Comax CM-DW01 User manual

Wireless Door/ Window Sensor
Introduction
Thank you
for choosing the COMAX’s Wireless
is fully compatible with Z-Wave
Every main powered Z-
Wave enabled device acts
transmission routes.
This sensor monitors door/window and send
Product Description and Specification
Specification:
Protocol: Z-
Wave
Frequency Range: 865.2 Mhz
Operating Range: Up to 50M
Operating Temp.:
Battery: CR123A
Installation
1. Unscrew and open the rear cover.
2.
Using the screws or adhesive tape fix the rear cover on the frame along the opening edge of door /
window.
3.
Insert a CR123A battery into the battery compartment and LED will start to flash slowly, which means the
sensor has not yet been “added”.
4. For addi
ng sensor to a network, Put the Z
add the CM-DW01
to your controller.
meter. Press the program switch of
please try again.
To remove the sensor from a network, Put the Z
instruction to delete the CM-DW01
from your controller. Press the program swit
6.
Fix the Magnet by using the adhesive tape or fixing screws, locate the Magnet close to the
distance between these two devices should be
Operation
1.
Opening the door/window to separate the
will flash once.
2.
Closing the door/window to align the magnet with the sensor will send the
flash once.
3.
Normal operation, the LED will not light.
Operation Manual
Wireless Door/ Window Sensor
CM-DW01
for choosing the COMAX’s Wireless
Door/Window sensor. This sensor is a Z-
Wave
Wave enabled device acts
as a signal repeater and multiple devices result in more possible
This sensor monitors door/window and send
Z-Wave
signal when door or window is opened and closed.
Product Description and Specification
Wave
Frequency Range: 865.2 Mhz
Operating Range: Up to 50M
line of sight
Operating Temp.:
-10°C to 50°C
Battery: CR123A
- 1Pc
Using the screws or adhesive tape fix the rear cover on the frame along the opening edge of door /
Insert a CR123A battery into the battery compartment and LED will start to flash slowly, which means the
ng sensor to a network, Put the Z
-Wave Interface Controller into “
add” mode, and follow
to your controller.
T
he distance between sensor and controller is suggested to be in one
meter. Press the program switch of
CM-DW01 for 1 second. The LED on the sensor
should go solid, if not,
To remove the sensor from a network, Put the Z
-Wave Interface Controller into “
delete” mode, and follow
from your controller. Press the program swit
ch of sensor
Fix the Magnet by using the adhesive tape or fixing screws, locate the Magnet close to the
CM
distance between these two devices should be
not more than 1.5cm.
Opening the door/window to separate the
magnet from the sensor will send t
he status of "ON"
Closing the door/window to align the magnet with the sensor will send the
status of "OFF"
Normal operation, the LED will not light.
Wave
enabled device and
as a signal repeater and multiple devices result in more possible
signal when door or window is opened and closed.
Using the screws or adhesive tape fix the rear cover on the frame along the opening edge of door /
Insert a CR123A battery into the battery compartment and LED will start to flash slowly, which means the
add” mode, and follow
instruction to
he distance between sensor and controller is suggested to be in one
should go solid, if not,
delete” mode, and follow
for 1 second
.
CM
-DW01 sensor the
he status of "ON"
and the LED
status of "OFF"
and the LED will

4. The CM-DW01 sensor equipped with tamper switch. If the cover of sensor is removed, the door sensor will
send an alarm report to the Z-Wave Interface Controller, and the LED will go solid.
Warranty terms
Comax Guarantees that every wireless Door/Window sensor is free from physical defects in material and
workmanship under normal use for one year from the date of purchase. If the product proves defective during this
one-year warranty period, Comax will replace it free of charge.
Note:This warranty does not apply to
•Damage to units caused by accident, dropping or abuse in handling, or any negligent use.
•Units which have been subject to unauthorized repair, taken apart, or otherwise modified
•Units not used in accordance with instruction
•Damages exceeding the cost of the product
•Transit damage, initial installation costs, removal cost, or reinstallation cost.