CONCH VU-50K User manual

(rch vu-50K,vu-51K,VU-52K,VU-53K
IU-5OK > IU-51K > IU-52K > IU-53K
W Panel Description
Status
Indicator
Zeroing
CONCH
E Settings
To Set Comparing Value and Delay Time, press “mode” to activate.
(* Different models or output modes apply different settings, e.g. the setting below does not apply to
VUL5O Kooos.)
SP- |
(mode
Output Value Setting: (SP-1, SP-2,SP-3)
When PV meets the output condition, relay
S P ra g [roa] makes output. (Output mode is
g p J programmable.) Press [shit | to start setting.
iis mode]
E re { [roae] RELAY Output Delay Time: (tr1,tr2,tr3)
Out1, Out2, Out3 output after a delay time.
Range: 0.1 - 9.9sec. Press “shift” to adjust.
Er-c| ed
E pe J M [ma] End Setting
E Forced Zero, Hold, Peak Hold, Output Mode, Teaching
Mode, Decimal Setting
for 3sec. to activate settings.)
Decimal Setting (Point)
Pont
To set decimal place of PV,
press to adjust.
End Setting
mode]
Control Mode Setting (i
iN
Hold (hold): When Terminal 11 & 12 are
input with an NPN signal, “hold” lamp lit
and PV frozen. At this moment, relay
output will not be affected by metered
signals.
mode]
Peak Hold (peak): When Terminal 11 &
12 are input with an NPN signal, “MAX”
lamp lit, displays and freezes the max
value. At this moment, relay output is
still affected by metered signals.
PY Zeroing (Zero): When terminal 11
&12 are input with an NPN signal, PV
resets to zero, and “ZERO” lamp lit.
Applies to deduct the scrap value with
data memory, working the same with
“zero” key on the panel. To remove
zeroing memory, hold “zero” for 2sec.
and until “zero” lamp goes off.
Output Mode Setting (out)
out
U-53Kxx applies] VU-52Kxx applies | VU-51Kxx applies
mode
HHH _
msan H” fa
HHL
meng
(3) ine" a
HH
UNA in "H"
HL G
amn
(2) ine
HLL LL L
GNR in“
™H" mode
(1) in “H”
(23(3) in *U” s
T]
LL
=
HGL
KI
|
m-
{1)(2)(3) alli
(1) in “HY
(2}in “G”
(3) in “e
[shift `
End Setting
User’s Manual
Teaching Mode Setting (teach)
Doc. No.: T10-00080
Date: 2015/7/14
Version: V1.0
initial Input Value (in-1): Press |shift
FERCH]
E Teaching Curve
rrode|
to start setting from the panel. If [anit
is held, then the meter continues to
read in input signals until Ẹri] is
released.
Initial Value Display (ds-1): Press (shit
to start setting from the panel.
n-e
Final input Signal (in-2); Press [ehit] to
start setting from the panel. tf (nit) is
mode]
a
d5-2
held, then the meter continues to
read in input signals until Grin) is
released.
Final Value Display (ds-2); Press [shitt
to start setting from the panel.
DISPLAY
[roge] End Setting
SIGNAL IN
E Output Curve
H mode
DISPLAY Es
HH mode}
DISPLAY
Lmode
DISPLAY
[u-s1 Kxx applies
HL mode
SIGNAL IN
m
OUT
U-52xx applies
LL mode
DISPLAY
AEN E E
oam y in
HHH mode
SIGNALIN
s a
OuTT tr OUTI
~a tr~
ouT2 ouT2
U-53Kxx applies
LLL mode HGL mode

(Nch vu-50K.vu-51k,vU-52K,VU-53K User's Manual
IU-5OK > |U-51K > IU-52K + IU-53K
E
Specification
Hf
Panel
Dimension
&
Cutout
Model No. | (I) VU-50Koo00 | (1) VU-51 Koxx | (1) VU- 52 Koo0ac | (1) VU-53 Ko000c
AC 110V /220V - 60/50Hz +10% PANEL—CUT
| —=
Display Range |-19999 ~ 19999 48.0| |e F398 | 440
Input Control i i Y H
DC Voltage (VU-SXKDChod | —$<—
(00=0~1 00Mv,01=0~199.99Mv,02=0~1 .9999V,03=0~19.999V,
104=0~199.99v - -————91.2—___+
IAC Voltage (VU-SXKAChod 109
(00=0~1 9999v,01=0~19.999v,02=0~60v, 03=0~199.99v
Input Type |94=0~600v -
E Installation Diagram
A, B Contact A, B Contact
A iset 2sets
-19999 ~ PANEL
| 79999 E 9999 ~ 19999
+12v + 80MA MAX.
[Operating Temp. |-10 to 55°C with no icing
[Storage Temp. |-25 to 65°C_with no icing
Relative Humidity 135% to 85% RH
maar . c mie
E Wiring Diagram
[VU-SIKxx -l
HOLD
©
=]
i
E
Fi
;
= 56 TB [9 ponam
+2V HI LO OV
i i [5] BRT
716[5|4|3|2[1
Ed] Lea
[VU-S2Kxx
HOLD
a0
INPUT-
"=
a
zero a [8 |9 [101 1[12]13]14]
+2V HI LO OV OUTI
QUT2 SRR Vioacy,sovsore
[7]6[5]4][3[2]1
E Tov.
220V
MUSK |
HOLD
© Ə
INPUT-
Aai
=
zero +a TB] Q [1 Off 1]12]13]14]
+12v HI LO OV Ou
To (60) SOURCE
OUTS OUT2 220AC WTIOACV,50/60H2
[7[6[5]4]3]2|1
=e = 3] C Tov.
0