ComAp InteliVision 8 User manual

Copyright © 2017 ComAp a.s.
Written by ComAp
Prague, Czech Republic
ComAp a.s., U Uranie 1612/14a,
170 00 Prague 7, Czech Republic
Tel: [phone]
E-mail: [e-mail], www.comap-control.com Global Guide
InteliVision 8
Controller Display Unit for
ComAp Controllers
SW version 2.6.0
1 Document information 5
2 Applications overview 6
3 Fast navigation 8
4 Operator interface 21
5 Initial Screen 54
6 Features based on USB 56
7 Support of user’s pictures 63
8 Screen modification 66
9 Installation 71
10 InteliVision 8 programming 78
11 Technical data 92

InteliVision 8 2
Table of contents
1 Document information 5
1.1 Clarification of notation 5
1.2 About this guide 5
2 Applications overview 6
2.1 Firmware and PC Software Supporting InteliVision 8 6
2.2 Available Related Documentation 7
3 Fast navigation 8
3.1 IV8 front face 9
3.2 How to connect IV8 display to IGS-NT or IDcontroller? 10
3.2.1 To connect to a Controller: 10
3.2.2 Automatic detection 11
3.3 How to enter a password? 12
3.4 How to view important values? 13
3.5 How to view a controller status? 13
3.6 How to view a breaker status? 13
3.7 How to change a Gen-set mode? 14
3.8 How to change setpoints? 15
3.9 How to find alarms? 15
3.10 Communication error 16
3.11 How to change a password/to save a password/to logout? 16
3.12 How to change display brightness? 17
3.13 Main icons description 19
4 Operator interface 21
4.1 Measurement screens 25
4.1.1 IGS-NT standard measurement screens 26
4.1.2 ID measurement screens 30
4.2 Trends screen 33
4.2.1 Trends context buttons 33
4.2.2 Trends - channels 34
4.2.3 Trends - settings 36
4.2.4 Export/import of trends 37
4.2.5 Vertical markers 37
4.2.6 Scrolling by page 38
4.2.7 Availability of disk space 38
4.3 Setpoints screens 40

InteliVision 8 3
4.3.1 Change of the numerical value 41
4.3.2 Text string selection 42
4.3.3 Text string edit 43
4.4 AlarmList screen 43
4.4.1 AlarmList for IGS-NT controllers 43
4.4.2 AlarmList for ID controller 46
4.5 History screen 47
4.5.1 History context buttons 47
4.5.2 Change of an order of columns 48
4.5.3 Help/Others screen 48
4.5.4 Help context buttons 50
4.6 Rules for help customization 50
4.6.1 How it works 50
4.6.2 Text formatting rules 51
4.6.3 Other important rules 52
5 Initial Screen 54
5.1 Additional information on initial screen 54
5.2 Support of customized logo 55
6 Features based on USB 56
6.1 Directory structure and names of files 56
6.2 Export of history 57
6.3 Export/import of trends 58
6.3.1 Continuously saving of trends 58
6.3.2 Single export of trends 59
6.3.3 Import of TRD file 60
6.4 Export of archive and InteliVision 8 firmware 60
6.5 USB as “login key” 61
7 Support of user’s pictures 63
8 Screen modification 66
8.1 User definable SoftKeys buttons 66
8.2 Support of color palette 68
8.3 Transparency attribute 69
8.4 Support of Tier 4 Final symbols 70
9 Installation 71
9.1 Terminals and dimensions 71
9.2 Mounting system 72

InteliVision 8 4
9.3 Recommended wiring 72
9.3.1 ID-Mobile wiring 74
9.4 Modules’ address combination on CAN (IG/IS-NT,ID) 75
9.4.1 IGS-NT controllers and 4 InteliVisions 8 on CAN2 76
9.4.2 ID-DCU Marine controller and up to 8 InteliVisions 8 on CAN2 76
10 InteliVision 8 programming 78
10.1 ActiveSync 78
10.2 Windows Mobile Device Center (WMDC) 80
10.3 IVProg running 80
10.3.1 IVProg from Genconfig 81
10.3.2 IVProg and file association 90
10.3.3 IVProg and command line 91
11 Technical data 92
11.1 Power supply 92
11.2 Operating conditions 92
11.3 Climatic, mechanical and EMC standards 92
11.4 Dimensions and weight 94
11.5 Communication interface 95
11.6 Operating system 95
11.7 LCD display 95

