Comelit LogiFire 41CPE112 Owner's manual

EN
TECHNICAL AND
PROGRAMMING MANUAL
Addressable fire panel
art. 41CPE112 Passion.Technology.Design.
LogiFire
41CPE112

41CPE112 Addressable Fire Alarm Panel – Installation and Programming Manual
2
Table of Contents
1. INTRODUCTION .................................................................................................................................................... 4
1.1. General Description ................................................................................................................................. 4
1.2. General Specifications ............................................................................................................................. 4
1.2.1 General Technical Specifications ............................................................................................... 4
1.2.2 Possible Hardware Configurations ............................................................................................. 5
1.2.3 Environment .............................................................................................................................. 5
1.2.4 Electrical Characteristics ........................................................................................................... 5
2. INSTALLATION ...................................................................................................................................................... 7
2.1. Wall Mounting .......................................................................................................................................... 7
2.2. System Components ............................................................................................................................... 8
2.2.1 Front panel ................................................................................................................................ 8
2.2.2 Configuration of the basic modules .......................................................................................... 10
2.2.3 Description of the main PCB (control panel)............................................................................. 10
2.3. Connection of Signaling Devices ............................................................................................................ 12
2.3.1 Connecting of Sounders .......................................................................................................... 12
2.3.2 Connecting of Signaling Devices ............................................................................................. 12
2.3.3 Connecting to the Specialized Inputs ....................................................................................... 12
2.3.4 Loop Controller........................................................................................................................ 13
2.4. Connecting to the Main Power Source ................................................................................................... 14
2.5. Connecting the Accumulator Battery ...................................................................................................... 14
2.6. Connecting a Heat Printer ...................................................................................................................... 14
2.7. Connecting a Network Module ............................................................................................................... 15
3. PROGRAMMING TYPES...................................................................................................................................... 15
3.1. Programming via LogiProg Software ...................................................................................................... 15
3.2. Programming via Panel’s Keyboard ....................................................................................................... 16
3.3. Firmware Update ................................................................................................................................... 16
3.3.1 Firmware Update from Computer............................................................................................. 16
3.3.2 Firmware Update from USB Drive............................................................................................ 17
3.3.3 Copying Image File from the Panel to USB Drive ..................................................................... 17
4. FULL HARDWARE RESET .................................................................................................................................. 17
5. PROGRAMMING OF 41CPE112 FIRE ALARM PANEL ....................................................................................... 17
5.1. General Information for Programming and Operation ............................................................................. 17
5.2. Codes and Access Levels ...................................................................................................................... 18
6. DESCRIPTION OF THE OPERATION MODES .................................................................................................... 20
6.1. Review of Alarm Events ......................................................................................................................... 20
6.2. Review of Fault Events .......................................................................................................................... 20
6.3. Review of Disablements ........................................................................................................................ 21
6.4. Review of Running Tests ....................................................................................................................... 21
6.5. Review of Warning Messages ................................................................................................................ 22
6.6. Silencing the Internal Buzzer.................................................................................................................. 23
6.7. Silencing the Sounders .......................................................................................................................... 23
6.8. Activate Evacuation ............................................................................................................................... 23
6.9. Resetting the Panel ............................................................................................................................... 23
6.10. Indication Test ..................................................................................................................................... 23
7. DESCRIPTION OF THE PROGRAMMING MENUS .............................................................................................. 24
7.1. View History Log Menu .......................................................................................................................... 24
7.1.1 Review of Full Events List........................................................................................................ 24
7.1.2 Review of List of Events by Date ............................................................................................. 25
7.1.3 Deleting the Events in the LOG file .......................................................................................... 25
7.1.4 Printing Events ........................................................................................................................ 25
7.1.5 Printer Settings........................................................................................................................ 25
7.2. Zones Menu .......................................................................................................................................... 26
7.2.1 General Submenus ................................................................................................................. 26
7.2.2 Zones Testing ......................................................................................................................... 26
7.2.3 Disabling Zones ...................................................................................................................... 27
7.2.4 Programming Zone Parameters ............................................................................................... 27
7.2.5 Zone Name ............................................................................................................................. 27
7.2.6 Zone Operation Modes ............................................................................................................ 27
7.2.7 Programming Delays Т2 .......................................................................................................... 28
7.2.8 Arranging Zones in Groups ...................................................................................................... 29
7.3. Devices Setup Menus ............................................................................................................................ 29
7.3.1 Submenus for General Setting................................................................................................. 29

