QTAC 85 EMS-C User manual

Page | 1
85 EMS-C
Owner’s Manual
QTAC is a division of MTECH, Inc.
1072 Marauder, Suite 210
Chico, CA 95973
1.888.797.5100
www.qtacfire.com

Page | 2
Table of Contents
GETTING TO KNOW YOUR QTAC..................................................................................4
TRANSPORTING YOUR QTAC.......................................................................................7
Gross Vehicle Weight Rating.........................................................................................7
General QTAC Mounting and Fastening........................................................................8
Special Precautions for Carrying a QTAC on Ride-On ATVs or Side-By-Side UTVs ....9
OPERATING YOUR QTAC...............................................................................................9
Before Starting Up Your QTAC......................................................................................9
PUMP OPERATION........................................................................................................10
Priming the Pump after an Extended Period of Use ....................................................10
Tank Fill Requirements:...............................................................................................10
Tank Fill Through the Fill Tower ..................................................................................10
Pumping Using the Tank Water Supply.......................................................................11
Starting the Engine......................................................................................................11
DRAFT PROCEDURES..................................................................................................12
Drafting From an Auxiliary Water Source ....................................................................12
Connecting the Draft Hose ..........................................................................................12
Drafting to Fill the Water Tank.....................................................................................12
Pumping While Drafting From an Auxiliary Water Source ...........................................13
To Supply Water to the 1” NPSH Discharge................................................................14
STOPPING YOUR QTAC...............................................................................................14
Deploying the Folding Litter Carrier ................................................................................14
GETTING TO KNOW YOUR ATP FOAM KIT.................................................................15
OPERATING YOUR ATP FOAM KIT..............................................................................16
Before Using Your ATP Foam Kit................................................................................16
Using Your ATP Foam Kit............................................................................................16
Stopping Your ATP Foam Kit.......................................................................................17
STORING YOUR QTAC .................................................................................................17
General Storage ..........................................................................................................17
SPECIAL QTAC OPERATION........................................................................................17
Using More Than Water in Your QTAC .......................................................................17
SERVICING YOUR QTAC..............................................................................................18
Cleaning Your QTAC...................................................................................................18

Page | 3
Protecting Your QTAC.................................................................................................18
Routine QTAC Maintenance........................................................................................19
TROUBLESHOOTING YOUR QTAC..............................................................................19
The Pump Engine Will Not Start..................................................................................19
The Pump Will Not Build Water Pressure....................................................................19
Water Will Not Discharge From The Discharge Hose..................................................20
The Pump Engine Runs Erratically..............................................................................20
TECHNICAL SPECIFICATIONS.....................................................................................21
ADDITIONAL REFERENCES......................................................................................21
WARRANTY ...................................................................................................................22

Page | 4
GETTING TO KNOW YOUR QTAC
Figure 1 - Tank Components
1
Foam Cell (Optional)
5
Water Tank Site Gauge
2
Discharge Hose Reel
6
Water Tank Mounting Flange
3
Water Fill Tower
7
Water Tank Drain Port
4
Grab Handle
8
Folding Litter Platform
2
7
3
6
5
6
4
3
4
5
6
8
1
1
8
2
MEDIUM
PRESSURE
HIGH
PRESSURE

Page | 5
Figure 2 - Pump Components
All Valves Shown in the Open Position
1
Pressure Gauge (HP units only)
5
1” Pump to Reel Valve
2
Pump Primer Port
6
Tank to Pump Valve
3
1” NPSH Aux. Discharge Valve
7
Draft Hose Port
4
1” Pump to Tank Valve
8
Pump Drain Port
6
2
3
8
7
1
4
2
3
4
5
6
7
8
5
MEDIUM
PRESSURE
HIGH
PRESSURE

Page | 6
Figure 3 - Pump Engine Components
1
Fuel Fill
5
Oil Fill
2
Engine Throttle
6
Engine Switch
3
Carburetor Choke
7
Pull Starter
4
Fuel Shut-off Valve
2
3
4
1
1
5
6
7
1
2
3
4
5
6
7
MEDIUM
PRESSURE
HIGH
PRESSURE

