Commercial Electric MB-53290 User manual

(For up to 90" TVs,
Fits VESA 200/300/400/600)
MB-53290
Full Motion Wall Mount for Flat Panel TVs
********

This mount has been tested to
support a television with diagonal
screen sizes between 32in. and 90in.
(81.3 cm & 2.29 m) and a weight
up to 110lbs. (50kgs).
1/4in. (6 mm)
wood drill bit or
1/2in. (12 mm)
masonry drill bit.
four 110 lbs.
(50kgs).
Before you begin, carefully read and understand the instructions
in this manual. Please follow the instructions in the order
presented in this manual and observe all warnings and cautions.
4-10
62mm/2.44"615mm/24.21"

10 20 30 40 50 60 70 80 90 100mm
1 2 3 4in
A
D
E
F
B
C
Bubble level
Part Description Quantity
A Wall mount 1
B Mounting bracket 2
CThumb screw 2
DAllen key 1
1
E
F
Wrench 1
Part Description Quantity
AA 4
BB 4
CC 4
DD 4 each
8 each
EE
FF
4
Nylon anchor
Lag bolt washer
Lag bolt
Screw (size M5x14,M6x14,M6x30,M8x30,M8x50)
Washer
Spacer (size Φ15xΦ8x5 and Φ15xΦ8x15)
Pre-Installation
masonry

masonry
1
Ensure the wall you select is a weight-bearing wall.
Failure to observe this precaution can result in serious physical
injury and/or property damage. Consult a professional installer or
contact customer service if you have any questions.
CAUTION:

Installing the wall mount (concrete/masonry wall)
2
Use the wall mount (A) as a template to mark the installation holes. Use the bubble level (F) to ensure the wall
mount (A) is level.
AA BB CC
Use a
1
/
2
in. (12 mm) masonry drill bit to slowly drill 3.7 in. (95 mm) pilot holes.
Insert anchors (AA) into the holes. Ensure the anchors are completely flush to the concrete surface
even if covered by a layer of joint compound or other material.
Attach the wall mount (A) to the wall using the lag bolts (CC) and lag bolt washers (BB) as shown.
F
Installation (continued)
masonry blocks
masonry block.

3
Use a commercially-available stud finder to locate the stud centers in the wall. Studs are usually spaced 16 in. apart.
Use the wall mount (A) as a template to mark the installation holes. Use the bubble level (F) to ensure the wall mount
(A) is level.
Attach the wall mount (A) to the wall using the lag bolts (CC) and lag bolt washers (BB) as shown.
Use a
1
/
4
in. (6 mm) drill bit to slowey drill 3.5 in. (90 mm) pilot holes.
Installing the wall mount (wood stud)
F
BB CC
Installation (continued)

Screw is too
long
Screw ts
correctly
Screw is too
short
DD EE
FF
4 5
injuries and property damage, make sure that
there are adequate threads to secure the
brackets to your TV. If you encounter resistance,
stop immediately and contact customer service.
Use the shortest screw and spacer combination
to accommodate your TV. Using hardware that is
too long may damage your TV. However, using
a screw that is too short may cause your TV to
fall from the mount.
To avoid potential personal
CAUTION:
Installation (continued)

8
DD EE FF
mounting brackets to the TV
6
Using the washers (EE) and screws (DD, size M5x14,M6x14) to attach the TV of flat back.
Or using the spacers (FF), washers (EE) and screws (DD, size M6x30, M8x30, M8x50) to
attach the TV of curved or recessed back.
CAUTION:Tighten the screws so the brackets
are firmly attached. DO NOT OVERTIGHTEN. This
may damage your TV.
DD EE
Installation (continued)

9
7
Hang the TV on the wall mount and tighten the thumb screws (C) as shown to secure the TV.
Attaching the TV
HEAVY! You will need
assistance with this step.
Installation (continued)

10
F
E
E
D
±90º
±90º
±90º
+5º
-15º
+3º -3º
Managing the cable
Route cable along the arm.
8
Adjusting the TV to the desired position
Leveling: Using the wrench (E) to release or tighten the screws on the VESA plate as shown. Assist
yourself with the bubble level (F).
Tilt: Using the Allen key (D) to release or tighten the knob on the VESA plate as shown.
9
Installation (continued)