41CPE112 Addressable Fire Alarm Panel – Installation and Programming Manual
3
7.3.2 Saving the New Found Devices ............................................................................................... 30
7.3.3 Deleting Devices ..................................................................................................................... 30
7.3.4 Disabling Devices .................................................................................................................... 30
7.3.5 Fixing of Wrong Type Devices ................................................................................................. 31
7.3.6 Programming of Device Parameters ........................................................................................ 31
7.4. Addressing Menus ................................................................................................................................. 39
7.4.1 Set Address ............................................................................................................................ 40
7.4.2 Change Address ..................................................................................................................... 41
7.4.3 Self-Addressing, Autoaddressing (ID / IS) ................................................................................ 41
7.5. Panel Outputs Menus ............................................................................................................................ 42
7.5.1 Sounders Outputs ................................................................................................................... 42
7.5.2 Extinguishing Output ............................................................................................................... 42
7.5.3 Fire Output .............................................................................................................................. 43
7.5.4 Fault Output ............................................................................................................................ 43
7.5.5 Relay Outputs ......................................................................................................................... 43
7.6. General Settings Menu .......................................................................................................................... 44
7.6.1 Access Codes ......................................................................................................................... 44
7.6.2 Setting the Date and Time ....................................................................................................... 45
7.6.3 Setting Day/ Night Alarm Modes .............................................................................................. 46
7.6.4 Panel General Settings............................................................................................................ 46
7.6.5 Delay Т1 ................................................................................................................................. 47
7.6.6 Sounders Mode ....................................................................................................................... 47
7.6.7 Company Logo ........................................................................................................................ 48
7.7. Save Configuration Menu....................................................................................................................... 48
7.8. Restore Defaults Menu .......................................................................................................................... 48
7.9. Software Revision .................................................................................................................................. 49
7.10. Network ............................................................................................................................................... 49
7.10.1 Network Settings ................................................................................................................... 49
7.10.2 Panels Settings ..................................................................................................................... 49
7.11. Active Isolators Menu ........................................................................................................................... 50
7.12. Access Level 1 .................................................................................................................................... 50
APPENDIX А ............................................................................................................................................................ 50
APPENDIX B ............................................................................................................................................................ 52
APPENDIX C ............................................................................................................................................................ 53
APPENDIX D ............................................................................................................................................................ 54
APPENDIX E ............................................................................................................................................................ 55
DoP No: 044
Comelit Group S.p.A.
Via Don Arrigoni 5 - 24020 Rovetta S. Lorenzo BG Italy tel. [phone] - fax [phone] email:
[e-mail] - [e-mail]
EN 54-2:1997/A1:2006/AC:1999; EN 54-4:1997/A2:2006/AC:1999
41CPE112
Intended for use in fire detection and fire alarm systems in and around buildings.
Essential Characteristics
Performance
Performance under fire conditions
Pass
Response delay (response time to fire)
Pass
Operational reliability
Pass
Durability of operational reliability and response delay: temperature resistance
Pass
Durability of operational reliability: humidity resistance
Pass
Durability of operational reliability: vibration resistance
Pass
Durability of operational reliability: electrical resistance
Pass

41CPE112 Addressable Fire Alarm Panel – Installation and Programming Manual
4
1. INTRODUCTION
1.1. General Description
41CPE112 is an addressable fire panel with maximum coverage of 48 zones and up to 2 loops. The panel supports
communication protocol Comelit and operation with Comelit addressable device series.
Every Loop provides up to 250 devices (detectors and modules, regardless of the type).
An arbitrary number of devices can be added to each zone thus ensuring the easy adaptation of the system to any type
of configuration.
To avoid or significantly diminish problems when mounting the system it must be carefully planned prior to installation.
This includes: setting an address for every device and planning a name of maximum 40 digits (including the
spaces) for each address, thereby ensuring easy access to the device.
According to the acting standards for establishing fire systems and the plan of the building, the devices must
be grouped in zones.
1.2. General Specifications
The front panel consists of LCD module (4 rows x 40 symbols), functional buttons and system status LED indication.
Separate access level passwords provide access to the functions of the panel.
The fire alarm panel is designed on module structure as in the metal cabinet there are provided additional places for
mounting of a second loop controller for Loop 2 (Loop 1 is built-in the main PCB), a communication module and
redundant network module.
The panel has a built-in real time clock and calendar, allowing day and night time modes of work.
Switching over between the two modes can be automatic or manual. Events like FIRE, RESET, FAULT, etc., are saved
in the memory, thereby creating an event log-file. It contains the time and date, the address of the device, the name of
the device, the zone number, the name of the zone, etc.
1.2.1 General Technical Specifications
• Loops - 1 to 2:
o Loop 1 is built-in in the main board
o Loop 2 – optional, separately mounted to the main control panel
• Number of loop devices:
o Up to 250 devices (modules and/ or detectors regardless of the type) for every loop (max. 500 for the
entire system)
• 48 operation zones (Note: Zone numbers 17-48 do not cover the requirements of EN54-2/4. There is no LED
indication for the status of zones 17-48 on the front panel.)

