Connect-Tek Transa PRO 17 User manual


Table of Contents
▓INTRODUCTION ....................................................................................................1
▓CONSOLE
Overview ...............................................................................................................3
Features ................................................................................................................3
Packing List...........................................................................................................4
Assembly...............................................................................................................6
Installation .............................................................................................................9
Front Panel..........................................................................................................10
Replaceable Keyboard and Touch Pad ............................................................... 11
LCD Specification ................................................................................................ 13
Please read this manual thoroughly and follow the Installation procedures to
prevent any damage to the product or any connecting device.

Transa PRO
‧
TransaView Console
1
------------------------ Introduction
The TransaView and Transa PRO offer the ultimate in styling and computer management. With a keyboard
mouse, TFT LCD panel and a KVM switch module housed in an industry standard 19" 1U-height rack drawer,
it saves you up to 1/3 of valuable real estate from a rack cabinet. Better yet, when the console is cascaded
with other KVM switch modules to increase server management capacity, you save even more!
All KVM switch modules come with a universal C-36 connector for connection between the console drawer
and a KVM switch module. This modularized design offers the maximum flexibility, as you can choose and
swap the modules to fit your needs. A KVM switch module can also be used as an independent KVM switch.
Theconsolecomesinthreeparts
A1U slide drawer with keyboard, touchpad,
and 15” LCD monitor.
BKVM Switch Module. (15 different
modules available, as shown on page 6)
CRear bracket and extension kit.
The console with
One-port PS/2 KVM switch module
It saves you up to 1/3 of valuable rack cabinet spaces
and acts as a space-saving console with keyboard,
mouse, and monitor. With an IKM001, it can be
connected to a PS/2 computer directly or to the console
ports of a PS/2 KVM switch.
This setup can be considered as a combination of a
PS/2 keyboard, a PS/2 mouse, and a LCD monitor.
The console with
1U-height KVM Switch Module
When a 1U-height KVM switch module is slid into the
rear side of the console drawer, the entire setup takes
1U space of a rack-cabinet.

Transa PRO
‧
TransaView Console
2
The console with
2U-height KVM Switch Module
Attached with a 2U-height KVM switch module, the setup
takes 1U-height for the console drawer and 2U-height for
the KVM switch module behind it.

Transa PRO
‧
TransaView Console
3
------------------------ Console
Overview
Three major models of consoles, Transa PRO 17, Transa PRO 15, and TransaView, are available with 17”
LCD panel, 15” LCD panel respectively. These three models share the same accessories (The KVM switch
modules and Rear Bracket Kits). The console is a 19” 1U drawer designed for applications where space is at
a premium, or CRT displays are undesirable. The Transa PRO 17 and Transa PRO 15 models support
replaceable keyboard and replaceable touch pad.
The drawer can be pulled out for operation from the rack and latched in the extended position. When not in
use, the display can be folded down, locked and secured while pushed in.
With different Rear bracket & extension kit, the console can be mounted on rack cabinet of various depths.
The console comes with standard PS/2 keyboard connector, PS/2 mouse connector and HDB15 VGA
connector for computer or KVM switch connection.
Model Transa PRO 17 Transa PRO 15 TransaView
Keyboard Replaceable Yes Yes No
Touch Pad Replaceable Yes Yes No
Module Selection Yes Yes Yes
H x W x D (mm) 502*445*43.5 502*445*43.5 485*445*43.5
Features
Modularized KVM switch design.
KVM switch modules are available for PS/2, USB, or Sun interface with 8-or 16-port.
Flip-open 15" or 17” LCD panel supports resolution 1024x768 or 1280x1024 respectively.
For managing computers with PS/2, USB, or Sun interface.
For rack cabinet with depth from 20"(50cm) and up (with appropriate Rear bracket & extension kit).
Standard 19" 1U rack drawer.
Ergonomic hand rest design.
Locking mechanism locks the drawer when pulled out, pushed in, or folded down.
Full 105 key, low-profile, sturdy keyboard included.
Ultra sturdy, tilt-free, two-piece Rear Bracket and Extension design.
Quick and easy installation.
A universal C-36 connector for connection between console drawer and KVM switch module.
Supports Sun keyboard mapping and Mac keyboard mapping.
Optional Built-in -48V/-24V Power Module available.
OSD Control and Adjustment
Extra Features for Transa PRO 17 and Transa PRO 15
User-replaceable keyboard with various languages support.
User-replaceable touch pad for easy replacement.
Touch pad with simulated wheel control.

