Connect IT CI-21 User manual

This product is designed to mount flat panel televisions weighing up to 75kg/165lbs to a vertical firm wall.
Safety Warning: Be careful to make sure there are no missing or defective parts. Never use defective parts. Improper
installation may cause damage or serious injury.
Note: The included hardware is for mounting on walls . If you are uncertain about the nature of your wall, consult an
expert. Please consult your hardware or installation professional for proper mounting to other types or walls. The
supplied hardware is not for steel.
Forbidden Instruction: Do not mount onto plasterboard or panelled walls.
ASSEMBLY INSTRUCTIONS
FOR FIXED FLAT PANEL WALL MOUNT
SUPPLIED PARTS: Supplied joint parts are exclusive for using in this product. Other joint parts are forbidden to use on this product. If any parts are
missing or faulty, telephone the special franchiser for a replacement.
12
3
Mounting the Wooden Wall Plate
Important! For safety, the mount must be secured to two
adjacent wood studs on least 16" apart.
1. Using a stud finder, locate and mark two adjacent studs
for securing the mount.
2. Place the wall plate against the wall and level it using the
bubble guide.
3. Make two locations (two per stud) on the wall where the
mount will be secured.
4. Remove the wall plate and drill a (4mm) pilot hole on each
location using an electric drill.
5. With the help of another person, replace the wall plate and fix
it to the wall using the Lag Bolts and Lag Bolt washers provided.
6. Do not over-tighten the bolts and do not release the wall plate until all screws are secure.
Mounting the Concrete Wall Plate
1. Place the wall plate against the wall and level it using the bubble guide.
2. With the help of another person, mark off four (4) locations for fixing the
mount to the wall.
3. Place the wall plate aside and drill a hole at each location using a 3/8"
(10mm) masonry bit. Remove any excess dust form the holes.
4. Insert one Concrete Anchor into each hole. A hammer can be
used to lightly tap the anchors into place if necessary.
5. With the help of another person, replace the wall plate
and fix it to the wall using the Lag Bolts and Lag Bolt
Washers provided.
6. Do not over-tighten the bolts and do not release the wall
plate until all screws are secure.
Final Installation and Adjustment
1. With the help of another person, carefully lift your display and place it on the wall plate. Do not release the display until the
mounting arms have securely hooked onto the mount.
2. Move the safety lock as the picture shows and tighten the two screws to fix the safety lock.
Attaching the Arms to the Display
Important! Use extra care during this part of the installation. If possible, avoid placing your display face down as it may
damage the viewing surface. Note: Your mount comes with a selection of bolt diameters and lengths to accommodate a
wide variety of display models. Note all of the hardware in the kit will be used.
1. Determine the correct length of bolt to use with your display by first examining the back of you display.
A. If your display has a flat back, you will use one of the shorter bolts from the hardware kit.
B. If your display has a curved or recessed back, you will use one of the longer bolts along with a spacer.
2. Determine the correct diameter of bolt to use by carefully trying one bolt each from the hardware kit. Do not force any
of the bolts-if you feel resistance stop immediately and by a smaller diameter bolt.
3. Attach the arms to the back of your display using the bolts identified along with corresponding washers.
A. If you are using the M4 or M5 bolts, you will also need to use the small hole of the washers n . If you are using the M6
or M8 bolts, you will also need to use the big hole of the washers n .
B. If you are using one of the longer bolts on a display with a curved recessed back, you will also use a Spacer. Use the
Small Spacer for M4, M5and M6 bolts and the Large Spacer for M8 bolts.
4. Make sure all screws are secure, but do not over-tighten them.
a
d
g
j
M4x30mm Screw
x6
Big Spacer
x4
Hardware kit
M5x30mm Screw
M6x30mm Screw M8x25mm Screw M8x40mm Screw
Concrete Anchor 6mm Lag Bolt
Small Spacer Lag Bolt Washer
Washer
x4
x4
x4 x4
x4
x4
bc
ef
hi
k
x6
x4
x4
l
x6
M5x10mm Screw
Assemble the bracket
1.Find out the 4 parts as the picture shows.
2.Assembling the 4 parts by using 4 screws(c)
as the diagram-4 shows.
3.Make sure the bracket was joined together
firmly.
