Concept Pro VCP7236-AHD User manual

OSD
SPECIFICATION
OSD Controller
UP - CVBS
LEFT - AHD
MENU / ENTER
DOWN - CVI
RIGHT - TVI
2DNR
D-WDR
1. This installation should be completed by qualified service personnel and
should abide by all local codes and laws.
2. Do not disassemble the camera - this is to prevent electronic shock
and/or malfunction. Do not loosen any screws on the camera body.
3. Do not touch the front glass directly. If necessary, use a soft cloth to wipe off
dust or debris.
4. Avoid installation on surfaces subjected to frequent vibration or shocks.
5. Do not operate the camera beyond its temperature range or power source
ratings.
6. Should any damage or suspected damage occur, shutdown the power
source, unplug and contact your service provider.
7. Do not install the camera under unstable lighting conditions. Severe
lighting change or flicker can cause the camera to work improperly.
8. Never use the camera near a gas or oil leak.
9. Do not drop the camera or subject the unit to physical shocks.
10. Never keep the camera facing directly to strong light.
11. Do not install near devices which emit a strong electro-magnetic field.
12. Unplug the camera from the power source before maintenance.
13. Use a soft cloth only for cleaning.
14. If the camera may be exposed to weather conditions, dust particles or
moisture install in an IP rated housing suitable to the conditions.
PLEASE FOLLOW THE ABOVE CAUTIONS – FAILURE TO DO SO MAY
INVALIDATE THE WARRANTY OR CAUSE SERIOUS INJURY.
CAUTION
VCP7236-AHD
AHD Body Camera
USER MANUAL
Design and specification are subject to change without notice.
1/3 INCH SONY CMOS
2MP
PAL
PROGRESSIVE
INTERNAL
25fps
AHD/TVI/CVI/CVBS
1920(H)x1080(V)
0.001Lux @ (F1.2,AGC ON)
n/a
MANUAL 2.8-12mm VARIFOCAL
TRUE COLOUR/MONO ICR
OFF/ON(Level 0-8)/Auto
≥50dB
1/50-1/50,000s
ATW/AWC-SET/Indoor/Outdoor/MANUAL
LEVEL 0-15
BLC/HLC/OFF
2D/3D
YES
YES
1.0Vpp, 75 Ω BNC
>300m via 75 Ω coaxial cable
12VDC±10%
4.5W
-10℃~+55℃
0% - 85% RH
64mm x 65mm x 150mm
300g
CE / FCC
SENSOR
SENSOR RESOLUTION
SIGNAL SYSTEM
SCANNING SYSTEM
SYNC. MODE
FRAME RATE
VIDEO FORMATS
EFFECTIVE RESOLUTION
MIN. ILLUMINATION (LED OFF)
MIN. ILLUMINATION (LED ON)
LENS
DAY & NIGHT
DIGITAL WDR
S/N RATIO
ELECTRONIC SHUTTER
WHITE BALANCE
GAIN
AE MODES
DIGITAL NOISE REDUCTION
PRIVACY MASKING
MOTION DETECTION
VIDEO OUTPUT
TRANSMISSION RANGE
SUPPLY VOLTAGE
POWER CONSUMPTION (MAX)
OPERATING TEMPERATURE
OPERATING HUMIDITY
DIMENSIONS
WEIGHT
CERTIFICATIONS
VIDEO OUT
VD
DC
P. I
DC12V/AC24V F.G
POWER LED
POWER
VIDEO OUT JACK
MAIN MENU
AE
WB
DAY-NIGHT
VIDEO SETTING
LANGUAGE:
RESET
SAVE-EXIT
EXIT
⏎
⏎
⏎
⏎
ENGLISH, CHINESE, SPANISH, KOREAN, ITALIAN
⏎
⏎
VIDEO SETTING
CONTRAST:
SHARPNESS:
COLOR GAIN:
DNR:
IMAGE SIZE:
FORMAT:
RETURN
1-50
1-20
1-20
1-15
1080P, 720P
PAL, NTSC
⏎
DAY / NIGHT
MODE:
RETURN
EXT, AUTO, COLOR, B/W
⏎
WB
MODE:
RGAIN
(MODE = MWB):
BGAIN
(MODE = MWB):
RETURN
ATW, MWB
⏎
EXPOSURE
BRIGHTNESS:
EXPOSURE MODE:
LV (EXPOSURE
MODE = BLC):
GAIN:
RETURN
1-20
GLOBE, CENTER, BLC, FLC
1-8
⏎
0-8
1-16
1-16

INSTALLATION CONNECTION EXAMPLE
LENS ADJUSTMENTS
DIMENSIONS
IMPORTANT: ENSURE ALL CAUTIONARY PROCEDURES ARE
OBSERVED DURING INSTALLATION.
It is recommended the VCP7236-AHD is tested during the most
demanding environmental conditions such as low light or bright
sunlight to ensure continuity of effective CCTV monitoring.
Remove the camera unit carefully from the box, reserving the
accessory contents in a safe place.
Point the Camera towards the intended area to be monitored.
Check the power supply voltage and connect your power supply into
the power port on the Camera.
nAttach a test monitor to the video out BNC port and adjust the lens
to give the required image
nAdjust the Camera picture using the OSD menu as necessary.
TROUBLESHOOTING
Ensure all power and cable connections are correct between the
Camera, power source, monitor, telemetry devices and DVR if used
Example
PSU
Built in Lens
Top Cover
Zoom Handle
Focus Handle
150mm
58mm
7mm
38mm
38mm
51mm
42mm
64mm
02/17 - REV. 1