Transa PRO
‧
TransaView Console
4
Packing List
Console: "LCD panel + keyboard + mouse pad" console
drawer
Rear bracket & extension kit: This kit contains two pieces of rear brackets and two pieces of extensions.
Make sure you have the correct kit to fit the depth of your cabinet. Note:the following length is
measured between "front pole and rear pole inside a rack cabinet" not the outside depth of a rack
cabinet enclosure.
REK5X REK6X REK7X REK8X REK9X
Front pole to rear
pole distance
( Depth ) cm inch cm inch cm inch cm inch cm inch
Minimum 49.5 191/257.5 225/867.5 265/877.5 301/287.5 341/2
Maximum 57 223/870.5 273/480.5 315/890.5 355/8100.5 391/2
Top view of a rack cabinet with console installed: Depth decides the model number of the REKxX.
REK9X (upper-left)
and
REK5X (lower-right)

Transa PRO
‧
TransaView Console
5
The KVM Switch Module (Please also see another user’s manual for more details about the KVM
Switch module): KVM switch module box can be connected to a console or be used as a stand-alone
KVM switch. There are three major categories: PS/2, USB and Sun interfaces.
PS/2 Interface IKM001 IKM108D IKM116D IKM2108D IKM2116D
No. of console port 1 1 1 2 2
No. of computer port 1 8 16 8 16
KVM switch inside No Yes Yes Yes Yes
OSD menu No Yes Yes Yes Yes
Height 1U 1U 2U 1U 2U
Cable type CBMxxxTor CBKxxxT
Model Indicator 1►1 1►8 1►16 2►8 2►16
Type Hybrid Sun
Model name IGM108D IGM116D ISM108 ISM2208
Interface PS/2, USB Sun (mini-DIN8)
No. of console
port 1 1 1 2
No. of computer
port 8 16 8 8
OSD menu Yes No
Height 1U 2U 1U
Cable type CBMxxxT, CBKxxxT,
CBMxxxUT CBKxxxST
Model Indicator 1►8 for
USB+PS/2
1►16 for
USB+PS/2
1►8 for
Sun
2►8 for
Sun
Type Slim
Model name IMM104D IMM108D IMM116D IUM104D IUM108D IUM116D
Interface PS/2 PS/2, USB
For computer PS/2-PC PS/2-PC, USB-PC,
USB-Sun, USB-Mac
No. of console
port 1 1 1 1 1 1
No. of computer
port 4 8 16 4 8 16
OSD menu Yes Yes
Height 1U 1U
Cable type CBMxxxHCBMxxxH,CBMxxxUH
Model Indicator 1►41►81►16 1►41►81►16
Color of computer
port connector Blue gray Gray
Optional Built-in -48V/-24V Power Modules are available: IKMP001, IMMP104D,
IMMP108D,IUMP104D, and IUMP108D
Bolt-and-nut set
User's manual

Transa PRO
‧
TransaView Console
6
Assembly
1. Choose a proper position for the rack drawer.
Mount the rear brackets (from the Rear bracket &
extension kit), and lightly fasten them onto the rear
vertical poles. Both will be removed later.
2. Remove the safety stopper from the console drawer.
The safety stopper is designed to prevent the drawer
from sliding out during transportation.
★
WARNING
★
After the safety stopper is removed, the drawer may slide out
when tilted and cause serious injury.
3. Slide the console drawer to the rack cabinet from the
front and insert the two slide rails of the console
drawer into the pockets of the rear brackets.
4. Fasten the console drawer onto the front brackets by
four screws. The metal brackets as shown in the
far arrow support rear side of the console.