InteliVision 8 5
1 Document information
1.1 Clarification of notation 5
1.2 About this guide 5
1.1 Clarification of notation
Note: This type of paragraph calls readers attention to a notice or related theme.
IMPORTANT: This type of paragraph highlights a procedure, adjustment etc., which can cause a
damage or improper function of the equipment if not performed correctly and may not be clear at
first sight.
Example: This type of paragraph contains information that is used to illustrate how a specific function
works.
1.2 About this guide
InteliVision 8 is a display unit for ComAp InteliGen NT / InteliSys NT / InteliMains or InteliDrive family of
controllers. It is designed as a simple, easy to use Plug and Play solution and delivers high visibility of all engine
data, monitoring information and trend history in a bright, colorful design.
The new screen features many significant improvements from the original IS-Display including a large colour
TFT display, which helps visibility and definition for on-screen information. The control interface has also been
updated with user-friendly intuitive active buttons - giving users access to more information in less time.
InteliVision 8 also includes features based on the USB memory stick, possibility to use own pictures on the
Measurement screens, TRENDS monitoring, helping the end user to evaluate the history events easily on one
screen in HISTORY screen, etc..
The InteliVision 8cut-out size is the same as the IS-Display, so InteliVision 8can be easily used as a
replacement for (or an alternative to) IS-Display. Regardless of the size it can be also used as a replacement for
(or an alternative to) IG-Display or I-RD-CAN.
InteliVision 8 is designed to be connected to a single controller, which means that a multiple gen-set monitoring
is not possible at one time. However on CAN if InteliVision 8 is connected to more than one controller it is
possible to switch among controllers using a different communication setting in InteliVision 8. Switching time
corresponds to the time of a configuration download (from controller to InteliVision 8).

InteliVision 8 6
2 Applications overview
2.1 Firmware and PC Software Supporting InteliVision 8 6
2.2 Available Related Documentation 7
6back to Table of contents
2.1 Firmware and PC Software Supporting
InteliVision 8
Firmware - InteliVision 8 is supported from following versions:
mhx file ivp file
IS-NT 2.6
InteliVision 8
IG-NT 2.6
IM-NT 2.9
ID-DCU-Industrial 2.9
ID-Mobile-Logger 1.8
ID-Mobile 1.6
PC Software - InteliVision 8 is supported from the following versions:
PCSoftware
GenConfig 2.6
DriveConfig 3.1
Installation Packages - InteliVision 8 is supported from the following versions:
Installation Packages
IGS-NT-Install-Suite 2.6
InteliDrive-Instal-Suite 2.9

InteliVision 8 7
2.2 Available Related Documentation
PDF files Description
InteliVision8-2.6.0 ew Feature
List.pdf
New Feature List for InteliVision 8 version 2.0
http://www.comap.cz/products/detail/intelivision8/downloads/#tabs
IGS-NT-3.8.0.-New
Features.pdf
New Features List of IG/IS-NT version 3.7.0.
https://www.comap.cz/products/detail/inteligen-nt-
basebox/downloads/#tabshttps://www.comap-
control.com/products/controllers/gen-set-paralleling-controllers
IS2GAS-1.2.0.-New
Features.pdf
New Features List of IS2GAS version 1.2.0.
https://www.comap.cz/products/detail/inteligen-nt-
basebox/downloads/#tabshttps://www.comap-
control.com/products/controllers/gen-set-paralleling-controllers

InteliVision 8 8
3 Fast navigation
3.1 IV8 front face 9
3.2 How to connect IV8 display to IGS-NT or IDcontroller? 10
3.2.1 To connect to a Controller: 10
3.2.2 Automatic detection 11
3.3 How to enter a password? 12
3.4 How to view important values? 13
3.5 How to view a controller status? 13
3.6 How to view a breaker status? 13
3.7 How to change a Gen-set mode? 14
3.8 How to change setpoints? 15
3.9 How to find alarms? 15
3.10 Communication error 16
3.11 How to change a password/to save a password/to logout? 16
3.12 How to change display brightness? 17
3.13 Main icons description 19
6back to Table of contents

InteliVision 8 9
3.1 IV8 front face
This chapter provides information on how to quickly find important data. To be more familiar with InteliVision 8
menu, see Operator interface on page 21
You can see InteliVision 8 front face and layout of all its buttons and LEDs in IV8 front face (page 9)
Image 3.1 InteliVision 8 face
Buttons and LEDs
Context
buttons Selects a submenu/sub-options
Hot keys Selects main menu options
Navigation
buttons Arrows and buttons for movement + ESC and Enter button
Stop Stops the gen-set
Start Starts the gen-set
Horn reset Deactivates the horn (audible alarm)
Power Power LED indication (green = power is on)
Controller
mode
Calls controller mode menu (the mode can be changed then by appropriate
context button)
Fault reset Acknowledges faults and alarms (active only in Alarm screen)
Alarm Alarm LED indication (yellow = alarm of the first level, e.g. warning, red =
alarm of the second level, e.g. shutdown)

