compulocks BrandMe 140B User manual

Assembly Instructions
©Compulocks Brands Inc. All Rights Reserved.j
www.compulocks.com | [e-mail] | [phone] Sheet 1 of 4
If you plan on a constant power connection
to your Tablet, you will need to obtain a
longer USB cable, allowing you to route the
cable through the Upright
Extrusion.
You will also need a AC Power Cord to
connect to a Power Cube, These Cables are
not supplied with the Stand.
BrandMe SKU: 140B/W
Hardware Kit
Item Description
B
C
G
H
I
J
L
B
H
I
G
C
J
Before Getting Started
Exploded View
Item Description Qty
A
B
C
D
E
F
G
H
K
L T-25 Screwdriver
AB
B
C
D
DK
H
H
E
G
G
F
H
H
H
H
Top End Assembly
M5 x 20mm Button Head Torx
T-25 Torx L-Wrench
Upright Extrusion
Base Cover
Base
M5 x 40mm Round Spacer
M5 x 20mm Flat Head Torx
Graphic Panel
1
4
1
2
1
1
2
8
1
1
M5 x 20mm Button Head Torx
T-25 Torx L-Wrench
M5 x 40mm Round Spacer
M5 x 20mm Flat Head Torx
M4 x 8mm Button Head Phillips
M5 Hex Wrench
T-25 Screwdriver
4
1
2
8
4
1
1
Qty
L

45
Assembly Instructions
©Compulocks Brands Inc. All Rights Reserved.j
www.compulocks.com | [e-mail] | [phone] Sheet 2 of 4
BrandMe SKU: 140B/W
Wiring Notch
Locate the Upright Extrusions (D). Make
sure extrusion has the flat edge facing
forward. Install the M5 X20mm Flat Head
Torx Screws (H) tighten using T-25 TorxWrench (C).
Note:
Make sure
screws in
Upright Extrusion
are Tight
CH
D
Front
Front
Back
Or
Or
Or
Prior to installing Upright Extrusion route USB
Extended USB cable into extrusion. Leave
9-10” of cable at the top of the extrusion.
Prior to installing Upright Extrusion route USB
Extended USB cable into extrusion. Leave
9-10” of cable at the top of the extrusion.
Bottom of Extrusion
Top of Extrusion
9”-10” of Cable
Extended USB Cable
Not Included.
Install
the
Uprignt Extrusion (D) using
M5X20mm Flat Head Torx Screws (H)
tighten using T-25 Torx Wrench (C).
Bottom of
Extrusion
Note:
Make sure
screws in
Upright Extrusion
are Tight.
D
C
L
H
Front
Front
Back of Base
Tip:
To prevent A/C
cord from
disconnecting, tie
a knot in the cord.
Power Cable Not
Included.
Route USB cable and plug into charging
cube. Four 3/8” holes provided in the base
for Floor Mounting
3
F
Install the two Round Spacers (G) using two
of the M5 x 20mm Flat Head Screws (H)
tighten using T-25 Torx Wrench.
CL
L
H
G
G
H
Front
Back
21
Route USB cable through Base Cover (E)
as shown.
Route Sync
Cable End
6

10
Assembly Instructions
©Compulocks Brands Inc. All Rights Reserved.j
www.compulocks.com | [e-mail] | [phone] Sheet 3 of 4
11
BrandMe SKU: 140B/W
Secure Base Cover with M5 X 20mm Flat
Head Torx Screw (H) using T-25 Torx Wrench
(C). Install Graphics panel (K) as shown.
Install Top End Assembly (A) using
M5 X 20mm Button Head Torx Screws (B),
securing with T-25 Torx Wrench (C).
Tablet Enclosure mounts to 100mm mounting
pattern. Use M4 x 8mm Button Head Phillips
(I) to attach Enclosure.
I
I
I
I
Tablet Enclosure
for Reference
Adjust Tilt Tension by accessing the three screws
on the back of the Top End Assembly. Use M5
Hex Wrench (J) to adjust screws.
Back View
7 8 9
Or
Or

Assembly Instructions
BrandMe SKU: 140B/W
©Compulocks Brands Inc. All Rights Reserved.j
www.compulocks.com | [e-mail] | [phone] Sheet 4 of 4
Graphic Panel Specifications
Maximum Material Thickness of
.250”/ 6.35mm
Option of using two pieces of
.125” /3.18mm thick material
back to back.
Shaded area represents Visiable
Graphic Area when panel is inserted
into Extrusion on Stand.
.375” or 9.53mm will be covered
by the Extrusion on both sides of
the Graphic Panel.
NOTE: The Graphic Slides into
the grooves of the Vertical
Extrusions of the Stand.
5.25”
13.33cm
6.0”
15.24cm
34.75”
88.26cm