comfortel stella 2423 User manual

#2423 STELLA (XL WHITE BASIN)
#2424 STELLA (XL BLACK BASIN)
stella
washlounge
help.comfortel.com.au
owners manual

GENERAL SAFETY
1. Read carefully and keep these instructions in a
safe place.
2. Use this product only for its intended function and
do not use attachments not recommended by the
manufacturer.
3. Do not use outdoors.
PLUMBING
1. This unit must be plumbed by a licensed plumber.
IMPORTANT PLEASE READ THESE SAFETY INSTRUCTIONS
DO NOT ALLOW CHILDREN AROUND
THE WASHLOUNGE WHEN IN USE
ALL PLUMBING MUST BE COMPLETED
BY A LICENSED PLUMBER
IMPORTANT
IMPORTANT
GET STARTED
STELLA
Wash Lounge
SS
WITH XL BASIN
A A
B B
1230 48.4
580 22.8
315[12.4]
440[17.3]
480[18.9]
700 27.5

POSITIONING
DIAGRAM A
DIAGRAM B
PLUMBING ACCESS OPTIONS
Determine the best way to connect plumbing.
OPTION A: FROM WALL TO BASIN STAND
From behind the basin stand connect plumbing to the wall
OPTION B: FROM FLOOR BENEATH SEAT
From under the chair seat connect plumbing to the floor
ALL PLUMBING MUST BE COMPLETED
BY A LICENSED PLUMBER
IMPORTANT
If washing from behind, allow a minimum of 400mm of space behind your washlounge to provide room for access.
Wall
A
B
315[12.4]
440 [17.3]
480 [18.9]
1230 48.4
1310 51.5
80 3.1
580 22.8
100
50 100 100 50
400800
3200 (126”)
(31.5”) 800 (31.5”) 800 (31.5”) (15.75”)
700 (27.5”) 700 (27.5”) 700 (27.5”) 700 (27.5”)
(4”)(4”)(4”)(2”) (2”)
400 (15.75”)
If washing from side add 400mm (15.75"). All measurements in mm (inches).
BEFORE INSTALLING YOU SHOULD CONSIDER
THE FOLLOWING
• Allow for the necessary room around the unit for
free movement.
• If installing against a wall, a minimum distance of
80mm (3.15") between wall and bottom back of basin
is required to allow free movement of basin.
• If plumbing location is in wall (see Diagram A).
For neatness of finish it is preferable to bring water
and waste into the wash lounge in the same hole.
• If plumbing location is on floor (see Diagram A),
place wash lounge over.

GET STARTED
SECURE AND BOLT DOWN
FOOTPRINT
BEFORE INSTALLATION
THE WASHLOUNGE MUST BE SECURED TO THE FLOOR.
Making sure your wash lounge is supported from behind, remove the back
panel by unscrewing the two screws located on the left and right of the
access panel. Fix to the oor through connector brackets using bolts.

INSTALLATION & ASSEMBLY: BASIN & STAND
DIAGRAM D
1. Opening at back of chair
2. Steel frame
3. Bolts (supplied)
4. Stainless steel cover
5. Ceramic basin with Avitar Tilt.
BASIN ASSEMBLY
5
1
1
2
4
1
2
3
4
1
5
1
1
2
4
1
2
3
4
1
5
1
1
2
4
1
2
3
4
1
5
1
1
2
4
1
2
3
4
1
5
1
1
2
4
1
2
3
4
1
·Install Basin into steel frame and re-intall the
Washer & spring back into place and tighten.
Refer to Plumbing Diagram for Plumbing Connection
·Undo bolts and remove steel frame from the
opening of the back of chair.
·Flip steel frame over and re-bolt onto the inside
of the chair using bolts supplied.
·Secure the stainless cover onto the steel frame.
·Remove Washer & Springs from the basin