InteliVision 8 10
Buttons and LEDs
Engine Engine LED indication (green = the engine is running)
MCB Opens/closes MCB
GCB Opens/closes GCB
Status bar Shows permanently important values
3.2 How to connect IV8 display to IGS-NT or
IDcontroller?
InteliVision 8 can be connected to the controller via:
CAN
NT terminal
RS232/485
3.2.1 To connect to a Controller:
1. Press Help/Others button
2. Choose Communication by pressing the context button on the right
3. Use → ← to choose ID or IGS-NT Controller, see How to connect IV8 display to IGS-NT or
IDcontroller? on page 10
4. Use ↑ ↓ and Enter buttons to choose Connection Type
5. Use ↑ ↓ and Enter buttons to choose Controller address (address can be automatically detected).
6. Use ↑ ↓ and Enter buttons to choose Terminal address (address can be automatically detected).
7. Use ↓ and press to confirm the action.
Image 3.2 Communication dialog
Note: You can also use RS232 port to connect IV8 display to ID Controller or RS232/RS485 port to connect
IV8 display to IGS-NT Controller.

InteliVision 8 11
3.2.2 Automatic detection
There is implemented the function “Automatic detection of controller address” see How to connect IV8
display to IGS-NT or IDcontroller? on page 10. The feature helps you quickly find controller or terminal
address without knowledge of communication parameters of controller.
Note: It is recommended to use automatic detection only in case the communication parameters of the
controller are not available.
IMPORTANT: During detection phase, InteliVision 8 stops communicating with already connected
controller – it is switched to initialization screen – and communication with the actual controller is
lost.
It is possible to detect:
Controller address and terminal address on CAN
Terminal address on display terminal or RS485
After detection phase the first available active address of the controller is set. If you go to the list of addresses
(press Enter on item Controller Adr.), you will see green and grey numbers.
Green colour means that detected controller is active – the address is occupied with communicating
controller (it is possible to choose the address).
Grey colour means the controller was not detected. That means the address:
can be used with non-communicating controller – for example controller has set some of parameters
incorrectly
the address is not occupied with another controller
Image 3.3 Address detection

InteliVision 8 12
Terminal address
Red colour - the address is occupied
Grey colour - the address can be used (IGS-NT has 4 addresses; ID-DCU has 5 addresses)
NT terminal address
Red colour - address is occupied
Green colour - free address
For other information on how to connect IV8 display to a controller, see Installation on page 71
3.3 How to enter a password?
There are two ways how to enter a password:
Use USB stick as a “login key” – see USB as “login key” on page 61
Insert a password manually
To enter a password manually:
1. Press Help/Others button
2. Press Users/Password button
3. Use ↑ ↓ to go to Users field and press Enter
4. Use ↑ ↓ to choose a user and press Enter
5. Use ↑ ↓ to go to EnterPassword field and press Enter
6. Enter password and press Enter
7. Use ↑ ↓ and confirm the password by pressing Login button
Note: When you try to edit a locked setpoint the login dialog appears automatically.
Image 3.4 Password dialog

InteliVision 8 13
In case you are successful logged on, the icon below appears in the upper right corner.
The icon indicates that user The Best ComAp User is logged on with access level 7.
3.4 How to view important values?
No matter where you are in the menu you can see all the time important values (engine speed, power,…) in the
status bar at the bottom of the screen. see How to view important values? on page 13 is visible from each
screen.
Image 3.5 Status bar with important values
To see all the values in more detail:
1. Press Measurement button
2. Choose one of the measurement screens (e.g. Power, Mains, Gen, Synchro,...) using context buttons.
3. To go up/down through Measurement screens use ↑ ↓ buttons (even when context menu is active).
Note: You can use PgDn or PgUp buttons to display quickly context buttons from following page, when ythez
are available (context menu has to be active).
3.5 How to view a controller status?
No matter where you are in the menu you can see the status of the controller at the bottom of the screen:
Image 3.6 Controller Status
3.6 How to view a breaker status?
To view a breaker status:
Directly on breaker buttons
In block diagram in the status bar
In Power screen in block diagram
The breaker status LED diode it is possible to see directly on breaker buttons, which are placed at a left bottom
corner (in default configuration), see How to view a breaker status? on page 13

InteliVision 8 14
Image 3.7 MCB, GCB status
Where
Blue ringlet Opened
Green ringlet closed
Red circle MCB/GCB fail
The breaker status is possible to see also in block diagram in the left side of status bar.
You can also see the breaker in “Power screen”, where a block diagram of a connection type is displayed.
1. Press Measurement button
2. Press Power button (you can find it on the right). see Measurement screens on page 25. The scheme with
breaker(s) status appears.
Note: The Power button is available only for connection with IGS-NT controller.
3.7 How to change a Gen-set mode?
To change a gen-set mode:
1. Press ControllerMode button at the bottom of IV8 display. Available gen-set modes appear, e.g. TEST,
AUT, MAN, OFF.
Note: Available gen-set modes depend on the type of used application.
2. Select a mode by pressing the appropriate context button. After a while the label above ControllerMode
button will change.

