COMHOMA H7137-KD User manual



󹋘

The backrest & seat cover you received has been vacuum-packed. Open the
plastic bag, take out the backrest / seat cover, let it breathe to the normal state.
󹆑 
󹆁
󹆃
󹆂
󹆏󹆉
󹆏 󹆉
󹆏󹆉
󹋙

󹆆
󹆇 󹆈
󹆊 󹆋 󹆌
󹆄 󹆅
Please check and ensure all the things are in the package. Please
contact us if something is not included. We will reply within 24 hours
and try our best to solve it.
󹆭
󹆎
󹆍󹆐
󹋚

󹆏
1.
2.
Carefully unpack and place parts
on a clean flat surface.
Insert the M6x125 screw into the
metal pipe 󹆈, thread the screw
out of the metal pipe 󹆈and align
it with the holes of the two sides
of the iron frame R 🅣, and install
the metal pipe 󹆈on the iron
frames R.
Please repeat this operation for
other 6 metal pipes 󹆈.
*NOTE：DO NOT tighten the screws
completely until all the screws are
fixed in the correct position.
󹆈
󹆊
󹆑
󹋛
assemble
the chair.

󹆉
󹆉
3. Refer to step 2 to install the
iron frames L.
4. Cover the iron frame decorative
sleeve L 󹆂 on the iron frame L.
*NOTE：DO NOT tighten the screws
completely until all the screws are
fixed in the correct position.
󹆂
󹆈
󹆊
󹆑
󹋜

󹆉
5. Fasten the Velcro of the Iron
Frame Decorative Sleeve L 󹆂.
6. Refer to step 4 and step 5 to
install the iron frame Decorative
Sleeve R 🅔.
󹆂
󹆏
󹋝

7. Cover the iron frame L with
the 󹆃Armrest Cover L.
*NOTE：After the 󹆃is installed
in place, zip up the 󹆃Armrest
Cover L as shown.
8. Cover the iron frame R with
the 󹆃Armrest Cover R.
*NOTE：After the 󹆃is installed
in place, zip up the 󹆃Armrest
Cover R as shown.
󹆉
󹋞
󹆏

9. Install the cup holders
into the armrests on
both sides.
10. Attach the metal frames 󹆆 to
the armrest L & R with screws
M6x20 󹆋.
*NOTE：Place the wide side of the
metal frames upward for installation.
If the position is incorrect, these parts
cannot be properly snapped into
the seat‘s metal frames.
󹆋
󹆏 󹆉
󹆏
󹆋
󹋟
󹆇

11.
12. Fold the seat cover 🅑 twice,
then align the hook, loop at
the bottom of the seat cover
󹅿 with the hook, loop at the
seat base 󹆁and join them
toghter with glue.
󹆁
❶
❷
󹋠
󹆐
After connecting the power
cords, plug 󹆍in the power
source. press the Recline &
Legrest button of the hand
control to expand the footrest
separetely.
󹆁
󹆍
󹆎
󹆐
󹆎
Hand Control
Recline
&
Footrest
RST
󹆍

13. Flip and extend the
seat cover 🅑to the
footrest of the seat
base 󹆁, and then
attach the Velcro in
sequence.
󹆁
❶
❶ Align the position before
pasting, make sure the pasted
position is aligned.
❷ Flip the hook, loop at the
middle of the seat cover and
paste it with the seat base.
❷
❸
❸ Fasten the hook and loop at
the end of the seat cover and
stick it on the bottom of
the footrest.
❹ Raise the seat base 󹆁and
paste Velcro on the bottom
of the seat base 󹆁and the
bottom of the seat cover 󹅿.
❹
❸
❹
󹆁

󹋡

15. frame
14. Press once the RST button to
restore the chair state. Align
and paste the Velcro on the
outside of the seat base 󹆁in
sequence.
16.
󹆁
󹋢
RST

17.
󹋣
Insert metal frames of parts v
（both）to the backrest.
Ensure they are put correctly.
18.

󹆄
󹋤
wires

19.
20.
󹋥

once
Press the RST once
4. Note：Press the Recline & Legrest or RST button once. Do not
hold it all the time to avoid damage to the recliner motor.
󹋦
Recline
&
Footrest
RST

1. Press the 󹉚 switch once to turn on the ambient light (blue)
under the footrest.
2. Press the 󹉚 switch once again to turn off the ambient light.
󹋧
Light Switch
Ambient Light

PULSE,PRESS,
WAVE,AUTO,NORMAL
󹋨
You can use (LUMBAR) massage part to enjoy.

󹋩

* Only move the recliner when it is in the ‘upright’ or ‘closed’
position. Never attempt to move the recliner when it is in any
of the open positions. Always use the arms to move the Reliner
– DO NOT use the backrest or backrest ear pieces.
󹋪
As all action products contain
moving parts, handle all items
with care.