Comsoft DF PROFI II CPCI User manual

DF PROFI II CPCI
Installation Instruction
V1.0
13.08.2002
Project No.: 4019
Doc-ID.: DF PROFI II CPCI-
COMSOFT

d:\windoc\icp\doku\hw\dfprofi ii cpci\df profi cpci_e ii.doc
Revision History
Version Date Description
V1.0 13.08.2002 Initial Version
Approval
Version Quality Manager / Date Project Manager / Date
V1.0
(L. Merz) (__________)
Version Customer Representative / Date
V1.0
COMSOFT GmbH
Wachhausstraße 5a
D-76227 Karlsruhe
Phone [phone] - 0
Fax [phone] - 129
Copyright 2004 by COMSOFT GmbH
This document is protected by copyright. Reproduction, duplication, publishing, transfer or disclosure of the contents of this
document are only permitted after prior written agreement has been obtained from COMSOFT GmbH.

DF PROFI II CPCI - Installation Instruction Contents
Contents
1 Installation of the Board.................................................................................................... 1
2 Pin Assignment ................................................................................................................. 2
3 Technical Data .................................................................................................................. 3
4 CE- Conformity Declaration............................................................................................. 4
COMSOFT V1.0 / 13.08.2002 i

Contents DF PROFI II CPCI - Installation Instruction
List of Figures
Figure 1: DF PROFI II CPCI - Board.........................................................................................1
Figure 2: Profibus-Terminator ....................................................................................................2
List of Tables
Table 1: Pin Assignment.............................................................................................................2
Table 2: Technical Data ..............................................................................................................3
ii V1.0 / 13.08.2002 COMSOFT

DF PROFI II CPCI - Installation Instruction Installation of the Board
1 Installation of the Board
The DF PROFI II PCI is a plug&play-compatible board. The configuration entirely takes
place by means of the delivered software or the BIOS of your PC respectively. Thus, no
jumpers or DIP-switch adjustments are necessary.
To mount the board, please proceed as follows:
please see also the operating instructions of your PC.
• Select a free CPCI slot.
• Plug the DF board into the determined slot. Pay attention
to a proper adjustment of the board in the guidance (avoid canting !).
• Screw down the board.
Remark: When mounting, please follow the safety instructions for
electronic modules against electrostatic charge.
Figure 1: DF PROFI II CPCI - Board
COMSOFT V1.0 / 13.08.2002 1

Pin Assignment DF PROFI II CPCI - Installation Instruction
2 Pin Assignment
Pin Number Signal Function Direction
1 - shielding
3 RxD/TxD-P Data+ Input/Output
5 0V (potential free 80 mA) Feeding of bus terminator Input
6 5V (potential free 80 mA) Feeding of bus terminator Output
8 RxD/TxD-N Data- Input/Output
Table 1: Pin Assignment
Remark: To assure correct operation of the PROFIBUS, a terminating resistor must be
mounted at each bus end (Purchase No.: 4000-7-002-H).
390 Ω220 Ω390 Ω
Cable type A
Data+
+5V Data- 0V
390 Ω150 Ω390 Ω
Cable type B
Figure 2: Profibus-Terminator
2 V1.0 / 13.08.2002 COMSOFT

DF PROFI II CPCI - Installation Instruction Technical Data
3 Technical Data
Processor Net+Arm 40
Profibus controller ASPC2
Supported protocols DPV0 Master Class 1
DPV1 Master Class 2
Clock pulse 33 / 48 MHz
Memory 1 Mbyte SRAM, 2 Mbyte Flash
Memory
Interfaces 1
Interface physics RS485 (isolated)
Data rates 9600 Bit/s – 1200 Kbit/s
PROFIBUS Isolation Voltage 500 VDC
Power consumption +5V / 1100 mA
Dimensions 175 mm * 107 mm
Table 2: Technical Data
COMSOFT V1.0 / 13.08.2002 3

CE- Conformity Declaration DF PROFI II CPCI - Installation Instruction
4 CE- Conformity Declaration
We herewith declare that the PC-interface
DF PROFI II CPCI
corresponds to the requirements stated in the
EU standards 89/336/EWG and 92/31/EWG.
The interface corresponds to the following standards:
EN 50082-1, EN 50082- 2 and EN 50081-1
Manufacturer:
COMSOFT GmbH
Wachhausstr. 5a
D-76227 Karlsruhe
4 V1.0 / 13.08.2002 COMSOFT