Connects2 Aerpro APVPO11 User manual

APVPO11
Rear View Camera Input and Video-In-Motion
www.connects2.com

www.connects2.com
www.aerpro.com
2
ABOUT THIS PRODUCT...
APVPO11
Rear-View Camera Input and Video-In-Motion for Porsche Vehicles with PCM 3
and PCM 3.1 Navigation Systems. Add On Reverse Camera Interface for OEM
Systems allows the addition of an aftermarket reverse camera to the OEM screen.
Only for vehicles without factory rear-view camera.
Internal DVD video cannot be watched whilst in motion.
Prior to installation
Read the manual prior to installation. Technical knowledge is necessary for installa-
tion. The place of installation must be free of moisture and away from heat sources.
Please ensure you use the correct tools to avoid damage to the vehicle or product.
Aerpro can not be held responsible for the installation of this product.
Technical Support
Aerpro want to provide a fast and suitable resolution should you encounter any
technical issues. With this in mind, when contacting Aerpro, try to provide as much
Information as possible. This will speed up the process and help us to help you.
Please use our dedicated online technical support centre: intranet.tdj.com.au/
support

www.aerpro.com
www.connects2.com
3
FITTING GUIDE/PIN-ASSIGNMENTS
Setting the Dip Switches of the Interface
Vehicle/ navigation Dip 1 Dip 2 Dip 3 Dip 4 Dip 5 Dip 6
PCM 3 with
video-in-motion activated ON ON OFF OFF OFF OFF
PCM 3 with video-in-motion
deactivated OFF ON OFF OFF OFF OFF
PCM 3.1 with video-in-motion
activated ON ON OFF OFF OFF ON
PCM 3.1 with video-in-motion
deactivated OFF ON OFF OFF OFF ON
Interface Dipswitch Functions:
Dip 1 – Activation of Video in Motion
Dip 2 – Existing Rear View Camera
Dip 3 – Coding rear-view camera by white cable
Dip 4 – Coding Park Assistant by white cable (only PCM3.1, PCM3 no function)
Dip 5 – No function
Dip 6 – No function / CAN-bus termination
Pin-Assignments
Factory Connector - Pin Conguration
Cable Colour Assignment Pin No.
Red +12V Battery Pin 15
Black Ground Pin 12
Orange/Brown CAN-low Pin 9
Orange/Purple CAN-high Pin 11

www.connects2.com
www.aerpro.com
4
PIN-ASSIGNMENTS/CONNECTION SCHEMA
Pin-Assignment of the Interface (Molex 8pin)
Cable Colour Pin-No. Assignment
Yellow Pin 4 CAN-HIGH – connection to the head-unit
Blue Pin 3 CAN-LOW – connection to the head-unit
Yellow/Black Pin 8 CAN-HIGH – connection to the vehicle
Blue/Black Pin 7 CAN-LOW – connection to the vehicle
Red Pin 1 +12V Permanent
Black Pin 5 Ground
Green Pin 2 +12V rear-view camera (max. 400mA)
White Pin 6 Alternative coding
Connection Diagram
Interface

www.aerpro.com
www.connects2.com
5
INSTALLATION
NB: Before installation, switch off ignition, disconnect the vehicle battery and re-
move the vehicle’s head unit.
The interface is installed behind the vehicle’s head unit.
Conneting Interface, Harness and Factory Navigation Monitor
1. Connect the female 8pin Molex connector of the harness to the male 8pin
Molex connector of the Interface.
2. Transfer the female Quadlock connector of the vehicle harness from the rear of
the head-unit into the male Quadlock connector of harness.
3. Plug the female Quadlock connector of the harness into the male Quadlock
connector on the rear of the head-unit.
Interface

www.connects2.com
www.aerpro.com
6
INSTALLATION
Connections to Rear-View Camera
1. Connect the video RCA of the rear-view camera to the female RCA
connector of harness.
2. Connect the green cable of the harness to the camera power supply (+12V
max 400mA). The green cable is high when reverse gear is engaged
(and if ignition is off). The power will be deactivated from a speed of 20 km/h.
Coding of the Rear-View Camera (Only PCM3.1)
BACK
HANG UP
HASH KEY/MODE
ACCEPT
Steering-Wheel Buttons Left Steering-Wheel Buttons Right

