Contemporary Controls BASstat BAST-421C-BW2 User manual

BAST-421C-BW2
Wireless BACnet Communicating Thermostat for Modulating Fan Coil Operation
BASstat
Wireless Modulating Thermostat
User Manual
#UM-15093500-AA1

UM-15093500-AA1
Page 1
Trademarks
BASautomation, Contemporary Controls, and CTRLink are registered trademarks of
Contemporary Control Systems, Inc. BACnet is a registered trademark of the American Society
of Heating, Refrigerating and Air-Conditioning Engineers, Inc. Powered by Sedona Framework
is a trademark of Tridium, Inc. Other product names may be trademarks or registered
trademarks of their respective companies.
Copyright
© Copyright 2021, by Contemporary Control Systems, Inc. All rights reserved. No part of this
publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or
translated into any language or computer language, in any form or by any means, electronic,
mechanical, magnetic, optical, chemical, manual, or otherwise, without the prior written
permission of:
Contemporary Control Systems, Inc.
Tel:
[phone]
2431 Curtiss Street
Fax:
[phone]
Downers Grove, Illinois 60515 USA
E-mail:
[email protected]
Disclaimer
Contemporary Control Systems, Inc. reserves the right to make changes in the specifications
of the product described within this manual at any time without notice and without obligation of
Contemporary Control Systems, Inc. to notify any person of such revision or change.

UM-15093500-AA1
Page 2
Contents
1Introduction................................................................................................................ 3
1.1 Features and Benefits.......................................................................................... 4
1.2 Product Image and Main Features....................................................................... 5
2Specifications ............................................................................................................ 6
2.1 Inputs................................................................................................................... 6
2.2 Outputs ................................................................................................................ 6
2.3 Communication.................................................................................................... 6
2.4 Electrical .............................................................................................................. 6
2.5 Environmental...................................................................................................... 7
2.6 Electromagnetic Compatibility.............................................................................. 7
2.7 Mechanical (all dimensions are in mm)................................................................ 8
3Installation ................................................................................................................. 9
3.1 Terminal Block Pin Assignments ......................................................................... 9
3.2 Limited Power Source.......................................................................................... 9
3.3 Power Supply Precautions................................................................................. 10
3.4 Wiring Diagram .................................................................................................. 10
4Operation................................................................................................................. 11
4.1 User Mode ......................................................................................................... 11
4.2 Control Type ...................................................................................................... 13
4.3 Engineering Mode Menu.................................................................................... 16
4.4 BACnet Objects and Network Configuration ...................................................... 22
5Warranty .................................................................................................................. 35
6Returning Products for Repair ................................................................................. 35
7Declaration of Conformity ........................................................................................ 36

UM-15093500-AA1
Page 3
1 Introduction
The BAST-421C-BW2 is a member of the BASstat BACnet Communicating Thermostat series.
It provides modulated heating and cooling control in an attractive wall-mounted enclosure with a
large LCD display. Intended for use with 4-pipe heated/chilled water Fan Coil units, the
thermostat can control 2 analog modulating water valve actuators and one binary supply fan.
This BASstat is BACnet compliant and BTL listed to ensure seamless integration, using
BACnet/IP over Wi-Fi and can be integrated into any 802.11 b/g/n Wi-Fi network. A large, easy
to read LCD display indicates setpoint, space temperature and current mode of operation using
graphical icons.
The BASstat has a built-in space temperature sensor with provision for remote wired 3kΩ NTC
thermistor sensor or temperature value can be sent by another communicating device over the
BACnet network. The BASstat is configurable locally using the Engineering Menu or via a
network connection to a BACnet client. Contemporary Controls’ free BACnet Discovery Tool
can be used for initial configuration of the thermostat over BACnet. Control algorithm
parameters such as deadband, proportional gain, integral rate and trip points are all
configurable. This BASstat also features configurable fan control and occupancy selection.
Operating states are indicated on the thermostat display.
The numerous features available in the BASstat can be configured by the systems integrator to
meet user requirements in two different ways. One way is using a button sequence on the
thermostat in order to enter the Engineering Menu - which requires physical access to the
thermostat. Optionally, the buttons could be locked to limit user access to Engineering Menu
after installation is complete. The second method is configuring the thermostat over the BACnet
network using a BACnet client device or software such as Contemporary Controls’ free BACnet
Discovery Tool (BDT).
NOTE: 2-pipe HVAC systems and floating-type control valve actuators are not supported by this
device.

