise Gobo scroll
Counter-clockwise
Gbo scroll
Scroll stop
Color5
Color5/Color6
Color6
Color7
Color6/Color7
000-007
008-028
029-049
071-091
050-070
Open(White)
000-009 No function
000-255 Focus
010-129 Clockwise Gobo rotating from fast to slow
Counter-clockwise Gobo rotating from slow to fast
130-134 Gobo rotating stop
000-007 No function
008-134 Prism
135-255 Prism rotating from slow to fast
135-255
Gobo1
Gobo2
Gobo4
Gobo3
092-112
113-133
134-194
195-255
Gobo5
Gobo6
16 Reset 250-255 6 seconds to reset
5

5. Specifications
Source: 60W White LED
Beam angle: 13°
Power consumption: 120W maximum
Fuse: F2A / 250V
Power supply: 100~240V, 50-60Hz
Dimensions: 270 x 140 x 380 mm
Weight: 7.8 kg
6
4. General Maintenance
a. Unscrew the fuse holder and remove the damaged fuse.
b. Replace with exact same type fuse and screw the fuse holder back in its place.
4.1 Fuse Replacement
IMPORTANT INFORMATION!
In order to optimize the recovery and recycling of the materials
that old appliances contain and reduce the impact on human
health and the environment, ensure that this product is recycled
at the end of its life.