www.aerpro.com
www.connects2.com
7
It is necessary to code the rear-view camera input of the PCM 3.1 for use of an
aftermarket camera
1. Turn on ignition
2. Wait until the head-unit has booted up
3. Press and hold steering-wheel button HASH KEY/MODE
4. Press and hold steering-wheel button ACCEPT
5. Hold both buttons. During
congurationtheredandblueLED
willashinsidethe
CAN-box (visible at the male 8pin
Molex connector). The PCM will
reset after 5-10 seconds
6. Disengage both steering-wheel
buttons.
7. When coding is successful, the red
and the blue LED inside the CAN-Box
will be lit and the notice, “Rear-view
camera“, will appear in the menu.
Optionally coding of ParkAssistant to retrot factory PDC (only PCM3.1)
BACK
HANG UP
HASH KEY/MODE
ACCEPT
Steering-Wheel Buttons Left Steering-Wheel Buttons Right
INSTALLATION

www.connects2.com
www.aerpro.com
8
INSTALLATION
ItisnecessarytocodetheParkAssistantofthePCM3.1toretrotfactoryPDC.
1. Turn on ignition
2. Wait until the head-unit has booted up
3. Press and hold ‘Back’ on the steering wheel
4. Press and hold ‘Accept’ on the steering wheel
5. Holdbothbuttons.DuringcongurationtheredandblueLEDwillash
inside the CAN-box (visible at the male 8pin Molex connector).
The PCM will reset after 5-10 seconds
6. Disengage both steering-wheel buttons
7. When coding is successful, the red and the blue LED inside the CAN-
Box will light up and the notice ”Park Assistant“ will appear in the menu
Decoding of the Park Assistant (only PCM3.1)
It is possible to decode the Park Assistant as follows:
1. Turn on ignition
2. Wait until the head-unit has booted up
3. Press and hold ‘Back’ on the steering wheel
4. Press and hold ‘Hang Up’ on the steering wheel
5. Holdbothbuttons.DuringcongurationtheredandblueLEDwillash
inside the CAN-box (visible at the male 8pin Molex connector).
The PCM will reset after 5-10 seconds
6. Disengage both steering-wheel buttons
7. When decoding is successful, the red and the blue LED inside the CAN-
Box will light up and the notice “ParkAssistant“ disappears in the menu

www.aerpro.com
www.connects2.com
9
INSTALLATION
Alternatively coding and decoding of rear-view camera and ParkAssistant
(e.g. if steering-wheel buttons not existing, only PCM3.1)
Alternatively to coding through the steering-wheel buttons, the coding and
decoding of rear-view camera and Park Assistant can be completed via the
loose white cable in connection with Dip 3 and 4 on the Interface.
Dip Function ON OFF
Dip 3 Rear-view camera Coding Decoding
Dip 4 ParkAssistant Coding Decoding
1. Turn on ignition
2. Wait until the head-unit has booted up
3. Set Dip3 and Dip4 of Interface (depending on the desired coding/
decoding)
4. Put +12V for 5 sec. to the white cable
5. DuringcongurationtheredandblueLEDwillash
inside the CAN-box (visible at the male 8pin Molex connector).
The PCM will reset after 5-10 seconds
6. The red and the blue LED inside the Interface will light up and the
notice “Rear-view camera“ or “ParkAssistant” will appear in the
menu after successful coding (or disappear after successful
decoding)
If a factory PDC exists in the car, set Dip4 to “ON” while coding, otherwise the
factory PDC will be decoded

www.connects2.com
www.aerpro.com
10
INSTALLATION/SPECIFICATIONS
Coding and decoding of rear-view camera (Porsche Cayenne Only)
The rear-view camera can be coded or decoded via the loose white cable in
connection with Dip3 of the Interface.
Dip Function ON OFF
Dip 3 Rear-view camera Coding Decoding
1. Turn on ignition
2. Wait until the head-unit has booted up
3. Set Dip3 and Dip4 of Interface (depending on the desired coding/
decoding)
4. Put +12V for 5 sec. to the white cable
5. DuringcongurationtheredandblueLEDwillash
inside the CAN-box (visible at the male 8pin Molex connector).
The PCM will reset after 5-10 seconds
6. The red and the blue LED inside the Interface will light up and the
notice “Rear-view camera“ or “ParkAssistant” will appear in the
menu after successful coding (or disappear after successful
decoding)
Activation of Video-In-Motion Functionality
With Dip1 set to “ON”, the video-in-motion function is activated permanently