UM-15093500-AA1
Page 4
1.1 Features and Benefits
• Stand-alone thermostat algorithm or fully BACnet network-controllable
• B-ASC device profile for integration into BACnet networks
• 24VAC (+/-10%) power input
• BACnet communication -BACnet/IP over Wi-Fi and can be integrated into any 802.11
b/g/n Wi-Fi network
• Suitable for 4-pipe modulating heat/cool control applications with manual or automatic
changeover NOTE: 2-pipe heat/cool applications and floating-type valve actuator are not
supported by this device
• Adjustable algorithm applied to modulating valve control
• Effective run time accumulation for energy consumption metering
• Configurable control parameters such as deadband, proportional gain, integral rate and
cycle time
• Adjustable minimum/maximum set point ranges
• Three options for temperature reading:
oBuilt-in temperature sensor, or
oRemote sensor (RS) input for wiring in a remote temperature sensor (NTC 3kΩ), or
oBACnet network temperature override
• Occupancy status can be switched (1) locally by the user, (2) by using a separate
occupancy sensor, or (3) by using BACnet network command
• Separate adjustable occupied and unoccupied set points for heating and cooling mode
• Fan can be set to run continuously or automatically
• Non-volatile memory retains user settings during power outage
• Thermostat buttons are lockable to prevent tampering
• °C or °F display
• Energy Savings Input for local occupancy control
• Control outputs disabled during “OFF” state for safety

UM-15093500-AA1
Page 5
1.2 Product Image and Main Features
BASstat 421C-B2 and BASstat 421C-BW2

UM-15093500-AA1
Page 6
2 Specifications
2.1 Inputs
Item
Description
Temperature Display Range
-22 to 248°F (-30 to 120.0°C) with suitable sensor
Temperature Display Resolution
0.1°F (0.1°C)
Temperature Accuracy
±1.8°F (±1.0°C) with all outputs off
Energy Savings Input
Provision for external occupancy sensor
Setpoint Range
32-122°F (0-50°C) in 0.5° (°F or °C) increments
Remote Temperature Sensor
Provision for NTC Type 3kΩ thermistor
2.2 Outputs
Item
Description
Relay Output
Fan
Analog Outputs
0-10v modulating AO1 (cooling), AO2 (heating)
Contact Rating
SPST 2A at 30 VAC with inductive load
Minimum contact life
100,000 cycles
2.3 Communication
Item
Description
Protocol Compliance
BACnet/IP with B-ASC, BTL Listed
Physical Layer
802.11 b/g/n Wi-Fi network
Cabling
None
2.4 Electrical
Item
Description
Supply Voltage and Current
24 VAC (±10%) 5 VA
Power Source Class
NFPA 70 (NEC) Article 725 Part III Class 2
Internal Power Supply
Half-wave rectified and filtered DC

UM-15093500-AA1
Page 7
2.5 Environmental
Item
Description
Operating Temperature
32° to 122°F (0 to 50°C)
Storage Temperature
14° to 140°F (-10 to +60°C)
Relative Humidity
5 to 95% non-condensing
2.6 Electromagnetic Compatibility
The BAST-421C-BW2 complies with the following specifications and bears the CE mark in
accordance with the provisions of the Electromagnetic Compatibility (EMC) Directive
2004/108/EC based on the following specifications:
Standard
Test Method
Description
EN 61000-6-2
IEC 61000-4-2
Electrostatic Discharge Immunity
EN 61000-6-2
IEC 61000-4-3
Radiated, Radio-Frequency,
Electromagnetic Field Immunity
EN 61000-6-2
IEC 61000-4-4
Electrical Fast Transit/Burst Immunity
EN 61000-6-2
IEC 61000-4-5
Voltage Surge Immunity
EN 61000-6-2
IEC 61000-4-6
Immunity to Conducted Disturbances
EN 61000-6-2
IEC 61000-4-8
Power Frequency Magnetic Field
Immunity
EN 61000-6-2
IEC 61000-4-11
Voltage Dips and Interruptions
EN 61000-6-3
IEC 61000-3-2
Limits for Harmonic Current Emissions
EN 61000-6-3
IEC 61000-3-3
Limitation of Voltage Fluctuations and
Flicker in Low Voltage Supply Systems