Page | 7
Figure 4 –Detail of the litter carrier extension showing 1.) locking pin and 2.) extension
stop.
TRANSPORTING YOUR QTAC
Gross Vehicle Weight Rating
•Ensure that the gross vehicle weight rating (GVWR) of the QTAC carrying vehicle is
sufficient to support your QTAC unit with a full tank of water, plus any equipment,
fluids and personnel that you may wish to carry. Alternatively, you can reduce the
volume of water in your QTAC to maintain a GVWR under the limit of your vehicle.
1
2

Page | 8
General QTAC Mounting and Fastening
Figure 5 –Mounting Options
Ensure that your QTAC unit is secured to the carrying vehicle. Two main mounting
methods are available for your QTAC unit:
1. The preferred method of securing the QTAC to the bed of the vehicle is to mount
the QTAC at the flanges (Figure 5, Item3), located at the bottom of the water tank
on each side. The flanges have been machined to accept a variety of mounting
hardware options.
2. If using straps to secure the QTAC to the bed of the vehicle, feeding the strap
around two grab rail posts, is preferred. This distributes the downward force over
a greater area. (Figure 5, Item 4)
Securing the strap around a single grab rail post is acceptable. (Figure 5, Item 5)
Securing the strap around the upper grab handle is not an approved method to
secure the QTAC (Figure 5, Item1). This will result in warping of the plastic
handle, and will eventually lead to handle failure.
NOTE: It is important that QTAC EMS models are securely bolted to the UTV bed for
patient transport
1
2
3
5
4

Page | 9
For both mounting methods, ensure that the bottom of the QTAC (including the
mounting flanges) abuts a firm, flat surface or rack. Avoid significant leveraging of the
mounting flanges.
Special Precautions for Carrying a QTAC on Ride-On ATVs or Side-By-Side
UTVs
•Ensure that the area to which you are securing your QTAC is an approved
loading area for your ATV or UTV.
•Ensure that the weight of your QTAC does not exceed the maximum
recommended weight of the ATV or UTV loading area to which you are securing
your QTAC.
•Loading the bed of your ATV or UTV may affect steering response. Therefore,
the operator should spend some time operating the vehicle in a safe area (e.g.
wide and flat) once the QTAC has been properly secured and loaded to ensure
the vehicle operates in a safe manner. If the vehicle does not operate in a safe
manner, immediately recheck the GVWR calculations to ensure that the QTAC
unit is not overloading your vehicle. If the unsafe operation cannot be corrected,
do not carry your QTAC in this fashion.
•When carrying your QTAC unit on the rear rack of an ATV or in the bed of a UTV,
avoid steep side slopes. If an uphill must be traversed, it is recommend that you
back your ATV or UTV up the uphill to avoid the front wheels lifting on the uphill.
OPERATING YOUR QTAC
Before Starting Up Your QTAC
•Always wear appropriate eye, ear, and body protection when operating your
QTAC unit.
•Ensure that your QTAC has sufficient water in the water tank prior to operation.
The water level can be checked by viewing the water tank site gauge located on

Page | 10
the side of the water tank (Figure 1, Item 5) If the water tank is low on water,
open the water tank fill tower (Figure 1, Item 3)and fill the water tank with water.
•Check the pump engine fuel (Figure 3, Item 1) and oil levels (Figure 3, Item 5) as
needed, fill the pump engine with fuel and oil as specified in the engine manual
that came with your QTAC. For more information, see the Pump Operation
Manual and the Honda Owner’s Manual.
PUMP OPERATION
Priming the Pump after an Extended Period of Use
The QTAC pumps are a self-priming pump, meaning they do not need to be primed
before every use. However, if the pump is being started after not being in use for more
than 12 hours, it may be necessary to add water to the primer port (Figure 2, Item 2) to
ensure proper suction. To do so, simply pour water into the primer port until it is full,
secure the cap and start the engine.
Tank Fill Requirements:
MAX FILL PRESSURE: 100 PSI
MAX FILL RATE: 150 GPM
Tank Fill Through the Fill Tower
1. Open the fill tower and fill the tank. (Figure 1, Item 3)
(For filling the tank by way of draft suction, see page 12)

