ConnectGear XG2 User manual

LED:
Adjust the SCAN TIME:
INSTALLATION:
OPERATION:
To activate the scan mode(Auto status):
To deactivate the scan mode (Manual status):
To select PC:
Transmission Distance
SPECIFICATION
XG2
2 PCs to 1 User
PLASTIC CASE
Yes
16ft (5m)
10ft (3m)
Built-in with 4ft (1.2m) Coaxial cable
43-120Hz
1600 x 1200
200MHz
30-100KHz
1.First turn on the monitor followed by the PCs.
2.Make sure each PC is boot-up completely before 
switching the KVM Switch.
*Hot Key operation : Scroll
Lock
Scroll
Lock
Scroll
Lock
Scroll
Lock
*Press on the keyboard.
ESC
*Hot Key operation: Scroll
Lock
Scroll
Lock
ESC
After the computers are turned on, the front panel shows:
PC1/PC2 LED : The LED will be lit for the PC
which is selected or scanned.
AUTO LED : Lit when in Auto Scan mode.
1. 5 sec Default setting .
2. Press into the Auto Scan mode.
3. Press or to choose the scan rate.
+
SCAN RATE
5 sec.
10 sec.
15 sec.
20 sec.
25 sec.
30 sec.
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
ON
ON
ON
OFF
ON
OFF
ON
OFF
Num Lock
LED
Caps Lock
LED
Scroll Lock
LED
SPECIFICATIONS:
*Note:If the power was turned off,tfe scan rate will
back to the default setting-5 seconds.
XG2
USER'S MANUAL
Please read this manual thoroughly and follow the
instruction procedures to prevent any damage to the
CPU SWITCH and or the connecting devices.
Limited Warranty:
Preventing Radio & TV Interference:
Trouble Shooting:
I N NO EVENT THE DIRECT VENDOR'S LIABILITY EXCEED THE PRICE
PAID FOR THE PRODUCT FROM DIRECT, INDIRECT, SPECIAL,
INCIDENTAL,OR CONSEQUENTIAL DAMAGES RESULTING FROM
THE USE OF THE PRODUCT, DIST, OR ITS DOCUMENTATION.
The direct vendor makes no warranty or representation, expressed,
implied, or statutory with respect to the contents or use of this
documentation, and specially disclaims its quality, performance,
merchantability, or fitness for any particular purpose. The direct
vendor also reserves the right to revise or update device or
documentation without obligation to update. For further inquires
please contact your direct vendor.
WARNING!!! This equipment generates, uses, and can
radiate radio frequency energy and if not installed and used
in accordance with the instructions MANUAL, may cause
interference to radio communications. It has been tested
and found to comply with the limits for a Class A computing
device pursuant to Subpart J of part 15 of FCC Rules, which
are designed to provide reasonable protection against such
interference when operated in a commercial environment.
Operations of this equipment in a residential area is likely to
cause interference in which case the user at his own expense
will be required to take whatever measures may be required
to correct the interference.
•Possible reasons for not compatible with 
XG2 2-Port Mini KVM Switch
1.The BIOS in the mother board.(Basic Input/Ouput
System).
2.The hardware equipment.(Keyboard.Mouse)
3.Software.OS(Operating System)
SITUATION SOLUTION
Mouse Hanged
Keyboard Hanged
Improper Operation
•Check whether the correct mouse 
driver was installed. 
•Change to other mouse.
(PS/2 mouse only for user side)
•Connect the mouse to PC directly.
•Change to the PC port.
•Try to select other port and then
switch back.
•Change to other keyboard.
•Connect the keyboard to PC directly.
•Change to the PC port.
•Try to select other port and then
switch back.
•Do not move keyboard, mouse or
select PC if the initial turn-on
operation procedure is not completed.
•Reboot after the PC is turned off for
5 seconds later.
•Try to select other port and then
switch back.
2 PORT AUTO MINI KVM 
with Built-in cables
2 PORT AUTO MINI KVM 
with Built-in cables
2 PORT AUTO MINI KVM 
with Built-in cables