Comnet FVT110M1/BO User manual

INS_FVT110/BO_REV–
2/15/12
PAGE 1
INSTALLATION AND OPERATION MANUAL
FVT110(M,S)1/BO
IN-DOME 10-BIT DIGITAL VIDEO TRANSMITTER WITH
BOSCH BIPHASE AND BILINX CAMERA CONTROL
The FVT110/BO is a video transmitter and data transceiver that supports the
simultaneous transmission of short haul quality 10-bit EIA RS250C digital video and
Bosch Biphase and Bilinx camera control signals over one single mode or multimode
optical fiber.
The FVT110/BO in-dome module supports Bosch Bilinx up-the-coax camera control
over its entire specified fiber distance. The series features a unique time-base
correction algorithm that removes the usual distance limitations associated with
up-the-coax control.
Bi-color (Red/Green) LED indicators are provided for rapidly ascertaining equipment
operating status. Figure 2on Page 3describes the LED indicators for each light on the
receiver unit.
The FVT110/BO is intended for mounting within the Bosch dome. See Page 2for
mounting instructions.

INS_FVT110/BO_REV–
2/15/12
PAGE 2
CONNECTIONS FOR BOSCH CAMERA FIBER MODULE:
IN-DOME VIDEO TRANSMITTER MODULE (FVT110 / PCA1144):
* NOTE: Data LED D2 will flash green when Bosch Biphase data is received.
SINGLE MODE
OR MULTIMODE
OPTICAL FIBER
FIGURE 1 – FVT110/BO TRANSMITTER
INSTALLATION AND OPERATION MANUAL FVT110(M,S)1/BO
TECH SUPPORT: 1.888.678.9427
1. Install provided accessory
mounting kit as shown.
Secure the insert into
camera with screws.
2Connect power and data
from the camera to the
module at J5 (8-pin male
connector with white
plastic shroud) with
Bosch’s 5-pin to 8-pin
cable assembly.
Video LED D1 should
illuminate red.
Data LED D2 should stay
off*.
Link LED D3 should
illuminate red.
3. Connect video to
module at J4 (2-pin
male connector with
white plastic backing)
with ComNet’s 2-pin to
BNC cable, connecting
the other end to the
Dome BNC.
Video LED D1 should
illuminate green.
4. Connect Single mode or
Multimode fiber to U11
(single STfiber optic
connector).
Link LED should
illuminate green once
receiver is powered on
and link is established
over the fiber.
5. Attach the
FVT110/BO module to
the accessory insert with
white plastic stand-offs.
The stand-offs will snap
into the gold mounting
holes in the module as
shown.

INS_FVT110/BO_REV–
2/15/12
PAGE 3
INSTALLATION AND OPERATION MANUAL FVT110(M,S)1/BO
CONNECTIONS FOR BOSCH CAMERA FIBER MODULE (continued):
EXTERNAL VIDEO RECEIVER MODULE (FVR110):
1. Connect power to module:
Use +9 VDC adapter included with module, or insert into ComNet rack.
POWER LED should illuminate green.
LINK LED should illuminate red.
VIDEO LED should illuminate red.
DATA LED should stay off.
2. Connect video output to monitor:
Attach to BNC connector labeled VIDEO OUT
3. Connect fiber to module:
Attach Single mode or Multimode fiber to ST fiber optic connector labeled OPTICAL.
4. If Biphase data is used to control the camera then connect data to screw terminal block on module:
Biphase CODE+ should be connected to DIN+.
Biphase CODE- should be connected to DIN-.
Shield should be connected to GND.
NOTE: LINK LED will illuminate green once a link is established over optical fiber with the In-Dome Transmitter module.
VIDEO LED will illuminate green when active signal is detected at the BNC.
DATA LED will flash green when Biphase commands are detected at the data connector.
FIGURE 2 – LED INDICATORS (FVR110 RECEIVER)
LINK VIDEO DATA IN POWER
GREEN Communication link
has been established
over optical fiber
An active video signal
is present on the BNC
connector.
An active data signal is
present on the pins of
the data connector.
Unit powered up
RED Communication
link has not been
established.
– – –
OFF Unit powered down.

INS_FVT110/BO_REV–
2/15/12
PAGE 4
INSTALLATION AND OPERATION MANUAL FVT110(M,S)1/BO
FIGURE 3 – BIPHASE DATA SWITCH POSITIONS (FVR110)
The mode for each data channel is configured using a pair of switches on the front panel of the receiver unit. The 2 position CC Contact Switch is not used
when connected to an FVT110/BO in-dome module.
FIGURE 4 – DATA CONNECTIONS
Switch
1 2 GND
DIN (–)
DIN (+)
DOUT (–)
DOUT (+)
Bi-phase
DOUT(+)
DOUT(–)
DIN(+)
DIN(–)
Data In (+)
Data In (–)
Data Out (+)
Data Out (–)
Customer
Equipment
Customer
Equipment
UTC Control
FVT110/BO
FVT110/BO
Customer
Equipment
Customer
Equipment
FVR110
FVR110
Up-the-Coax
Control Receiver VIDEO IN VIDEO OUT Up-the-Coax
Control Transmitter
© 2012 Communications Networks Corporation. All Rights Reserved. “ComNet” and the “ComNet Logo” are registered trademarks of Communication Networks, LLC.
3 CORPORATE DRIVE | DANBURY, CT 06810 | USA
T: 203.796.5300 | F: 203.796.5303 | TECH SUPPORT: 1.888.678.9427 | [e-mail]
8 TURNBERRY PARK ROAD | GILDERSOME | MORLEY | LEEDS, UK LS27 7LE
T: [phone] | F: [phone] | [e-mail]
INSTALLATION CONSIDERATIONS
This fiber-optic link is supplied as an in-dome module. Units should be installed in dry locations protected from extremes of temperature and humidity.
CAUTION: Take care not to press on any of the LEDs.
IMPORTANT SAFEGUARDS:
A) Elevated Operating Ambient - Consideration should be given to installing the equipment in an environment compatible with the maximum ambient temperature
(Tma) specified by the manufacturer.
B) Reduced Air Flow - Installation of the equipment should be such that the amount of air flow required for safe operation
of the equipment is not compromised.