Consort LTR07N Product guide

Specifications
DIMENSIONS
Model
LTR07N
Height:
795 mm
Width:
530 mm
Depth:
120 mm
Weight:
5.5 kg
ELECTRICAL
Wattage:
60-65 W
Supply: 230-240 Volts ac 50 Hz, single phase
Ingress Protection Rating: IP34 –Splashproof –Double Insulated
Consort reserve the right to alter specifications without notice.
Guarantee
This guarantee is offered to you as an extra benefit and does not affect your legal rights.
All electrical appliances produced for the Company are guaranteed for one year against
faulty material or workmanship. This applies only if the appliance has been used for purposes
in accordance with the instructions provided and has not been connected to an unsuitable
electricity supply, or subject to misuse, neglect, damage or modified or repaired by any
person not authorised by us.
The correct electricity supply voltage is shown on the rating label attached to the appliance.
CUSTOMER HELPLINE
Should you need any advice on the use of your new
Consort product, or should you require service or repair,
please contact our Helpline:
Operating hours: Mon to Thu 8.30am to 4.30pm | Fri 8.30am to 3.30pm
Consort Equipment Products Limited
Thornton Industrial Estate, Milford Haven
Pembrokeshire, SA73 2RT
Tel: [phone] Fax: [phone]
Email: [email protected] Web: www.consortepl.com
46000129 Iss 03
Operating & Installation Instructions
Heated Ladder Towel Rail
LTR07N
Please retain this leaflet for future reference

Installation
The supply circuit must be adequate for the input of the appliance and the towel rail must
be connected via a fused, double pole, switched, (having a contact separation of at least
3 mm in each pole), flexible cable outlet and fitted with a 3 Amp fuse or via a plug and socket.
The towel rail must be connected in accordance with the latest IEE Regulations and fitted by a
competent electrician.
IMPORTANT: When installed in a bathroom, the unit must not be connected via a plug and
socket. The towel rail must also be located in the appropriate zone of the bathroom, in
accordance with section 601 of the Wiring Regulations BS 7671:1992 (Amendment 10983).
NOTE: This class II appliance does NOT require Earthing. The side frames of the Heated
Towel Rail should be mounted vertically with the curved rungs horizontal. The Heated Towel
Rail should be positioned at least 300mm above floor level, with flex entry at bottom.
To attach the Towel Rail to the wall
1. Firstly establish a suitable position on the wall for attaching the Towel Rail, preferably
with at least two leg Mounting Bases aligned with wall studs or dwangs. Mark the
location of ONE of the Mounting Bases on the wall.
2. Drill a hole centrally at the marked location and fix Mounting Base to the wall, either with
a wall fixing screw (supplied) or a suitable wall fixing plug.
3. Attach the adhesive tape (supplied) to the back of remaining three Mounting Bases, and
remove the protective paper backing.
4. Insert remaining three Mounting Bases into
the frame legs. Ensure the rectangular fixing
slot, in each Mounting Base, faces
downwards so as to correctly align with the
fixing hole in each frame leg.
5. Position the corresponding Towel Rail frame
leg onto the Mounting Base already
screwed to the wall. If necessary use a
level to align the Towel Rail in the desired
position, before pressing firmly against the
frame. Ensure the remaining three Mounting
Bases adhere to the wall.
6. Pull the frame away, leaving the Mounting
Bases attached to the wall.
7. Drill and fasten the remaining three
Mounting Bases to the wall, either with the
fixing screws supplied or with suitable wall
fixing plugs.
8. Refit Heated Towel Rail frame over the
Mounting Bases, and lock in place with the
four leg fixing screws (supplied) through the
underside of each leg.
9. Either connect the Mains Flex provided, to a
suitable three pin plug, or if installed in a
bathroom, have an authorised person
connect it to a switched permanent
connection unit.
Operation
Your Consort Heated Ladder Towel Rail costs approximately the same to run as a
100 Watt light bulb. It will take approximately ¾ hour to reach operating temperature and, if
need be, can be left running continuously.
Care
The Heated Towel Rail is best wiped down from time to time with a damp cloth. Do not
use any abrasive or corrosive cleaners.
Safety Information
When using any electrical appliance, basic safety precautions should always be
observed. Read these instructions carefully, and retain for future reference:
NOTE: The appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
This appliance is intended to dry towels and therefore is hot to the touch. When used by
or near young children or infirm persons, close supervision is necessary. Young children
should be supervised to ensure that they do not play with the appliance.
Any rise in ambient temperature is directly reflected in the appliance, and as a result of
this the appliance will feel hotter to the touch during warmer periods. Also the insulation
effect of towels will cause the operating temperature to increase slightly.
Do NOT use this appliance other than for its intended use.
To avoid a hazard this heated towel rail MUST NOT be used to carry towels or any other
articles that have been in contact with oil, petroleum based products or dry cleaning
fluids.
Use this appliance only on the voltage specified on the rating label.
Regulations require that electrical work be carried out only by authorised persons. For
your own safety and that of others, ensure this is done.
Do NOT immerse in any liquid.
Do NOT allow the supply cord to come into contact with heated surfaces during
operation.
Special purpose tools are required for replacement of the power supply cord and
element. For service, contact your nearest Authorised Service Agent.
CAUTION: If this appliance is supplied from a cord extension set or an electrical portable
outlet device, the cord extension set or electrical portable device must be positioned so that it
is not subject to splashing or ingress of moisture.
If your towel rail does not work
Check that the fuse has not blown at the flex outlet, in the plug or at the distribution board.
Do NOT attempt to repair the towel rail.
Should none of the above remedies work then consult an accredited service agent. If the
appliance is still under guarantee, return it to your supplier.
46000129 Iss 03