Page | 11
Pumping Using the Tank Water Supply
1. Ensure that all valves are in the proper position.
a. The tank to pump valve should be open to pull water from the tank.
(Figure 2, Item 6)
b. The 1” pump to tank should be cracked open slightly. (Figure ,2 Item 4)
c. The 1” NPSH Discharge should be fully closed. (Figure 2, Item 3)
2. Start the engine (see next page)
3. Water can now be discharged through the reel line.
(To operate the 1” NPSH discharge, see page 14)
CAUTION! During pumping operations, the operator MUST either a) leave the
pump to tank valve open slightly to bypass water through the pump (reference
Figure 2, Item 4), or b) leave the nozzle at least partially open at all times. Doing
so ensures that there is always water circulating through the pump to keep it
from overheating. Closing both the nozzle and the pump to tank line will result
in overheating the pump and pump failure.
Starting the Engine
1. Ensure that the engine has a sufficient amount of fuel in the gas tank. (Figure 3,
Item 1)
2. Ensure that the fuel shut-off valve is open. (Figure 3, Item 4)
3. Turn the Engine switch to the on position. (Figure 3, Item 6)
4. If the Honda engine is cold, apply the choke. (Figure 3, Item 3)
5. Pull the hand starter cord until the engine starts. (Figure 3, Item 7)

Page | 12
6. Apply throttle (Figure 3, Item 2) and decrease the choke until it is no longer
needed. The output of the pump is regulated by how much throttle is applied (as
well as the shut-off at the nozzle, and the pump to tank return).
DRAFT PROCEDURES
Drafting From an Auxiliary Water Source
Your QTAC has the ability to draft water from an auxiliary water source. The operator
can either draft in order to fill the tank, or draft straight into the pump and out a discharge
line, bypassing the tank.
Connecting the Draft Hose
Remove the Camlock cap covering the draft hose port. Secure the draft hose Camlock
coupling to the draft hose port. (Figure 2, Item 7)
Drafting to Fill the Water Tank
1. Close the tank to pump valve. (Figure 2, Item 6) Ensure that the pump head is
primed, as described on Page 10.
2. Place the brass foot valve connected to the end of the draft hose into the water
source. For faster priming submerge and fill the draft hose. Make sure not to
place the foot valve in mud or dirt, as it will suck debris into the pump. Always
elevate the valve off the bottom of the water source to reduce the chances of
debris intake.
3. Connect the draft hose to the draft port.
4. Open the 1” Pump to Tank valve. (Figure 2, Item 4)

Page | 13
5. Start the engine (see Page 11) and increase the throttle setting until you see
water entering the draft hose and being pulled into the pump head.
6. Monitor the water level using the water level sight tube. (Figure 1, Item 5)
7. Once the tank is full, decrease the throttle setting and shut off the engine. Return
the valves to the positions needed in order to pull water from the tank and
continue pumping operations. (see Page 11)
Pumping While Drafting From an Auxiliary Water Source
1. Close the tank to pump valve (Figure 2, Item 6) Ensure that the pump head is
primed, as described on Page 10.
2. Place the brass foot valve connected to the end of the draft hose into the water
source. For faster priming submerge and fill the draft hose. Make sure not to place
the foot valve in mud or dirt, as it will suck debris into the pump. Always elevate
the valve off the bottom of the water source to reduce the chances of debris
intake.
3. Open the hose reel nozzle slightly to ensure that water is allowed to run through
the pump after the engine is started.
4. Close the 1” Pump to Tank valve so that water does not enter the tank. (Figure 2,
Item 4)
5. Start the engine (see Page 11) and increase the throttle setting until you see
water entering the draft hose and being pulled into the pump head.
6. Use the hose reel discharge nozzle or 1” NPSH discharge line to carry out
suppression operations.

