Conbrov T-11 User manual

Model No.: T11
T11 Starlight Mini-PIR Camera
User Manual

Table of Contents
Part 1 Before First Use..............................1-2
Part 2 Quick Guide.......................................3
Part 3 Detailed User Manual.....................4-21
Part 3 Detailed User Manual
Safety precautions....................................... .4
Warning on invasion of privacy....................... 5
What’s Included............................................ 6
T11 Diagram................................................ .7
Before Using Your Conbrov T11 Camera.... .8-11
How to Use Your Conbrov T11 Camera......12-14
1.Turning the Camera On/Off.....................12
2.How to Record a Video ......................12-13
3.How to Switch Into Night Vision ..............14
4.How to Play the Video ...........................14
LED status..................................................15
Technical specifications...............................16
FAQs.....................................................17-18
Warranty.....................................................19
Disposal......................................................19
Declaration of conformity..............................19

Part1 Before First Use
Charging the camera
Before the first use, charge the camera for about
three to four hours via your PC or USB charger
(we recommend using the "5V/1A" power
adapter)
Formatting the microSD card
Before the first use, format the microSD card to
FAT32 format (applicable to Windows system
ONLY). The camera only supports class 10
microSD cards with at least an 8GB capacity. It
supports cards up to 32 GB.
Yellow indicator
1
Yellow indicator

Part1: Before First Use
Resetting the camera
If the camera malfunctions for any reason, reset
it with the included pin. A small paperclip can
also be used.
2

Part 2 Quick Guide
A.Install the microSD Card B.Turn On/Off
C.Record A Video D.Play The Video
OFF flashes
alternating red
and blue and then
turns off
Record a Video
flash 3 times blue
1
2
US B2.0
For more detailed information, see Part 3: Detailed
User Manual.
ON lights up blue
and the camera is
in standby mode
2S power on
3
2S
2S

4
Safety precautions
Read this instruction manual carefully before using the
camera. It contains important information for your safety
as well as operating and maintenance instructions.
Follow all safety precautions in order to prevent damage
due to improper use of the camera.
Keep this user manual carefully for future use. Should
this camera be passed along to a third party, this user
manual must be handed on as well.
Use the camera only for its intended purpose.
In the event of improper use or erroneous handling, no
liability can be assumed for any possible damage which
may occur.
Never try to repair the camera yourself. Only allow
qualified personnel to repair the camera in the event of
malfunctions.
Warning! The camera is not waterproof.Never immerse
the camera in water or other liquids while cleaning or
operating it.
Do not open the housing under any circumstances. Do
not introduce any metal objects into the interior of the
housing.
Never use accessories which are not recommended by
the manufacturer.
Keep the camera away from all hot surfaces and naked
flames. Protect the camera from extreme heat and cold,
dust, direct sunlight, humidity and drops or jets of water.
Do not place any heavy objects on the camera.
The manufacturer is not responsible for any missing
video data due to maloperation, microSD card
malfunctions, camera angle limitation, etc.

5
Warning on invasion of privacy
The camera should be used for legal purpose only.
Follow the laws of your country.
Recording and circulating an image of an individual
may constitute an infringement of their privacy for
which you could be liable. Ask for authorization
before filming individuals, particularly if you want to
keep your recordings and/or circulate images on
the Internet or any other medium. Do not circulate
a degrading image or one which could undermine
the reputation or dignity of an individual.

Model No.: T11
T11 Starlight Mini-PIR Camera
User Manual
What's included
USB cable Camera Manual
Pin
6

T11 Diagram
7
PIR motion detection
Manually record
Power
Audio on/off
PIR USB
micro SD
Lens
6pcs invisible LED light

installing the microSD card Removing the micro SD card
Before Using Your Conbrov T11 Camera
1. Charging your camera
(1) The camera power must be off before charging.
(2) Plug the USB cable both in the camera and in
a computer USB port or a 5V/1A adaptor (not
included). The yellow LED is on while charging.
The charge time is about three to four hours.
(3) The yellow LED turns off when the camera is
fully charged.
8
Yellow indicator Off
Steady yellow
Off
Flashing blue and red
Charging
Fully charged
Low power
2. Installing the microSD card

Before Using Your Conbrov T11 Camera
9
Caution! Format the microSD before use. Doing
this, however, will remove all data from the card.
Make sure to back up any data before formatting
(applicable to Windows system ONLY)
The Camera records video only when microSD
is installed.
(1) The device supports a Class 10 microSD card which
has capacity of more than 8GB and up to 32GB.
(2) Do not remove the microSD card during operation.
it will damage both the memory card and camera.
(3) Push the microSD card into the slot gently until it
click into place.The card only fits one way, so do
not force the card into the port.
(4) To remove the microSD card, make sure the camera
is OFF. Press down on the microSD and it will pop
up,you can then pull it out easily.

New
Open
Save
Save as
Page settings
Print
Exit
File Edit Format View Help
SETTIME.TXT
SETTIME
Before Using Your Conbrov T11 Camera
3.Setting the date and time
Turn on the camera and connect it to PC with the
included USB cable, after about 12 seconds, the
disc icon will appear on your computer, then
please open SETTIME.TXT
Note:Please record a video first before setting
the date and time.
Open the SETTIME.TXT file,The following menu
will be displayed:
SETTIME.TXT
file Edit Format View Help
2016-07-15, 23:59:59
yes
yyyy-mm-dd, hh:mm:ss
yes: loop recording on microSD
no: no loop recording
Time format: File name
Modify the date and time on the computer.
After setting date and time, click on “File” and
then on “Save”.
10

