Concept Pro CP-HSD20-AHD User manual

AHD HIGH SPEED DOME SERIES QUICK START GUIDE
CP-HSD20/30-AHD
6-in-1 PTZ
QUICK START GUIDE

AHD HIGH SPEED DOME SERIES QUICK START GUIDE
1WHAT’S IN THE BOX?
Packaging Contents
Speed Dome Camera x1 9-Pin Terminal Block x 1 Quick Start Guide x1
Bracket x1 Anchor Bolt x 4 Screwdriver x1
Hex Key x 1 Mounting Template x 1 User Manual USB x1
Gloves x1
2INSTALLATION
Install the Speed Dome Camera in 3 Steps
1. Use the mounting template sheet to drill holes in the mounting surface, then ax
the included bracket to the surface
2. Connect the safety lanyard between the camera and bracket, then connect all
required cables to the camera bracket PCB into power, telemetry and alarms where
required.
3. Twist the camera into the bracket and tighten the xing screws.
3WALL MOUNT INSTALLATION
1. Drill holes and ax wall bracket to surface and pass cable through to junction box
2. Congure DIP switches for ID, baud rate, video output then twist on dome and
secure to wall bracket
3. Attach all cables to junction box and tighten all xing screws

AHD HIGH SPEED DOME SERIES QUICK START GUIDE
5SMART KEY OPERATION
Joystick right = Conrm & Save
Joystick left = Exit & Cancel
Joystick up/down = Navigate up /down or change value
6CONFIGURING THE CAMERA
Camera Connections
3
Alarm Input Terminal Block
1BNC 1&2 Video Output
- HD-SDI/HD-AHD
2
4
Alarm Output Terminal Block
5
DC 12V/ AC 24V Power Input
RS-485 Connector
Camera Setting Set Switch
7
Address ID Set Switch
6
8
DC12V Output
CablingBNC1
1
2
3
Speaker
Mic.
ALARM INPUT
GND1 2 3 4 5 6 7 8
COM
In 1
In 8
OUT1 OUT2 OUT3 OUT4
4
5
7
6
8
BNC2
4OSD MENU
Press ‘PRESET’ + 95 to enter the camera OSD menu
VIDEO SETUP
PTZ SETUP
ACTION SETUP
OSD SETUP
SYSTEM SETUP
INFORMATION
EXIT
OFF
SEMT AUTO
AUTO
50
50
AUTO
U/D
AUTO
FLICKER
2
2
FLICKER
HLC ON
2
2
2
FOCUS MODE
D-ZOOM
WHITE BALANCE
_RED ADJ
_BLUE ADJ
DAY/NIGHT
SHUTTER MODE
_SHUTTER
IRIS MODE
_IRIS
GAIN MODE
BRIGHTNESS
BACKLIGHT
SENS -UP
_SENS UP LIMIT
COLOR LEVEL>>

AHD HIGH SPEED DOME SERIES QUICK START GUIDE
6CONFIGURING THE CAMERA
DIP Switch Setup
1. VIDEO OUTPUT
BNC1: Analogue HD connector, for AHD/TVI/CVI/CVBS output.
BNC2: SDI connector, for EX-SDI/HD-SDI output.
2. Address ID Switch
1 2 3 4 5 6 7 8
ON
ON
OFF
ON
ON
ON
ON
OFF
OFF
OFF
---
OFF
ON
ON
OFF
ON
ON
OFF
ON
OFF
---
OFF
OFF
OFF
ON
ON
ON
ON
ON
OFF
---
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
ON
---
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
---
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
---
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
---
OFF
OFF
OFF
OFF
OFF
ON
OFF
OFF
OFF
1
---
2
3
5
7
4
255
6
8
-
1
12345678
2
D I P
4 8 1 6 3 2 6 4 128Va l I D
Factory default
switch positions
Speed dome ID is set using
standard binary notation
1 2 4 8 16 32 65 128
Note: ID 0 should not be used. Where multiple speed domes
are connected, a unique ID must be assigned to each one.
3. SET SWITCHES
DIP No. 1 and 2 congures the baud rate as follows:
1 2 3 4 5 6 7 8
ON
OFF
ON
OFF
Factory default
switch positions
NO.1
OFF
OFF
ON
NO.2
2400
4800
9600
Rat e
DIP No. 3 and 4 congures the video output as follows:
OFF
ON
ON
OFF
NO.3
OFF
OFF
ON
ON
NO.4
AHD
CVBS/SDI
CVI
TVI
Output
Switch No. 5:
ON: NTSC OFF: PAL
Switch No. 6:
ON: 30FPS (Default)
Switch No. 7:
ON: EX-SDI OFF: HD-SDI
Switch No. 8:
RS485 matching resistance switch (120Ω). Default setting is OFF.