Page 8
UM-15093500-AA1
2.7 Mechanical (all dimensions are in mm)
Mounts directly onto wall, panel, standard 65×65mm junction box (hole pitch 60 mm) or
standard 2×4-inch vertical junction box (hole pitch 83.5mm).
Width: 94mm Height: 118mm Depth: 34mm

Page 9
UM-15093500-AA1
3 Installation
The BASstat 421C-BW2 is intended for surface-mount installation on an interior wall, away from
direct sunlight or direct air movement. The display (top half) can be removed from its base by
loosening the small Philips screw at the bottom of the display. Once the display is removed from
the base, the base can be mounted onto the wall with appropriate fasteners. If a single-gang
electrical junction box is to be used, the top and bottom mounting holes will align with the screw
holes in the junction box.
3.1 Terminal Block Pin Assignments
Two terminal blocks are provided for all field connections. The remote sensor input (RS) is at
terminals 13 and 14. The remote occupancy (ESI) input is a dry contact closure input located at
terminals 14 and 15.
Number
Mark
Comment
Number
Mark
Comment
1
R
24 VAC high-side
10
AO1
Cooling Device
2
C
24 VAC common
11
COM
3
12
AO2
Heating Device
4
13
RS
Remote Sensor Input
5
14
COM
Sensor Common
6
15
ESI
Energy Saving Input
7
16
8
G
Fan
17
9
18
3.2 Limited Power Source
The BASstat is intended to be powered by a Class 2 compliant power source and only accepts
24VAC with no more than 5VA of power consumption. It should be powered by a Class 2 power
source complying with the requirements of the National Electric Code (NEC) article 725. The
transformer or power supply complying with the Class 2 rating must carry a corresponding
listing from a regulatory agency such as Underwriters Laboratories (UL).

Page 10
UM-15093500-AA1
3.3 Power Supply Precautions
Internally, the BASstat utilizes a half-wave rectifier and can share the same AC power source
with other half-wave rectified devices. Sharing AC power with full-wave rectified devices is NOT
recommended. AC power sources that power several half-wave devices have a common
secondary connection called COMMON, LO, or GROUND. Connect the HOT side of the
secondary to the 24 VAC high side input on the BASstat and the LO side to 24 VAC common.
WARNING: Devices powered from a common AC source could be damaged if a mix of half-
wave and full-wave rectified devices are both present. If you are not sure of the type of rectifier
used by another device, do not share the AC source with it.
3.4 Wiring Diagram
Wiring: 14 to 22 AWG wires or 1.5mm2wires.

Page 11
UM-15093500-AA1
4 Operation
4.1 User Mode
User-side control is accomplished with six buttons – MODE (Heat, Cool, or Ventilate), FAN
(Auto or On), UP, DOWN, SET, and POWER. There are also options to lock the panel buttons
to limit user access if so required. A large LCD display indicates setpoint, space temperature,
occupancy status, and current mode of operation using graphical icons.
System modes (Cool, Heat, Ventilate) available to the user are dependent on control type
chosen from Engineering Menu (tyPE) or BACnet object [MSV7] Control Type. See section 4.2
Control Type of this manual).
System modes and button operation may be limited by installation engineer, especially if the
thermostat is completely controlled over BACnet network.
The first tier of operation includes the following settings as shown below. To operate the
thermostat:
1. The POWER button toggles between ON or OFF states to start / stop the
thermostat. This will disable control (ON/OFF control can be accomplished over BACnet as
well).
2. At power ON, press any button to start the User Mode operation. Press the MODE
button
to toggle between different HVAC operating modes such as Cool, Heat, or
Ventilate@Cool and Ventilate@Heat.
Press the UP/ DOWN buttons to adjust temperature setpoint or rotate the
values of a setting. Press the FAN button to toggle fan modes of AUTO or
CONTINUOUS On. If no AUTO icon is displayed, the fan will run continuously until commanded
off using button on thermostat or BACnet command. If AUTO icon is flashing, the fan is
operating under delay timer and will shut off automatically when delay timer expires.
Press the SET button and use UP/ DOWN buttons to toggle the
unit between Occupied or Unoccupied states when outside of scheduled operation. Use SET or
MODE to apply (SET button can be locked in applications forbidding occupancy state user
control).
3. Thermostat will return to normal display with the last known setting if there’s no button
pressed for 10 seconds.