Before Using Your Conbrov T11 Camera
Note: If you cannot find the file SETTIME.TXT
after opening the microSD on the computer, please
record a video clip to activate the card and set the
date and time again. The date and time will remain
accurate unless the battery has been depleted for
long time.
11

How to Use Your Conbrov T11 Camera
1.Turning the Camera On/Off
(1) Press and hold the to switch the camera on.
The LED will light up blue, which indicates that
it is in standby mode.
(2) Press and hold the to switch the camera off.
The LED will flash alternating red and blue and
then turn off.
ON lights up blue
and the camera is
in standby mode
OFF flashes alternating
red and blue and then
turns off
Note: If the camera switches off automatically,
there are two reasons:
1. The battery power is too low and the camera
must be charged.
2. The camera has been in standby mode without
any operation for longer than 1 minute. In this
case, the camera switches off to save battery
power.
2. How to Record a Video
1)Continuous Manual Recording(Press after the
Camera is powered on)
Press the LED will flash blue for 3 seconds
and then goes off, A 10-minute video clip will
be recorded .
12
2S

How to Use Your Conbrov T11 Camera
Press again, the blue LED will be on. The
device will save the video to the micro SD card
and stop recording .
2)Motion Detection Recording (Press after the
Camera is powered on)
When Motion Detection is activated, recording
will begin when there is movement in front of the
camera（not further than25 feet）.The motion
sensor detects the environment every 1~ 2
minutes.The camera will begin recording again
when it detects new movement.
The Red LED indicator is always on when in
motion detection mode.
Press the blue LED will flash once and the
red LED stays on, the device begins to record
video.
13

How to Use Your Conbrov T11 Camera
Press again, the blue and red LED will flash
then go off. The device will save the video to the
micro SD card and stop recording .
Note:The rotating Camera lens and LED allow you
to rotate the lens for greater placement options.
The PIR detector must not be covered or it will not
be able to detect motion.
3.How to Switch Into Night Vision
Whether under manually recording or PIR activated
recording, when ambient light brightness is lower
than 10LUX, the camera will automatically switch
into night vision and the video is black and white.
4.How to Play the Video
(1) Connect the T11 camera to computer, press and
hold the Power Button for 2 seconds or take out
the microSD, insert it into the card reader (not
included), then connect the card reader to
computer.
12S power on
2
US B2.0
14
(2) After a few seconds, there will be a removable
disk shown on computer. Open it, and then
you'll see the Video file. Open it to play the
videos.

LED status
Charging
No MicroSD installed
No operation for 60
seconds
Switching off in standby
mode
Switching off during
video recording
Continuous recording
Red LED indicator
always on
Operation LED status indication
Steady yellow and turns
off once fully charged
LED flashes blue for 10
seconds, and the camera
turns off
Blue LED turns off
(camera turns off)
LED flashes alternately
red and blue
LED flashes alternately
red and blue
LED flashes blue 3
times and turns off
LED indicator always on
15

Technical specifications
Dimensions 65x35x28mm
Net weight 53g
Battery LiPo
Stand-by power consumption 10uA
PIR detection angle 60 degrees
PIR detection distance 5-10 meters
Camera angle 120 degrees
Max PIR stand-by time 1 year
Day time recording power
consumption 220mA
Max day time recording time 4 hours
Night vision recording power
consumption
Max night vision continuously
recording time
Full-Charging time 3.5 hours
Resolution 720PFPS 30FPS
PIR MD video recording
Record continuously
Max storage capacity
microSD card
Loop recording optional
650mA
1.5 hours
about 10 minutes
per file
32GB
16
about 2 minutes
per file

FAQs
1.Q: Why is the camera charging so slowly?
A: The charging current is too low. Charge with 5V/1A.
This camera built-in 1000mah battery.
2.Q:When power on the camera, the blue light flash
all the time, and can not record.
A:Regarding to your problem, When the blue lights
blinking continuously, it shows that it can not read the
sd card.
3. Q:Can you access camera video from cell phone?
A: NO,This camera can't view video from cell phone.
4. Q: The blue LED flashes fast, video cannot be saved.
A: The memory card may be damaged, pls replace the
microSD card.
5.Q:The motion detection is slow. Is there a way to
adjust the motion detection so they will start
recording faster?
A:When you press MD button, and it takes sometime to
detect the environment, the time was influenced by
the environment. you could walk frequently in front of
the camera to make the camera enter the MD mode
faster .
6. Q: Playback mode seems to be in slow motion, not
smooth, broken up.
A: It may be due to the slow read and write speed of
your microSD card. We recommend using a
high-quality Class 10 microSD card with 16GB
capacity.
17

FAQs
7.Q:Can it record though the window?
A:you can record through the window manually. But
Motion recording is not working properly through a
window.The window will affect motion sensing as the
temperature of the window itself will mask
temperature changes occurring outside.
8. Q:What does 10 minutes per file mean? Can not it
record one 1 hours continuously?
A:Each file of 10 minutes means that it continuously
records 1 hour, and it will save 6 files,per file has 10
minutes.When you view video on computer ,you can
see video is continuous.
9.Q:Why can't I play back the video on computer?
A:We recommend using VLC player for playback If you
use a Mac. If you use a window PC, please try KMP
player.
10.Q:Why is my camera not being recognized on the
computer?
A:Please turn on the camera first, then connect the
camera to the computer via USB cable.(The blue
LED indicator will stay on and the red indicator will
flash).
Or please use other microSD card, please format
the card to FAT32 on window computer. Please
reset the camera and try again.
11. Q: Why am I coming home to hundreds of 1-2
minute clips all with no motion being recorded?
A: Because use MD mode,camera will through PIR
to record, advice you not put the camera on a lot of
windy and Air conditioning mouth.
18