InteliVision 8 15
Image 3.8 Change of mode
3.8 How to change setpoints?
To change setpoints:
1. Press Setpoints button.
2. To scroll/see all setpoints groups, use buttons to scroll menu (when context menu is active).
3. Select a setpoint group by pressing the context button on the right side of the display (e.g. Basic settings
button).
4. To select a certain setpoint use and/or ↑ ↓ buttons (when context menu is NOT active) and press
Enter. A dialog for setpoint value adjustment appears.
5. Use → ← buttons to go to the character position.
6. To change a value of the setpoint use ↑ ↓ buttons and press Enter
Note: If you insert a wrong value (which is e.g. out of range), the field colours in red.
You can find more information about setpoints in Setpoints screens (page 40)
3.9 How to find alarms?
To find alarms:
1. If they do not appear automatically, press AlarmList button.
2. To go through alarms press ↑ ↓ or buttons.
You can find more information about alarms inAlarmList screen (page 43).
Note: When a new alarm appears the AlarmList page is displayed automatically only when the actual GUI
position is Home metering screen. From the other GUI location the AlarmList button must be pressed.

InteliVision 8 16
3.10 Communication error
If some communication error occurs, the red stripe at the top of any screen appears. see Communication
error on page 16. When a communication error relating to the change of a controller address occurs, follow
instructions in chapterHow to connect IV8 display to IGS-NT or IDcontroller? (page 10) for reconnection.
Image 3.9 Communication error
When you correct the communication error, the red stripe disappears but the grey inactive icon of lost
communication stays visible. After you press IV info button on Help/Others screen the inactive icon
disappears.
3.11 How to change a password/to save a
password/to logout?
To change a controller password:
1. Log-in (see How to enter a password? on page 12)
2. Press Help/Others button
3. Press Password.
4. Use ↑ ↓ to go to Users field and press Enter.
5. Use ↑ ↓ to choose a user and press Enter.
6. Use ↑ ↓ to go to NewPassword field and press Enter.

InteliVision 8 17
7. Use → ←to go to the character position.
8. Use ↑ ↓ to change the value (numbers 1 - 9 are available) and press Enter.
9. Use ↑ ↓ to go to ChangePassword title and press Enter to confirm the password.
10. Use ↑ ↓ to go to SavePassword title and press Enter to save password to USB stick (if connected).
11. Use ↑ ↓ to go to Logout button and press Enter in case you want to logout.
Image 3.10 Logout / change / save password dialog
Note: For IGS-NT: Only the user with the highest access level is able to reset passwords of other users (not to
change passwords). And every user is able to change its own password.
Note: For ID: Only the user with the third access level is able to change passwords of other users. And every
user is able to change its own password.
3.12 How to change display brightness?
There are two brightness settings available:
Day mode
Night mode (especially for Marine application)
Quick alternation between modes can be done by 2 second pressing the ESC button.
The brightness can be adjusted in the full range of 0 % - 100 % in the both modes How to change display
brightness? (page 17),How to change display brightness? (page 17). The brightness of the display can be
increased/decreased by holding Esc button and repeated pressing ↑ ↓. See picture below:

InteliVision 8 18
Pressing ESC +PgUp buttons or ESC +PgDn buttons switches between modes, which shall be adjusted,
when dialog for changing of intensity brightness is active How to change display brightness? (page
17),How to change display brightness? (page 17).
Image 3.11 Day mode brightness setting

InteliVision 8 19
Image 3.12 Night mode brightness setting
3.13 Main icons description
Icons at the TOP of IV Display
In IGS-NT controller
Figure + "The Best ComAp User" = User name
Open green lock and = display is NOT locked; user is logged in
7 = a user has assigned access level 7
Display or setpoint is locked; user is NOT logged in (with sufficient
password level)
PageMode is On (in History or Trend screen)
Zoom 10x
Blue icon = USB stick plugged on
Bed icon = data is written to USB stick
Green icon = data is read from USBstick

InteliVision 8 20
Icons at the TOP of IV Display
A user used USB stick as "login key"
Communication is lost
Now is communication OK, but it was lost in past time
Icons at the Bottom of IV Display
Icon is shown = trends are running
Icon is NOT shown = trends are NOT running
Access lock is active = display is locked for security reasons
Remote communication (appears when any remote connection to
controller is active)
Blinking exclamation mark = a new alarm occurred. After enter of
AlarmList, the exclamation stops blinking
Blue ringlet = opened
Green circle = closed
Red circle = MCB/GCB fail