Page | 14
To Supply Water to the 1” NPSH Discharge
1. Connect your hose fitting to the 1” NPSH discharge outlet.
2. Lay out the hose, open the discharge valve slowly (Figure 2, Item 3) to charge the
line and supply water to the nozzle.
STOPPING YOUR QTAC
1. If opened, gradually close the shut-off valve at the end of the discharge hose
2. Decrease the throttle on the pump engine to the idle position (Figure 3, Item 2).
3. Set the engine switch to the “OFF” position (Figure 3, Item 6)
Deploying the Folding Litter Carrier
1. Lower the litter carrier extension so that the two extension stops rest
against the reinforcing plate on the water tank (Figure 4, Item 2)
2. As needed, adjust the extension stops so that the litter carrier extension is
level.
3. With the litter carrier extension in the down position, adjust the locking pin
so that it engages the drilled hole in the reinforcing plate.
4. Tighten the locking pin wing nut so that the litter carrier extension is
securely held in position.
5. Raising the litter carrier extension is a reversal of the steps above.

Page | 15
GETTING TO KNOW YOUR ATP FOAM KIT
Figure 6 –Typical ATP Foam Plumbing
1
Foam Cell Tank
4
Supply Hose Strainer
2
Vented Lid
5
Foam Proportioner
3
Foam Supply Valve
6
Proportioner Pressure Valve
1
2
3
5
6
4
1
2
3
6
4
5
MEDIUM
PRESSURE
HIGH
PRESSURE

Page | 16
OPERATING YOUR ATP FOAM KIT
Before Using Your ATP Foam Kit
Always wear appropriate eye, ear, and body protection when operating your
QTAC unit.
Using Your ATP Foam Kit
1. Install the15 GPM aerating nozzle on the discharge booster hose.
2. Ensure a proper amount of foam concentrate exists in the foam tank (Figure 6,
Item 1).
3. Start the engine per the QTAC Owner’s Manual.
4. Set the foam proportioner to the desired concentrate percentage
(Figure 6, Item 5).
5. Once the pumping system has developed pressure, open the hose line valve to
allow a slight flow.
6. Close the 1” Pump to Tank Valve to stop the introduction of foam concentrate into
the water tank. (Figure 2, Item 4) Remember that if this valve is closed, a
discharge must be open to prevent pump head overheating.
7. Open the Foam Supply valve (Figure 6, Item 3), and the Proportioner Pressure
Valve. (Figure 6, Item 6)
8. Open the discharge, apply foam as desired.
NOTE: It may take several seconds before foam becomes visible at the nozzle.
NOTE: If a foaming agent has recently been used in the QTAC, foam may
interfere with the pump’s ability to develop a prime. If you suspect this may be the
case, you may need to repeat the priming sequence several times before the
pump is clear of foam and the pump is able to develop suction.

Page | 17
Stopping Your ATP Foam Kit
1. Close the Foam Supply valve (Figure 6, Item 3), and the Proportioner Pressure
Valve (Figure 6, Item 6)
2. Flush the discharge system as necessary by running clean water until all traces of
foam have been removed.
STORING YOUR QTAC
General Storage
•Drain the fuel from the pump engine carburetor and fuel tank. See the Honda
Owner’s Manual for additional details.
•Drain any water from the water tank by opening all the valves, and the water tank
drain port (Figure 1, Item 7)
•Drain the water from the pump by opening the pump drain port (Figure 2, Item 8)
See the pump Instruction Manual for additional details.
NOTE: If your QTAC will be subjected to below freezing temperatures, ensure
that all water is drained from the water tank, pumping system, and hoses. Store
with all valves in the open position. If you would like to keep water in your QTAC
in below freezing temperatures, make sure to add an appropriate amount of RV
antifreeze to the water to prevent the formation of ice.
SPECIAL QTAC OPERATION
Using More Than Water in Your QTAC
If substances other than plain water have been used in the tank of your QTAC (e.g.
foam, pesticides, etc.), always clean and rinse the unit with clean water as soon as you
can after these chemicals have been used, until all traces of the chemicals have been
removed. Failure to flush the system in this manner can result in premature pump seal