41CPE112 Addressable Fire Alarm Panel – Installation and Programming Manual
5
• 9 groups for zones’ organization
• 5 monitored potential outputs:
o SND1 (Sounder 1)
o SND2 (Sounder 2)
o FIRE
o FAULT (The output is deactivated in case of fault event.)
o EXT (Extinguishing / Fire Protection – An output for sending an fire alarm signal to automatic fire
extinguishing system)
• 3 specialized inputs:
o In AmC* (Input Alarm Confirmation)
o In PC* (Input Protection Alarm Confirmation)
o In FP* (Input Fault Protection Panel)
* Covers the requirements on standard VdS 2540
• 4 non-monitored, programmable relay outputs with parameters: 15A@24VDC
• Display – letter and digits LCD module (4 rows х 40 symbols)
• Built-in real time clock, supported from integrated lithium battery - 3V, CR3032 type
• Memory log file for up to 10000 system events
• Comprehensive day/night mode facility
• 2 Steps of alarm levels (T1 and T2)
• Supports external thermo printer
• Multilanguage support for operation menus
• Easy software update via computer or USB drive
• Designed according the requirements of EN54-2/4
• Color: Grey RAL 7045
• Metal box cabinet for wall mounting: 330х430х150 mm
1.2.2 Possible Hardware Configurations
• Minimal Configuration
o Control panel (main PCB with one built-in loop controller)
o Indication (indication PCB with mounted LCD module)
o Power supply source
• Maximal Configuration
o Control panel (main PCB with one built-in loop controller)
o Indication (indicator PCB with mounted LCD module)
o Power supply source
o Loop controller (for the second loop)
o LAN module 41ECN000
o RS485 Redundant Network controller
1.2.3 Environment
• Degree of protection: IP30
• Operation temperature: -5ºС up to +40ºC
• Relative humidity: 95% (without condense)
• Storage temperature: -10ºС up to +60ºC
• Weight (without the battery): ~ 7 kg.
1.2.4 Electrical Characteristics
Earth Connection
The earth connection has to be realized in accordance with the rules for the electrical safety with the total resistance in
the circuit lower than 10Ω. It is mandatory to connect the main power supply cable to the middle input of the fire panel
terminal – see also item 2.4 Main power connection.
ATTENTION: Do not instal the fire panel near power electromagnetic fields (radio equipment,
electric motors, etc.)!

