Command access PM300ACD User manual

PM300AC/PM300ACD
# 20089_B
INSTALLATION INSTRUCTIONS
Visit our website for more details
www.CommandAccess.com
U.S. Customer Support
1-888-622-2377
Canada Customer Support
1-855-823-3002
A.
Includes
A. 12” Retrot Wiring Harness
B. AC Adaptor
C. PM300 Module
D. 6’ Power Lead.
E. 3/4”Velcro
F. Wire Connectors
Tools Required
• Wire Stripper
The PM300AC is a power booster interface module that ts inside of an electric latch pullback exit device.
It’s designed to work with 24VAC or unregulated 24VDC power supplies. When installed in the exit device,
it typically allows for a much longer wire run from the power supply to the exit device (typically up to 700’
with 18/2 wire) .
C.
D.
F.
**Please See Last Page for Technical Information**
E.
B.

24 VDC
Solenoid
ToThe power supply
PM300
Module
Module
Ceiling Tile
Module
LPM1 Series Installation
Example
Exit Device Installation
Example
Standard Placement
Module
Standard Placement
Hallow Metal Door
Option Only
Standard Placement
Optional Placement
PM300 Flow Diagram
Note: For LPM1 series option placement is only
recommended for Hallow metal doors. For wood
doors, use standard placement above ceiling tile
or in junction box.
recommended mode
AC A
dApTor

Adams Rite wire connections instructions:
Remove pushbar and separate push pad from device to gain access to the solenoid/circuit board assembly.
How to hook it up for other Manufactures Devices:
The unit comes with an easy plug-in 3 prong wire harness that to retrots to the existing solenoid. There is a second easy plug-in
2 prong wire harness that connects to the power from the power supply. The harness should be connected to the positive and
negative leads from the power supply. Generic examples and specic retrots are shown below.
Cut wires from Adams Rite Circuit board and remove board.
Tape back the two Blue wires.
A.
B.
Connect White and Red wires from solenoid to White wire from harness. Next, connect Black wire from
solenoid to Black wire from harness. Next, connect the AC Adapter to Harness and PM300.
Harness White (PM300-Yellow).
C.
Harness Black (PM300 Green).
Black
Red
White
Remove Circuit Board
Blue
recommended mode
PM300
ToThe power supply
AC A
dApTor
primAry
solenoid
primAry
solenoid
primAry
solenoid

Corbin/Russwin wire connections instructions:
Remove pushbar and separate push pad from device to gain access to the solenoid/circuit board assembly.
White #1
White
#2
Black #1
Harness White (PM300 Yellow)
Harness Black (PM300 Green)
Black #2
Precision pushpad and housing
Red #1
Black #1
Black #2
Black #2
Harness White (PM300 -Yellow)
Harness Black (PM300-Green)
Connect Red #1 solenoid wire to White harness wire. Next, connect Black #1to Black harness wire.
Disregard the two Secondary Black wires. Next, connect the AC Adapter to Harness and PM300.
Precision wire connections instructions:
Remove pushbar and separate push pad from device to gain access to the solenoid/circuit board assembly.
remove
B.
Connect primary White #1 wire to White harness wire. Next connect White #2 wire to Black harness wire.
Disregard both Black #2 wires. Next, connect PM300.
A.
Black #2
Red #1
Black #1
Black #2
Cut wires to disconnect solenoid from circuit board. Remove circuit board.
A.
recommended mode
Recommended mode
PM300
ToThe power supply
AC A
dApTor
PM300
ToThe power supply
AC A
dApTor
primAry
solenoid
secondAry
solenoid

PM300AC/PM300ACD
# 20089_B
Visit our website for more details
www.CommandAccess.com
U.S. Customer Support
1-888-622-2377
Canada Customer Support
1-855-823-3002
TECHNICAL INFORMATION
• Wires: Input to PM300AC non-polarized Black (+)(-)
• Operating Voltage Range: 20-26 VAC unltered 20-26 VDC Unregulated Voltage
• Output from PM300AC: Yellow=Pull Coil; Orange= Hold Coil; Green=Common
Power Supply Options for PM300AC and PM300ACD in Standard Mode:
The PM300AC works with the Adams Rite PS-LR, ACSI 1406, Corbin Russwin /Yale PS781N, Dorma PS-501,
Precision PS150-6, and AC transformer. Please check compatibility chart in link above for a list of other
manufactures power supplies.
Designed to work with 24 VAC & 24VDC unregulated power supplies. 12” retrot wiring
harness for other manufactures, such as, Adams Rite, Corbin/Yale, Precision, and more.
Models:
-PM300AC
Power Supply Options for PM300AC and PM300ACD in High Output Mode:
In High Output mode, the PM300AC has been tested with the Adams Rite PS-LR, ACSI 1406, Corbin Russwin
/Yale PS781N, Dorma PS-501, Precision PS150-6, and AC transformer.
PM300ACD - Sames as PM300AC above with the added feature of a .5 second delay.
Wire Run Guidelines:
For best results we recommend that your maximum wire run not exceed the following:
18ga.= 700’ 16ga. = 1000’
Specications:
• Fuse: Glass 3.5 - 5A, Resettable 1A trip
• Relay: 5A or greater
• Fuse: Resettable 2A trip
• Relay: 10A or greater
Standard Mode High Output Mode
Note: High Output is recommended for sluggish devices, vertical rods, & overcoming door misalignment.
PM300 Compatibility Chart
Scan me