Page 12
UM-15093500-AA1
User Mode Thermostat Operation
#
Item
Description
Remarks
1
Normal Display
Display current room or set-point
temperature
Use the (SP) parameter in the
Engineering Menu or [MSV6]
Display to choose Current room
or Set- point temperature on
display.
2
Temperature
Setpoint Setting
using Up/Down
Arrows
Set the desired temperature
The [AV0] / [AV3] Cool / Heat
Occupied and [
AV8] / [AV9]
Unoccupied
Cool / Heat
temperature setpoints BACnet
objects can be used to write or
force the setpoint to a desired
value from BACnet supervisor.
3
Mode Select
Select the working mode:
Cooling ( ), Heating ( ), or
Ventilating
( ).
After pressing the MODE button,
press the UP/ DOWN button to
rotate the selections. Dependent
on Control Type.
4
Fan Auto/
Continuous
Change the Fan mode between
Auto or Continuous On.
When AUTO is displayed, the
fan is handled automatically.
When AUTO is flashing, the fan
is working under a delay timer.
When FAN icon is spinning but
AUTO is not displayed, the fan
will run continuously until
commanded off.
5
Occupancy Setting
Press SET, Used UP and DOWN
arrows to toggle between the
Occupied and Unoccupied setting.
Use MODE or SET buttons to
apply.
The SET button could be
locked for applications
forbidding user occupancy
state control.

UM-15093500-AA1
Page 13
User Mode Flow Chart
4.2 Control Type
Control Type, System Mode and Algorithm Configuration
System modes available to the user are dependent on control type.
4-Pipe Cooling or Heating with Auto Changeover – This the default control type in this
thermostat. Mostly used for standalone operation. The thermostat will switch between Cool
and Heat modes automatically. In this control type, the user will be presented with a choice
of Heat or Ventilation@Heat when the thermostat is in Heat mode (automatic), and Cool or
Ventilation@Cool when the thermostat is in Cool mode (automatic).
4-Pipe Cooling or Heating with Manual Changeover – In this control type the thermostat will
wait for a command from user or BACnet supervisor to switch between Cool and Heat
modes. The user will be presented with a choice of Heat or Ventilation@Heat when the
thermostat is in Heat mode, and Cool or Ventilation@Cool when the thermostat is in Cool
mode. The user can choose to switch between Cool and Heat modes using the MODE
button.
BACnet controlled – In this control scheme, the built-in thermostat algorithm can be
bypassed, and the thermostat can be controlled over the BACnet network with commands
from the supervisor device. The logic executing in the supervisor (such as Niagara or
Sedona logic) can control the thermostat over the BACnet network. To put the thermostat in