M4x12mm Screw
M5x12mm Screw M6x12mm Screw
x4
x4 x4
mno
Diagram-1
Diagram-2
Diagram-3
Diagram-6
Diagram-4
c
Diagram-7 Diagram-8 Diagram-9
ok
j
Diagram-5
16"
k
o
CI-21

12
3
a
d
g
j
M4x30mm šroub
x6
SRGNODGDþ
x4
6H]QDPGtOĤ
M5x30mm šroub
M6x30mm šroub M8x25mm šroub M8x40mm šroub
KPRåGLQND 6mm šroub
SRGNODGDþ SRGORåND
SRGORåND
x4
x4
x4 x4
x4
x4
bc
ef
hL
k
x6
x4
x4
l
x6
M5x10mm šroub
M4x12mm šroub
M5x12mm šroub M6x12mm šroub
x4
x4 x4
mQo
'LDJUDP
'LDJUDP
'LDJUDP
'LDJUDP
'LDJUDP
c
'LDJUDP 'LDJUDP 'LDJUDP
ok
j
'LDJUDP
40 cm
k
o
7HQWRSURGXNWVORXåtNXFK\FHQtSORFKpREUD]RYN\RPD[LPiOQtYi]HNJNHVWČQČ
%H]SHþQRVWQtXSR]RUQČQt8MLVWČWHVHåHEDOHQtREVDKXMHYHãNHUpGtO\DþiVWLDXMLVWČWHVHåHåiGQê]GtOĤQHQt
YDGQêQHERSRãNR]HQê1LNG\QHSRXåtYHMWHSRãNR]HQpGtO\âSDWQiLQVWDODFHPĤåH]SĤVRELWYiåQp]UDQČQtQHER
SRQLþHQtXFK\FHQpREUD]RYN\
3R]QiPND'UåiNDSĜLORåHQpGtO\MVRXXUþHQ\NXFK\FHQtNH]GL]SOQČQêFKFLKHOEHWRQXQHERGRWYUGpKRGĜHYD
-HVWOLåHGUåiNLQVWDOXMHWHGR]GL]WYUGpKRGĜHYDQHSRXåtYHMWHåiGQpKPRåGLQN\3RNXGVLQHMVWHMLVWL]MDNpKR
PDWHULiOXYDãH]GLMVRXSRUDćWHVHVRGERUQtNHP2EUDĢWHVHQDRGERUQtNDLYSĜtSDGČMLQpKRPDWHULiOX]GLGRNWHUp
FKFHWHGUåiNLQVWDORYDW3ĜLORåHQpãURXE\QHMVRXY\UREHQ\]RFHOL
8SR]RUQČQt1HPRQWXMWHGUåiNGR]GL]HViGURNDUWRQXQHERGR]GLREORåHQpNDFKOLþNDPL
NÁVOD K INSTALACI
),;1Ë+2'5äÈ.83523/2&+e2%5$=29.<
3ĜLORåHQpGtO\DãURXE\MVRXY\UREHQ\VSHFLHOQČNSRXåLWtXWRKRWRSURGXNWX3RXåLWtMLQêFKQHåSĜLORåHQêFKGtOĤMH]DNi]iQR3RNXGMVRXQČMDNp
GtO\SRQLþHQ\QHERFK\EtNRQWDNWXMWHYêUREFHSURQiKUDGXþLYêPČQX
DŮLEŽITÉ: Věnujte zvýšenou pozornost této části instalace. Pokud je to možné vyvarujte se položení obrazovky displejem na zem aby jste zabránili
poškození. V balení k držáku je přidán velký výběr rozměrů a velikostí šroubů aby vyhovoval velkému množství výběru obrazovek.
1. Určete správnou velikost šroubu určeného k namontování vaší obrazovky ze zadní strany televize.
a. pokud má vaše obrazovka plochou zadní stranu použijte jeden z kratších šroubů
b. pokud má vaše obrazovka zakřivenou nebo zapuštěnou zadní stranu použijte jeden z delších šroubů společně s podkladačem.
2. Určete správný průměr šroubu opatrným zkoušením každého šroubu z přiloženého balení. Nepoužívejte hrubé síly a pokud cítíte odpor, okamžitě
ukončete pokus a zkuste šroub s menším průměrem.