Page | 18
failure, significant corrosion of the pump metal components, and build-up of chemical
byproducts in the tank and throughout the pumping system.
NOTE: Running substances other than plain water can cause significant foaming
to occur in the pumping system –if the pump has been run out of water with a
foaming agent in the tank, the pump will likely need to be primed on subsequent
water tank refills to remove the foam and to develop proper pressure.
Remove the cap from the pump primer port and fill the pump as needed (Figure
2, Item 2) with clean water. Ensure that all the foam has been forced from the
pump by continually pouring water into the primer port until all foam has been
displaced.
SERVICING YOUR QTAC
Cleaning Your QTAC
Your QTAC water tank is best cleaned with plain water. If additional cleaning power is
needed, a small amount of dish or car washing soap may be used. Avoid heavy
washing of the pump engine and surrounding area. Avoid the use of high pressure
spray on the water tank as the decals and rubber components may be damaged.
Protecting Your QTAC
Your QTAC is built of welded UV-stabilized copolymer polypropylene red plastic.
However, like any colored material, extended exposure to direct sunlight can eventually
fade the finish of the tank, hoses, hose reel and even the Honda engine. To keep this
from happening, cover the QTAC if it is stored outside and in direct sunlight. Also,
consider using a UV inhibitor on the plastic and rubber parts after washing the system,
such as 303 Aerospace UV Protectant.

Page | 19
Routine QTAC Maintenance
With the exception of the pump and pump engine, your QTAC requires no special
maintenance. For maintenance of the pump and pump engine, see the appropriate
manuals.
TROUBLESHOOTING YOUR QTAC
The Pump Engine Will Not Start
•Ensure that the engine switch is in the “ON” position.
•Ensure that the engine throttle is open slightly from the idle position.
•Adjust the choke. If the engine is cold, full choke will likely be needed.
•Ensure that fuel exists in the fuel tank, and the shut-off valve is on.
•For further troubleshooting information, see the Honda Owner’s Manual
The Pump Will Not Build Water Pressure
•Ensure that the pump engine is running and operating at a sufficient speed.
•Ensure that there is sufficient water in the water tank. There should be enough
water in the water tank so that the water level is visible in the water tank site
gauge (Figure 1, Item 5)
•Unless the draft hose kit is in use, ensure that the Tank to Pump valve is open
(Figure 2, Item 6), so that the pump is drawing water from the water tank and not
from the draft port.
•Ensure that the pump drain port plug is properly tightened and sealed (Figure 2,
Item 8).
•Ensure that the pump is properly primed with water. Remove the cap from the
pump prime port and fill the pump as needed (Figure 2, Item 2). If foaming
mixtures have been used in your QTAC recently, ensure that all the foam has
been forced from the pump by continually pouring water into the prime port until
all the foam has been displaced.

Page | 20
•Check the piping on the suction side of the pump to ensure that no air leaks are
present.
•For further troubleshooting information, see the pump Instruction Manual.
Water Will Not Discharge From The Discharge Hose
•Ensure that the pump engine is running and operating at a sufficient speed.
•Ensure that water pressure is available at the discharge hose port. This can be
checked by removing the hose connection at the discharge hose port.
•Check for hose kinking in the discharge hose.
•Ensure that the discharge hose shut-off valve is open.
•Ensure that the discharge hose nozzle is open.
The Pump Engine Runs Erratically
•Ensure that the engine has adequate fuel. Low fuel levels and operation over
rough and/or sloping terrain can cause the engine to momentarily run out of fuel.
•If the fuel has been stored for any length of time (and it has not been stabilized),
drain the fuel system and fill with fresh fuel.
•Proper engine performance is strongly dependent on a clean, lightly oiled air
filter. If the air filter is dirty or lacking oil, remove it from the air cleaner assembly,
clean with soapy warm water, rinse with fresh water and dry thoroughly. Once
dry, lightly saturate the element with clean engine oil and reassemble the air
cleaner assembly.