ComAp InteliVision 5 User manual
Copyright © 2016 ComAp a.s.
Written by ComAp a.s.
Prague, Czech Republic
ComAp a.s., U Uranie 1612/14a,
170 00 Prague 7, Czech Republic
Tel: +420 246 012 111
InteliVision 5
Colour 5,7" Detachable
Display Unit
SW version 2.1.0
1 General information 3
2 Changes in the version 2.1.0 4
3 Changes in the version 1.10.0 5
4 Changes in the version 1.9.0 6
5 Changes in the version 1.8.1 7
6 Changes in the version 1.8.0 8
7 Changes in the version 1.7.0 9
8 Changes in the version 1.6.0 10
9 Changes in the version 1.5.0 11
10 Changes in the version 1.4.0 12
11 Changes in the version 1.3.0 13
12 Changes in the version 1.2 14
InteliVision 5 - New Features List 3
1 General information
1.1 Version information
This document supplements the InteliVision 5 Reference Guide
1.2 Clarification of notation
Note: This type of paragraph calls readers attention to a notice or related theme.
IMPORTANT: This type of paragraph highlights a procedure, adjustment etc., which can cause a
damage or improper function of the equipment if not performed correctly and may not be clear at
first sight.
Example: This type of paragraph contains information that is used to illustrate how a specific function
works.
InteliVision 5 - New Features List 4
2 Changes in the version 2.1.0
2.1 New features
Changes related to the specific customer branch
no impact to the software
2.2 Bug fixes
Repeated message new firmware available in GenConfig
the issue is connected only with firmware IV5 1.10.0
the issue must be solved in GenConfig as well, the release of the GenConfig with the repaired issue is
planned to Q3//2018
InteliVision 5 - New Features List 5
3 Changes in the version 1.10.0
3.1 New features
Changes related to the InteliVision 5 CAN firmware only
for more information please see the InteliVision 5 CAN NFL
InteliVision 5 - New Features List 6
4 Changes in the version 1.9.0
4.1 New features
All the new features and bugfixes have been taken over from the InteliVision 5 to the InteliVision 5 CAN
display unit
there is no difference between InteliVision 5 and InteliVision 5 CAN firmwares from the software point of
view (except CAN support in InteliVision 5 CAN)
from now the InteliVision 5 and InteliVision 5 CAN firmwares will be released at the same time
Thesupport of the InteliDrive DCU Marine 3.0.0
ECU Modules subpage in Administration is added
1 upto 16 ECUs can be displayed
ECU Info item from the Administration - Controller Info subpage is moved to the new subpage ECU Modules
The Alarmlist page now supports the different GUI view of the Alarmlist page which is dedicated for the
Drive controller families
Separated GUI visual representation of the common alarms and ECU alarms
The metering screens have been slightly modificated for the InteliDrive DCU Marine 3.0.0 controller
there is a metering screens differences between InteliDrive DCU Marine 3.0.0 controller and older
archive version
4.2 Bug fixes
Unpredictible behaviour of the setpoint listing on the InteliVision 5 display unit when the controller
configuration has more than 512 parameters in all the groups (entirely).
InteliVision 5 - New Features List 7
5 Changes in the version 1.8.1
5.1 Bug fixes
Unpredictible behaviour of the setpoint listing on the InteliVision 5 display unit when the controller
configuration has more than 512 parameters in all the groups (entirely).
InteliVision 5 - New Features List 8
6 Changes in the version 1.8.0
IMPORTANT: If the upgrade from the version older than 1.7.0 is performed also see the notes of the
changes in the version 1.7.0
6.1 New features
Thesupport of the InteliSys GAS 1.2.0
if the controller has a large configuration the display unit IntelIVision 5 downloads only the actually
chosen language
ECU source address is displayed in the alarmlist item comming from ECU (in format ADR : number)
IMPORTANT: InteliSys GAS 1.2.0 archives and newer is compatible only with the GenConfig
version 3.8.0 and newer.
6.2 Bug fixes
Instrument SoftKeyMenuName did not respect the access rights correctly
History reading did not work correctly in any special cases
InteliVision 5 - New Features List 9
7 Changes in the version 1.7.0
7.1 IMPORTANT COMPATIBILITY NOTICE
(READ BEFORE THE UPGRADE)
IneliVision 5 1.7.0 firmware is fully compatible (with regards to Tier IV Final standard) with the
newest controller archives only :
InteliGen NT BaseBox 3.8.0 and
InteliSys NT BaseBox 3.8.0
InteliGen NTC BaseBox 3.8.0 and
InteliSys NTC BaseBox 3.8.0
The older controller firmwares will not work properly (with regards to Tier IV Final standard) with the
InteliVision 5 1.7.0
IMPORTANT: If the older archive is opened in GenConfig 3.6.0 and newer The aftertreatment meter
(instrument) in InteliVision 5 is not supported.
IMPORTANT: It is very recommended to upgrade both InteliVision 5 firmware to version 1.7.0 and
controllers archives to the newest ones (as specified above) to fully support of Tier IV Final
standard.