3. Připojte rameno k zadní části obrazovky pomocí správných šroubů a podložek. Pokud použijete šrouby M4, M5, M6 nebo M8 budete také potřebovat
podložku M. Pokud použijete jeden z delších šroubů pro obrazovku se zakřivenou zadní stranou budete také potřebovat použít malý podkladač pro
šrouby M4 a M5 a velký podkladač pro šrouby M6 a M8.
4. Ujistěte se, že šrouby jsou pevně přišroubované, ale dejte pozor, aby jste je nepřetáhli.
5. Hlavičky šroubů by měli směřovat ven od obrazovky.
6HVWDYHQtGUåiNX
1DMGČWHþiVWLMDNMHYLGČWQDREUi]NX
6ORåWHþiVWLGRKURPDG\SRPRFLãURXEĤ&MDN
MHYLGČWQDGLDJUDPX
8MLVWČWHVHåHMHGUåiNSHYQČVSRMHQ
0RQWiåGRGĜHYČQpVWČQ\
'ĤOHåLWp3UREH]SHþQpXFK\FHQtGUåiNPXVtEêWQDYUWiQGR
GYRXGĜHYČQêFKSĜtþQêFKWUiPĤRGVHEHY]GiOHQêFK
QHMPpQČFP
8UþHWHPtVWRGYRXSĜtþQêFKWUiPĤSURXSHYQČQtGUåiNX
8PtVWČWHGUåiNXUþHQêNQDYUWiQtNHVWČQČD]DURYQHMWH
KRSRPRFtYHVWDYČQpYRGRYiK\
1DþUWQČWHQDNDåGpVWUDQČGYČPtVWDSURXPtVWČQtãURXEĤ
NGHEXGHGUåiNXFK\FHQ
2GHQGHMWHGUåiNDY\YUWHMWHPRQWiåQtRWYRU\YUWiNHPRSRORPČUX
PPQDNDåGpPY\]QDþHQpPPtVWČ
6SRPRFtGDOãtRVRE\QDPRQWXMWHGUåiNGRVWČQ\SRPRFtãURXEĤDSRGORåHNSĜLORåHQêFKYEDOHQt
'HMWHSR]RUDE\MVWHãURXE\QHSĜHWRþLO\DQHSRXãWČMWHGUåiNGRNXGQHQtSĜLãURXERYiQYãHPLãURXE\
0RQWiåGRFLKORYpQHEREHWRQRYp]GL
8PtVWČWHGUåiNXUþHQêNQDYUWiQtNHVWČQČD]DURYQHMWHSRPRFt
YHVWDYČQpYRGRYiK\
1DþUWQČWHPtVWDQD]GLNDPXPtVWtWHãURXE\
2GORåWHGUåiNDY\YUWHMWHPRQWiåQtRWYRU\YUWiNHPRSRORPČUXPP
'RNDåGpKRRWYRUXXPtVWČWHKPRåGLQNX3RNXGMHWR
QH]E\WQpPĤåHWHSRXåtWLNODGtYNRSUR]DVXQXWtKPRåGLQHN
6SRPRFtGDOãtRVRE\QDPRQWXMWHGUåiNGRVWČQ\SRPRFt
ãURX EĤD SRG ORå HNS ĜLO RåHQ êFK N E DOH Qt
'HMWHSR]RUDE\MVWHãURXE\QHSĜHWRþLO\DQHSRXãWČMWH
GUåi NGR NXG Q HQtS ĜLãUR XER YiQYãHPL ãUR XE\
)LQiOQtLQVWDODFHDQDVWDYHQt
6SRPRFtGDOãtRVRE\RSDWUQČ]GYLKQČWHREUD]RYNXDXPtVWČWHMLQDSĜLPRQWRYDQêGUåiNQHSRXãWČMWHREUD]RYNXGRNXG
VHREČUDPHQDEH]SHþQČQHXFK\WLODGRGUåiNXSĜLPRQWRYDQpPNH]GL
8WiKQČWHEH]SHþQRVWQtãURXE\GRSR]LFHNWHUiMHY\]QDþHQiQDGLDJUDPX
CI-21

MANUFACTURER
HERSTELLER
PRODUCENT
VÝROBCE
VÝROBCA
IT TRADE, a.s.
Poděbradská 786/65a
198 00 Praha 9-Hloubětín
Czech Republic
tel.: [phone]
ser[email protected]m
www.connectit-europe.com