41CPE112 Addressable Fire Alarm Panel – Installation and Programming Manual
6
Main power supply
In normal operating conditions, the fire panel is powered from the mains voltage line. In case of mains voltage line loss
the fire panel is equipped with one rechargeable battery. The characteristics of the main power supply are as follows:
• Main power supply: 90 ÷ 264 VAC
• Frequency: 47 ÷ 440 Hz
• Electrical output: 4.2 А
Backup (accumulator) power supply
• Voltage output (U): 13,65V
• Accumulator battery: 1 x 12V / 18Ah, sealed lead-acid type rechargeable battery
• Internal resistance of the accumulator battery Ri: < 0.3Ω
• Max. dimensions of the accumulator battery: 167х181х76mm
• Type of the battery connection: with a cable lug, Ø5mm (M5) or cable shoe (according the type of the battery
terminals)
Loading capacity
• Max. loading capacity of one loop: 500 mA DC
• Max. loading capacity of AUX output: 500 mA DC
• Max. loading capacity of outputs SND1 and SND2: 500 mA DC
• Max. loading capacity of outputs FIRE, FAULT and EXT: 300 mA DC
• Max. total loading capacity (sum of the four mentioned above): 2.0 A DC
• Programmable relay outputs: 15A@24VDC
Consumption
• From the main power supply in standby mode:
o For a minimum configuration: 60 mA AC
o With mounted second loop controller: 65 mA AC
• From the backup power supply in FAULT mode and generated message ‘AC loss’:
o For a minimum configuration: 125 mA DC
o With mounted second loop controller: 213 mA DC
List of the used fuses
• Main power supply: 4А, Т type, glass time-delay fuse, size 5х20mm
• AUX output: 0,5А, PTC type, resettable fuse
• Outputs: 0.3А, PTC type, resettable fuse
• Accumulator: 7.0А, PTC type, resettable fuse
List of spare parts kit:
1
Resistor 10k ± 5%, 0.25W
6 pcs
2
Resistor 47k ± 5%, 0.25W
4 pcs
3
Resistor 20k ± 5%, 0.25W
3 pcs
4
Screw 4.2х38, cross slot DIN7981
4 pcs
5
Anchor 6х30mm
4 pcs
6
Fuse 4А, glass time-delay type 5x20mm
(for the power supply)
4 pcs
ATTENTION!
Qualified specialists only should install the panel.
The electronic components of the panel are vulnerable to electrostatic discharge.
Never add or turn off components which are being power supplied!

41CPE112 Addressable Fire Alarm Panel – Installation and Programming Manual
7
2. INSTALLATION
2.1. Wall Mounting
• The panel must be installed in a clean dry place and must not be subjected to impact or vibrations (Figure 1). It must
be situated far from heating appliances. The temperature must be within -5ºС and + 50ºC. The fire panel is not
waterproof!
• Unpack the panel and observe for visible damages due to bad transport or incorrect storing.
Figure 1
• Choose inlets for the main power supply cable, loops, sounders, control devices, etc. Remove the metal cap element
just from those holes for cable running (Figure 2).
Figure 2 – Elements of the metal bottom:
1 – Main mounting holes.
2 – Holes for cable running.
Dimensions: 330х430х150 mm

41CPE112 Addressable Fire Alarm Panel – Installation and Programming Manual
8
• Use the template in the set to fix the mounting holes of the metal box on the wall.
• Drill holes (suitable for anchors Ø6mm) on the wall and fix the metal box.
• Route the external cables onto the back box, make off connection glands etc., BUT DO NOT make any connections
at this stage. ENTER THE MAINS CABLE THROUGH ITS OWN CABLE ENTRY POINT AND KEEP MAINS WIRING
AWAY FROM SYSTEM AND OTHER LOW VOLTAGE WIRING.
• Connect the mains supply and earth to the power supply terminal (see Figure 16), BUT DO NOT apply the main
electrical supply at this stage.
• Place the battery in an upright position.
• Connect back the flat cable for the indication and the earthling point.
• Proceed with initial power up of the system and testing.
2.2. System Components
2.2.1 Front panel
Description of the front panel
elements:
1 – LED indication for the system
status. The descriptions are printed
on the paper label and can be
changed if needed, including for
language change.
2 – LED indication for the used zones
3 – Letters and digits LCD-module (4х40)
4 – Functional digits buttons
5 – Control and navigation buttons
Figure 5
1 – Description of system status LED indication:
LED
Indication/ Description
GENERAL FIRE (red)
Lights on permanently in case of fire alarm event – fire alarm signal from an
automatic or manual call point, or other auxiliary device connected to a panel
input.
GENERAL FAULT (yellow)
Lights on permanently in case of fault event in the system.
SYSTEM FAULT (yellow)
CPU FAULT. Lights on permanently in case of main microprocessor fault.
DELAY (yellow)
Lights on permanently in daytime mode and set time delay for one or several
outputs.
DISABLE (yellow)
Light on permanently in active disablement in the system.
TEST (yellow)
Light on permanently in system test mode.
SOUNDERS FAULT/ DISABLED
(yellow)
The LED will be active in case of fault or disablement of the sounders circuits.
The indication is as follows:
- Blinking in case of fault event in the sounder circuits.
- Lighting on when the sounder circuits are disabled.
FIRE CONFIRMED (yellow)
FIRE ALARM CONFIRMATION. Lights on permanently in activation of the
specialized “In AmC” input – see the description on page 12.
FIRE OUTPUT FAULT/
DISABLED (yellow)
The LED will be active in case of fault or disablement of the FIRE relay output.
The indication is as follows:
- Blinking in case of fault event.
- Lighting on when the output is disabled.