7.2 New features
Aftertreatment (Tier IV final) support
New aftertreatment icons added
New aftertreatment meter (instrument) added
Automatic aftertreatment screen when ECU module is added to the configuration
Support of the new versioning system
Support of the screen definition versioning system
to avoid incompatibility between display firmware and screen definition
Updated list of the connected modules to the controller
The ECU source address is displayed in the alarmlist page
InteliVision 5 - New Features List 10
8 Changes in the version 1.6.0
8.1 New features
Support of inteliSys Gas controller
Updated list of the connected modules
IMPORTANT: The display settings (Backlite time) is lost using the upgrade from 1.5.0 to 1.6.0
InteliVision 5 - New Features List 11
9 Changes in the version 1.5.0
9.1 Bug fixes
Forced Value can not be changed, because of incorrectly evaluated limits
InteliVision 5 - New Features List 12
10 Changes in the version 1.4.0
10.1 New features
Add support of a customer branch.
Just for customer branch purpose (for standard product update is not needed).
InteliVision 5 - New Features List 13
11 Changes in the version 1.3.0
11.1 New features
Add support of a customer branch.
Just for customer branch purpose (for standard product update is not needed).
InteliVision 5 - New Features List 14
12 Changes in the version 1.2
12.1 New features
Display of information relating to SW dongle
Support of new symbols for TIER 4 regulation (Available in Screen Editor from incoming GC)
Note: Firmware 1.2 comes with new interesting features. Below you can find their detailed description
12.2 Bug fixes
Binary indicators (Available in Screen Editor from incoming GC)
Invisible Setpoint values of ECON, INCON, DENOX
12.3 Display of information relating to SW dongle
Information relating to SW dongle (see SW dongle information on page 14) is now available in the controller
Info screen (Menu
Help&Other → ControllerInfo).
If no SW dongle is inserted or the controller does not support the communication object associated with SW
dongle, only 16 zeroes will be displayed.
Image 6.1 SW dongle information
12.4 Support of new symbols for TIER 4 regulation
Available in Screen Editor from incoming GC
The new symbols for the support of Tier 4 regulation were added to InteliVision 5. The types of added
symbols are displayed in the Types added TIER 4 symbols (page 15).All color variations of added TIER
4 symbols (page 15) displays all color variations. They are available to choose in
InteliVision 5 - New Features List 15
Screen Editor during your IV5 screen modification.
Emission fails
Exhaust fluid
Table 6.1 Types added TIER 4 symbols
Image 6.2 All color variations of added TIER 4 symbols
IMPORTANT: New TIER 4 symbols will be available in Screen Editor from incoming GenConfig
version.
12.5 Binary indicators
Available in screen editor from incoming GC.
There is fixed issue of invisible names of inputs/outputs of added peripheries DISTBIN and DISTBOUT when
using DigitBit, DigitBin and BinList instruments at the screens.
IMPORTANT: Binary indicators will be available in Screen Editor form incoming GC version.
12.6 Setpoints values of Econ, INCON, and DENOX
There is fixed issue with Setpoints values of ECON, INCON and DENOX. They are visible now and it is
possible to edit them.
InteliVision 5 - New Features List 16
13 Changes in the version 1.1.3
13.1 Bug fixes
Fixed problem with IV5 restart when Time object is used on a screen.
Fixed problem with IV5 restart after IV5 wakes up from a screen saver.
Fixed problem with intermittent communication drop-out when more IV5 displays is connected via NT
terminal connection.
Fixed problem with intermittent communication drop-out when using Direct connection to the controller.
InteliVision 5 - New Features List 17
14 Changes in the version 1.1.1
14.1 Support of direct communication between
InteliVision 5 and IG/IS-NT-(BB) controllers
It enables the usage of converters with constant communication speed in both directions between
InteliVision 5 and the controller.
With version 1.1.1 it is possible to run InteliVision 5 connected to controller RS232 or RS485 port with
following setting in the controller:
Option Controller port Setting in the controller
A RS232(1) RS232(1) mode = DIRECT
RS485(1)conv. = DISABLED
B RS485(1) Not possible
Port dedicated to NT-terminal line connection
C RS232(2)* ** RS232(2) mode = DIRECT
RS485(2)conv. = DISABLED
D RS485(2)* RS232(2) mode = DIRECT
RS485(2)conv. = ENABLED
* RS232 OR RS485 direct connection can be used. They cannot be used simultaneously.
** Only available in IG-NTC / IS-NT-BB
IMPORTANT: It is not possible to program InteliVision 5 through the direct communication
interface. Programming, font upgrade and download of the logo have to be done through NT-
terminal line (connection of InteliVision 5 to RS485(1) port dedicated to displays).
InteliVision 5 - New Features List 18
14.2 How to program InteliVision 5
For programming of new firmware, upgrade of fonts and logo download the InteliVision 5 has to be
connected to any IG/IS-NT-(BB) controller to it’s NT-terminal interface, i.e. RS485(1)/display port.
Then the programming is done from GenConfig tool:
1. Go to File → Firmware upgrade and Cloning → Display GC font change / FW upgrade
2. Select tab according to desired operation, e.g. Display firmware upgrade
3. Select firmware to be programmed (in this case InteliVision5-1.1.1)
4. Press Write to display button and wait until programming is complete
5. Disconnect InteliVision 5 from the controller NT-terminal interface.
InteliVision 5 - New Features List 19
14.3 How to connect InteliVision 5 to the controller
(DIRECT connection)
Option A
Option C
Analogical to Option A for second RS232 port
InteliVision 5 - New Features List 20
Option D
Note: Make sure that bias (pull up, pull down) resistors are connected only on one side of the RS485 line.
Other manuals for InteliVision 5
2
Table of contents
Other ComAp Monitor manuals