PLUMBING
1Flick Mixer
2Showerhead
3Showerhose basin collar
4Comfortneck
5O-ring
6Foam washers
7Plastic nut
8Flat seal
9Fitted flange
10 2 x Dyna bolts
11 Flexible waste pipe
12 Flange
13 Seal
14 P trap (not supplied)
15 Hot & cold braided hoses
16 Long nut
17 Plastic washers
18 Metal washers
19 O-ring
DIAGRAM C
PARTS
1
2
3
5
6
15
1817
19
16
8
9
11
12
13
14
10
7
4
STEP ONE
INSTALLING BASIN TO STAND
STEP TWO
WASHLOUNGE / STAND INSTALLATION
1. Washlounge MUST be secured to the floor. Secure to
the floor using 2 x Dyna bolts (supplied).
BASIN INSTALLATION
2. Remove washer & springs from the basin
3. Install basin into stand and re-intall the washer &
spring back into place and tighten.
TAP SET & HOSE INSTALLATION
4. Install Flick Mixer using O-ring, plastic and metal
washers & (Long Nut) and Shower Head using the
Showerhose Basin Collar, O-ring, Foam Washer &
Plastic Nut as indicated.
5. Place Flick Mixer and Shower Head Hoses through the
holes in the basin.
6. Connect Flexible Waste Pipe to Plug and Waste which
is already installed making use of the with Flat Seal and
fitted Flange.
PLUMBING CONNECTION
7. Connect Flexible Waste Pipe to P trap (not supplied)
making use of Seal and Flange.
8. Connect hot and cold (½” connection) braided hoses
to respective supplies.
9. Please attach Comfortneck to the basin.

CLEANING
UPHOLSTERY
· All upholstery needs some care; good housekeeping will help
to prolong the life of any upholstered products.
· Avoid extreme temperatures. Extreme cold can make your
vinyl prone to cracking, while extreme heat can cause
permanent stretching.
· Avoid exposing to direct sunlight for prolonged periods of time.
· Clean regularly (weekly) to remove body oils which cause
hardening or damage
· To clean use a sponge which has been moistened in warm
soapy water
· After cleaning with a sponge, dry with a soft, clean cloth
· Stubborn grime may require gentle scrubbing with a soft brush
Do not use:
·acetone ·furniture polishes
·bleach ·detergent
·abrasive cleaners ·steel wool
METAL AREAS
Wipe using regular cleaning products that are recommended
for stainless steel and metals.
Do not use:
·acetone ·furniture polishes
·bleach ·detergent
·abrasive cleaners ·steel wool
Damage caused by any improper treatment is not covered
by the product warranty.
A periodic inspection of all components and fasteners should be made to ensure that your washlounge is structurally
intact and functioning properly.
Damaged and broken parts should be replaced and loose fasteners tightened.
All maintenance to be carried out by a suitably qualified tradesperson.
MAINTENANCE
ALWAYS FOLLOW THE CLEANING INSTRUCTIONS
HOW TO CHANGE A SHOWERHEAD OR SHOWERHOSE
Please view our online how to videos and further troubleshooting:
https://help.comfortel.com.au/hairdressing-basins/

#2423 STELLA WASHLOUNGE WHITE BASIN
#2424 STELLA WASHLOUNGE BLACK BASIN
PRODUCT CODE The information contained in this document is subject to change without notice and
should not be construed as a commitment by Comfortel Furniture Pty Ltd.
Comfortel Furniture Pty Ltd. assumes no responsibility for any errors that may appear in
this document nor does it make expressed or implied warranty of any kind with regard
to this material, including, but not limited to, the implied warranties of merchantability
and fitness for a particular purpose.
Comfortel Furniture Pty Ltd. shall not be liable for incidental or consequential damages
in connection with or arising out of the use of this document and the program material.
PURCHASE DATE INVOICE NUMBER
NOTE YOUR PURCHASE DATE & INVOICE NUMBER FOR FUTURE REFERENCE
PLEASE RETAIN THIS INFORMATION FOR FUTURE REFERENCE
For more information about our products and services, contact us at comfortel.com.au
comfortel.com.au
©Comfortel Furniture. All rights are reserved. No part
of this document may be photocopied, reproduced or
translated to another language without written consent
of Comfortel Furniture Pty Ltd.
WARRANTY PERIOD
TERMS AND CONDITIONS. For more information about our warranty, please refer to our website.