Concourse HS-VA3800 User manual

FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by Digital Security Controls Ltd. could void your
authority to use this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio commu-
nications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turn-
ing the equipment off and on, the user is encouraged to try to correct the interference by one or more of the fol-
lowing measures:
Re-orient the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
The user may find the following booklet prepared by the FCC useful: “How to Identify and Resolve Radio/Tele-
vision Interference Problems”. This booklet is available from the U.S. Government Printing Office, Washington
D.C. 20402, Stock # 004-000-00345-4.
Warranty
Digital Security Controls Ltd. warrants that for a period of 12 months from the date of purchase, the product shall be free
of defects in materials and workmanship under normal use and that in fulfillment of any breach of such warranty, Digital
Security Controls Ltd. shall, at its option, repair or replace the defective equipment upon return of the equipment to its
repair depot. This warranty applies only to defects in parts and workmanship and not to damage incurred in shipping or
handling, or damage due to causes beyond the control of Digital Security Controls Ltd. such as lightning, excessive volt-
age, mechanical shock, water damage, or damage arising out of abuse, alteration or improper application of the equip-
ment.
The foregoing warranty shall apply only to the original buyer, and is and shall be in lieu of any and all other warranties,
whether expressed or implied and of all other obligations or liabilities on the part of Digital Security Controls Ltd. Digital
Security Controls Ltd. neither assumes, nor authorizes any other person purporting to act on its behalf to modify or to
change this warranty, nor to assume for it any other warranty or liability concerning this product.
In no event shall Digital Security Controls Ltd. be liable for any direct, indirect or consequential damages, loss of antici-
pated profits, loss of time or any other losses incurred by the buyer in connection with the purchase, installation or opera-
tion or failure of this product.
WARNING: Digital Security Controls Ltd. recommends that the entire system be completely tested on a regular basis.
However, despite frequent testing, and due to, but not limited to, criminal tampering or electrical disruption, it is possible
for this product to fail to perform as expected
IMPORTANT INFORMATION: Changes or modifications not expressly approved by Digital Security Controls Ltd.
could void the user’s authority to operate this equipment.
2003 Digital Security Controls Ltd.
Toronto, Canada
1-800-387-3630 •www.dsc.com •Printed in Canada
HS-VA3800
3x8 Video Amplifier
Installation Instructions
Introduction
The HS-VA3800 3x8 Video Amplifier module provides amplification and splitting of 3
Video inputs to 8 video outputs. A return path is provided for the use of broad band
modems. This module can be installed in Concourse Home Systems cabinets (HS-
CAB1000, HS-CAB3000 and HS-CAB4000) using the supplied mounting hardware.
Figure 1, HS-VA3800 Video Amplifier/Combiner
29034662R001
Specifications
Connector & impedance
Input Capability:
Frequency Range:
Number of ports:
Forward gain (dB Max):
Return Path Loss (dBMax):
F-type, 75 ohms
117dBuV at 1dB compression
Forward Path 54- 1000MHz Reverse Path 5-42MHz
Inputs - 3, Outputs - 8
CATV/ANT IN + 4dB, AUX IN +2dB
12 dB
Contents of Package
Before installing this module, verify that the package contains the following:
• Qty (1)....ASKA MDA38R Drop Amplifier
• Qty (1)....Video Combiner bracket
• Qty (1)....Power Supply 12V
DC , 300mA
• Qty (2)....Hardware pack containing two ½” phillips flathead screws
• Qty (1)....Installation Instructions

Installation - Module
1. Locate a suitable mounting location for the HS-VA3800 Video Amplifier/Combiner
inside the cabinet. Note that the unit can be installed in various positions, the F-
type connectors may face the top or the bottom of the cabinet.
2. Mount MDA-38R Drop Amplifier on video combiner bracket using the 2 self-tapping
sheet metal screws provided.
3. Align the two mounting pins with the holes in the back of the cabinet and insert as
indicated in figure 2.
4. Snap the module in place by pressing both sides towards the back of the cabinet.
5. Secure the metal bracket to the cabinet using the two screws provided.
Installation - Wiring
The following requirements for installation of coaxial cable must be met for proper oper-
ation of connected equipment.
•DoNOT strip off cable sheathing more than required for proper termination.
•DoNOT kink or knot cable.
•DoNOT crush cable with cable ties.
•DoNOT splice cable.
•DoNOT bend cable at right angles or make any other sharp bends. All cable bends
must have a minimum of a 2" radius.
Figure 2, Installation
Installation - Wiring (Contd.)
1. Run RG6 coaxial cable from each source/destination through the cabinet
raceway to the HS-VA3800 Amplifier module. Label cables at both ends for
identification. Terminate cables with "F" style connectors.
Note: Ensure that cable source/destinations are "F" style jacks mounted in an
appropriate wall plate. If using a multiple wall outlet then label the jacks
accordingly.
2. Connect source/destination ends of the cables to the "F" style jacks. Connect the
terminated drops to the HS-VA3800 Video Amplifer module terminals labelled
"OUTPUTS".
3. Terminate unused output terminals on the HS-VA3800 Video Amplifer module with
75 ohm terminators (not supplied).
4. Locate a suitable 110VAC receptacle for placement of the wall-mount transformer. If
necessary have a qualified electrician install a 110VAC receptacle close to the panel.
5. Route RG6 coaxial cable from the power supply at the 110 VAC receptacle into the
cabinet to the HS-VA3800 Video Amplifer module.
6. Terminate each each end of the coaxial cable using a standard "F" style connector.
Connect the cable to the HS-VA3800 Video Amplifer module terminal labelled 'PWR
- IN' and to the power supply.
7. Plug in the power supply and test all connections to confirm proper installation and
termination.
5
HS-CAB1000, HS-CAB3000
or HS-CAB4000 cabinet
1
Mount the MDA-38R Drop Amplifier as
shown to ensure that there is sufficient
clearance for the F-type connectors.
NOTE:
3