Transa PRO
‧
TransaView Console
7
5. Remove both of the rear brackets and slide the
console drawer out half way to balance its weight.
Now, the front brackets hold the console drawer.
6. Attach the extensions (from the Rear bracket & extension kit) to both sides of the KVM switch module.
Please note the length of the extensions and mount them in one of the following ways. For a 2U
module, the extensions are mounted to the lower half of the module.
Short extensions attachment Long extensions attachment
7. The rear brackets, extensions and slide rails have tightly fit. Make sure you follow these steps
for easy installation. A. Slide the rear brackets onto the extensions. B. Then, insert both sliding rails
of the console drawer into the tight space formed by the rear brackets and the extensions. The KVM
switch module should be pushed in EVENLY on both of right and left sides by both of your two
hands.
The wider side of plastic
extension is on the upper.

Transa PRO
‧
TransaView Console
8
8. Push the rear brackets all the way in and fastens
them.
9. Slide the console drawer out. Push the KVM switch
module evenly toward the drawer and lock both
units by the screws.
10. Make sure the C-36 connectors are firmly mated
during step 9.
11. Connect the power supply to the power jack on the KVM switch module to complete the installation.

Transa PRO
‧
TransaView Console
9
Installation
The installations for KVM switch module with computers can be found in the other user’s manual.
The combination of a console and an IKM001 can be considered as a set of PS/2 keyboard, mouse and
monitor as shown below.
The console connects to a computer
Or, the console with the 11KVM switch module can be connected to a KVM switch as shown below.
The console connects to a KVM switch

Transa PRO
‧
TransaView Console
10
Front Panel
Front panel of the TransView model
Front panel of the Transa PRO 17/ Transa PRO 15 model
KVM Control and Status: (This section is effective only when a KVM switch module is connected, not
applicable for IKM001 module.)
1. Computer Selection Pad
Press one of these pushbuttons to select a computer. For 16-port models: “1”~”8” represent the lower
8 ports and “A”~”H” for the higher 8 ports. Port “1” and “A” share the same pushbutton, if port “1” is
already selected, tap its pushbuttons to select port “A”. If port “1” is not selected, press and hold the
pushbutton “1” for 2 seconds to select port “A”.
2. Selected Computer Indicator
One of the indicators turns red when it corresponding computer is selected.
3. Local Console in operation
It turns green when a computer is accessed through the console.
4. Remote Console in operation
It turns green when a computer is accessed by another set of keyboard/mouse/monitor
connected to the "Remote" console when the KVM switch module is IKM2108D, IKM2116D,
or ISM2208.
LCD Panel Control
5. LCD Panel Menu
These buttons invoke the OSD menu for settings of the LCD panel as an ordinary LCD
monitor.
6. LCD Panel Adjustment
This can let you adjust settings for the LCD panel.

Transa PRO
‧
TransaView Console
11
Keyboard Status & LCD Panel Power Switch
7. Num Lock
Keyboard Num Lock status.
8. Caps Lock
Keyboard Caps Lock status.
9. Scroll Lock
Keyboard Scroll Lock status.
10. LCD Panel Power Switch
Replaceable Keyboard and Touch Pad (For Transa PRO 17 and Transa PRO 15 ONLY)
Replaceable Keyboard
The keyboard is replaceable for language change or maintenance. Tilt it up, locate the mini-USB cable
underneath the keyboard and gently unplug it. While installing a keyboard, make sure that you extend just
enough of the cable to keep the keyboard flat inside the tray.
Note: The triangular mark on the mini-USB connector must face outwards.
Triangular mark

Transa PRO
‧
TransaView Console
12
Replaceable Touch Pad
1. Touch Pad and Its “Wheel”
The Touch Pad simulates a “wheel mouse”. The area of the Touch Pad to the right side of the two small
triangular marks is the simulated “wheel” as shown below.
2. Touch Pad Replacement
To remove the Touch Pad, press the tab underneath it upward to release the latch, and then slide it outwards
till the Touch Pad can be lifted up clear from the notches, as shown in the figure on the right. The Touch
Pad is attached by a piece of mini-USB cable. To install the Touch Pad, extend just enough mini-USB cable
and slide the Touch Pad all the way in till you hear a click sound as it is locked in position.
Note: The triangular mark on the mini-USB connector must face outwards.
Optional Power Supply Holder
You may secure the power supply on the holder by tie wraps before installing the complete setup to a rack.
Triangular mark