41CPE112 Addressable Fire Alarm Panel – Installation and Programming Manual
9
PROTECTION CONFIRMED
(yellow)
EXTINGUISHING STARTED CONFIRMATION. Lights on permanently in
activation of the specialized “In PC” input – see the description on page 12.
PROTECTION PANEL FAULT
(yellow)
EXTINGUISHING SYSTEM FAULT. Lights on permanently in activation of the
specialized “In FP” input – see the description on page 12.
POWER ON (green)
MAIN POWER SUPPLY ON. Lights on permanently in presence of 230V main
power supply.
SILENCE ALARM (yellow)
THE SOUNDERS ARE SILENCED. Lights on permanently when the sounders
are silenced (the LED is situated next to the button).
2 – Description of the zone LED indication:
LED
Indication/ Description
Zone indicators (red)
1 - 16
FIRE IN A ZONE. Lights on permanently in case of fire alarm in zones 1-16.
Blinking when zones 1-16 are in test mode.
Note: For zones from 17 to 48 there is no LED indication.
3 – Description of the LCD-module
The 41CPE112 fire alarm addressable panel is equipped with letter-digit LCD-module (4 rows x 40 symbols). The user
can enter device and zone names using the navigation and control buttons. The display has an adjustable backlight
with 20 levels of intensity.
4 – Description of the functional digit buttons:
Button
Description
Functional digit buttons
1 - 4
The buttons are active at access levels 2 and 3, and have the following
meaning:
- Introducing of access codes.
- Functional submenu entry.
- Changing of value or parameter status.
5 – Description of control and navigation buttons:
Button
Action
Description
Silence Buzzer
The button is active at access levels 1, 2 and 3. The button functionality is
deactivation of the internal buzzer.
Silence
Sounders
The button is active at access levels 2 and 3. The button functionality is
deactivation of the sounders in case of fire alarm event. After pressing the button
the LED next to it is lighting in yellow.
Reset
The button is active at access levels 2 and 3. The button functionality is resetting
the panel without switching off the main power supply.
Evacuation
The button is active at access levels 1*, 2 and 3. The button immediately
activates the sounders – the sounder delay is ignored if present.
* In case of fire alarm event in a zone and set sounder delay.
Buzzer and LED
general test
The button will activate all LEDs on the front panel – for events and zones, as
and the internal buzzer. The next pressing of the button deactivates the test.
ENTER
(Confirmation)
The button is active at access levels 1, 2 and 3. Use the button to confirm the
entered values and parameters; in the devices and zones menus use the button
to enter in a submenu for name and status changing.
CANCEL
(Rejection)
The button is active at access levels 1, 2 and 3. Use the button to reject the
entered values and parameters; one step back to the previous menu.
Navigation
buttons
The button is active at access levels 2 and 3. Use the arrows to scroll over the
menus; in the programming menus the buttons has a specific function for
changing values and switching between the editable fields.

41CPE112 Addressable Fire Alarm Panel – Installation and Programming Manual
10
2.2.2 Configuration of the basic modules
Figure 6 – Configuration of the modules in the box:
1 – Main PCB (control panel)
2 – Second loop controller (optional, it may not be present in your
system configuration)
3 – Power supply unit
4 – Terminal 230V for connection of the main power supply cable
5 – Place for mounting of a communication module Art. 41ECN000
6 – Place for mounting of redundant network module Art. 41ECB000
7 – Place for accumulator battery, 1 х 12V/ 18Ah
2.2.3 Description of the main PCB (control panel)
Figure 7 – Main PCB of the 41CPE112 fire alarm panel
Description of the terminal row (left to right):
• RELAY 1 - 4 – Programmable volt free change over relay contacts each, 24VDC@15A. Each relay has one
NO (normal open) and one NC (normal closed) contact with common lead on a terminal. When a relay output
is activated the NO contact is closed and the NC contact is opened.