Commercial Electric MB-50900 User manual

Fixed Wall Mount for Flat Panel TVs
MB-50900
200/300/400/600)
********

This mount has been tested to
support a television with diagonal
screen sizes between 37in. and 90in.
(94 cm & 2.29 m) and a weight
up to 100 lbs. (45.36kgs).
min3.9~max23.6''(min100~max600mm)
25.3''(643mm)
min3.9~max15.7''(min100~max400mm)
3.9''(100mm)
16.7''(425mm0
1.1''(27mm)
three 100 lbs.
(45.36kgs).
Before you begin, carefully read and understand the instructions
in this manual. Please follow the instructions in the order
presented in this manual and observe all warnings and cautions.
4-7
3/16 in. (4.5mm)

masonry
(sizes M6x30, M8x30, M8x50)
Lag bolt washer
10 20 30 40 50 60 70 80 90 100mm
1 2 3 4in
Mounting plate
Pre-Installation

Screw is too
long
Screw ts
correctly
Screw is too
short
DD EE
FF
injuries and property damage, make sure that
there are adequate threads to secure the
brackets to your TV. If you encounter resistance,
stop immediately and contact customer service.
Use the shortest screw and spacer combination
to accommodate your TV. Using hardware that is
too long may damage your TV. However, using
a screw that is too short may cause your TV to
fall from the mount.
To avoid potential personal
CAUTION:

masonry
3Attaching the mounting brackets
to the TV
Attach the mounting brackets ((B) to the back of the TV using the screws (DD), washers (EE)
and spacers(FF) you identified in step 1.
CAUTION:Tighten the screws so the brackets
are firmly attached. DO NOT OVERTIGHTEN. This
may damage your TV.
DD EE
FF
If you use a Samsung TV with deeper VESA holes, please use M8x50 screws and
Samsung spacers. ( These spacers are included with Samsung TV. )
Note:
Installation (continued)

Attach the mounting plate (A) using the lag bolts (CC) and lag bolt washers (BB) as shown.
6
Installing the mounting plate (concrete/masonry wall)
Insert anchors (AA) into the holes. Ensure the anchors are completely flush to the concrete surface even if covered
by a layer of joint compound or other material.
Use the mounting plate (A) as a template to mark the installation holes. Use a level to ensure the plate is level.
Use a
1
/
4
in. (6 mm) masonry drill bit to slowly drill 2.4 in. (60mm) pilot holes.Then use a 3/8 in. (10 mm) masonry
drill bit to expand pilot holes.
AA
BBCC
Installation (continued)
masonry blocks
masonry block.

HEAVY! You will need
assistance with this step.
Mounting the TV to the mounting plate
Holding the TV with the top of the screen tilted toward the wall, slide the upper notches of the mounting
brackets (B) over the upper lip of the mounting plate (A).
Tighten the two screws on the bottom of the mounting brackets (B) as shown to secure the TV.
Use a
3
/
16
in. (4.5 mm) wood drill bit to drill 2.2 in. (55 mm) pilot holes.
Use a commercially-available stud finder to locate the stud centers in the wall. Studs are usually spaced
16 in. apart.
Use the mounting plate (A) as a template to mark the installation holes. Use a level to ensure the plate is level.
Attach the mounting plate (A) using the lag bolts (CC) and lag bolt washers (BB) as shown.
7
6
Installing the mounting plate (wood stud)
BBCC
Installation (continued)