Transa PRO
‧
TransaView Console
13
LCD Panel Specification
Specifications 15” LCD Panel 17” LCD Panel
Active Display Area 304.1 x 228.1 (mm) 337.920 x 270.336 (mm)
Pixel Pitch (mm) 0.297 (H) x 0.297 (V) 0.264 (per one triad) x 0.264
Resolution 1024 x 768 @60/70/75Hz 1280 x 1024
Color Pixel Arrangement RGB vertical strip R.G.B. Vertical Stripe
Display Mode normally white TN Normally White
Brightness(cd/m^2) 250(cd/m2)@8mA 260 (center) @ 7mA
Contrast Ratio 350:1 450:1 (Typ)
Display Color 16.7M (8 bits) 262K colors (RGB 6-bits data)
User Control OSD Control (auto saving) OSD Control
Input Signal RGB analog, H/V separate Even/Odd R/G/B data,
ey sync signal, Clock
Plug-n-Play VESA VESA DDC 1/2B VESA DDC 1/2B
Power Consumption 33W typical, normal operation 25W typical,
(w/o Inverter, All black pattern)
Viewing Angle
-60~60(H)
-55~45(V) (Typ.)
-80~80(H)
-80~80(V) (Typ.)
Backlight Unit 2 CCFLs
edge-light(top/bottom)
4 CCFLs
edge-light(top/bottom)
Temperature
Operating
Storage (Shipping)
0 to +50 (˚C)
-20 to +60 (˚C)
0 to +50 (˚C)
-20 to +60 (˚C)
Operating Humidity Relative Humidity ≦95%
(Ta ≦40˚C)
Relative Humidity 8% ~ 95%
Non-Operating Humidity 90% RH 95% RH
Power Supply Input
Voltage
Full range, 100V AC to 240V AC
Power Supply Input
Frequency 47 Hz ~ 63 Hz
Approval CE, FCC for the product. UL, TUV, CE for power supply
Note:
1) For optimum video performance, VGA resolution should be set to 1024 x 768 for 15” LCD panel and be
set to 1280 x 1024 for 17” LCD panel with low refresh rate.
2) If part of the display is not clear, please activate “Auto Adjust” for the LCD monitor using the four “LCD
Panel Control” buttons.

Limited Warranty
IN NO EVENT SHALL THE DIRECT VENDOR'S LIABILITY FOR DIRECT OR INDIRECT, SPECIAL, INCIDENTIAL OR CONSEQUENTIAL
DAMAGES, LOSS OF PROFIT, LOSS OF BUSINESS, OR FINANCIAL LOSS WHICH MAY BE CAUSED BY THE USE OF THE PRODUCT
EXCEEDS THE PRICE PAID FOR THE PDOCUDT.
The direct vendor makes no warranty or representation, expressed or implied with respect to the contents or use of this documentation, and
especially disclaims its quality, performance, merchantability, or fitness for any particular purpose.
The direct vendor also reserves the right to revise or update the product or documentation without obligation to notify any user of such revisions
or updates. For further information, please contact your direct vendor.
All the brand names and registered trademarks are the property of their respective owners.
PP5-HS000-001
This manual suits for next models
2
Table of contents
Popular LCD Drawer manuals by other brands

ATEN
ATEN CL1000N user manual

Raloy
Raloy RF117HDM user manual

newell
newell Rubbermaid FASTTRACK CLOSET 1086063 manual

Black Box
Black Box KVT217A manual

Bosch
Bosch BIE7101B1 User manual and installation instructions

Rose electronics
Rose electronics Rackview LCD Panel Mount 19" Installation and operation manual

Austin Hughes
Austin Hughes CyberView K1417 user manual

LevelOne
LevelOne KVM-0115 user manual

Digitus
Digitus DS-72102GE user manual

ATEN
ATEN CN8000A quick start guide

Synergy Global Technology
Synergy Global Technology LCD2U17-07 user manual

Crystal Image Technologies
Crystal Image Technologies KVM-2404QSS user manual