UM-15093500-AA1
Page 14
BACnet network control mode, use the Lock [AV18] object bit 9: Control DOs by thermostat
algorithm “0” (default) or BACnet supervisor “1” (add decimal=512).
Cool Only and Heat Only modes (nullified/disabled in firmware) are control types listed in the
BACnet object and Engineering Menu object but are not available for use.
Control type is only configurable by the installer using Engineering Mode Menu or BACnet
supervisor. The installer must decide the control type suitable for the application, set it to a
static value, or program the BACnet supervisor to change the control type automatically. The
default control type is set to 4-Pipe Cooling or heating with Auto Changeover. Manual
Changeover can be used to prevent excessive automatic changeover between cooling and
heating system modes.
Algorithm
• A PID adaptive control algorithm is applied to minimize overshoot, in addition to
proportional band (Stage Width) and derivative (Differential) calculation.
• When the thermostat is active (either the heating or cooling stage is on), a
“Working ( )” icon will be shown on the LCD.
System Mode
• The default control type, modulating cooling and heating with automatic changeover,
allows the thermostat to operate as fully stand-alone. Manual Changeover allows
restriction of mode selection to Cool only or Heat only where necessary. Control Type
can be selected in (tyPe) or [MSV7].
• For manual changeover control, cooling or heating system modes can be selected by
pressing the MODE button or using a BACnet command to object [MSV1]. In
application where user control needs to be limited, the lock button function can be
used to disable MODE button.
• Occupied Cooling [AV0] and Heating [AV3] set points and Unoccupied Cooling [AV8]
and Heating [AV9] setpoints can be set individually. Minimum deadband [AV7] can be
programmed as well.
Modulating Valve Offset
• The minimum control analog output voltage (low limit) for the modulating valves (AO1
and AO2) is set to 0 volts. These values can be changed at [AV11] for AO1 and
[AV27] for AO2. The setting is measured as an LSB range of 0~125.
Assigned Current Temperature
• A current temperature value can be assigned thru BACnet AV-1 to take place of the
onboard temperature sensor value. The assigned value is valid if BACnet
communication is driving a flip-flop signal to (BV-16: heartbeat signal) within the (AV-
29: Heartbeat Rate time) period (in seconds). Otherwise, the assigned temperature
will revert back to the onboard sensor reading.

UM-15093500-AA1
Page 15
Floating Deadband
• The Heat and Cool temperature setpoints could be “attached” together. This means
that as one setpoint is adjusted and “hits” against the deadband region, it will “push”
the deadband region and the other setpoint along the temperature setpoint axis to
allow for adjustment while maintaining the configured deadband. If the setpoint is
adjusted back the other way, it will “pull” the deadband region and the other setpoint
along the temperature setpoint axis.
Minimum Cooling Setpoint and Maximum Heating Setpoint
• Minimum Cooling Setpoint will be confined by set point low limit plus dead band and
Minimum cooling setpoint [AV-39] Default 18°C/ 65°F
• Maximum Heating Setpoint will be confined by set point high limit minus dead band
and Maximum heating setpoint [AV-40] Default 25°C/ 77°F
Fan Control Output
• Lowest Fan Speed is the speed the fan will default to after a control action (Heating or
Cooling) with fan in AUTO mode. If the lowest fan speed [MSV4] is set as “Stop (1)”,
the fan will automatically shut off after the control action plus a 2-minute fan-off time
delay. During this delay, the AUTO icon will flash. If lowest fan speed is set to “Low (2)”
the fan will run continuously after a control action
• Fan Mode can be toggled between AUTO or ON by using the FAN button on the
thermostat or BACnet object [MSV0] Fan Mode (BACnet supervisor). By default, this
value is set to “Auto(1)”, the AUTO icon is displayed and fan operation will be
controlled automatically. To put the fan in ON mode set [MSV0] to “Low(2)”. This will
cause the fan to run continuously (no AUTO icon is displayed). Fan icon spins when
fan is active. The FAN button can be locked to limit user access to this feature or the
BACnet supervisor can be programmed to default the thermostat to certain state at the
end of an occupancy cycle.
Occupancy Setting

UM-15093500-AA1
Page 16
There are several ways to define thermostat occupancy state. Note: Occupancy will be
detected by ESI contact by default.
1. Energy Savings Input (ESI) This is a dry contact input meant for communication
from a customer supplied occupancy sensor. (default)
2. Occupancy status (occupied/unoccupied) can be set by a BACnet supervisor using
writable object ESI Contact Definition [BV14]. “0” for occupied, and “1” for
unoccupied. E12/AV18 must be set with a value of 64 (disabled) in advance
(E12/AV18 is set as 0 by default)
3. User control of occupancy state is allowed from the SET button if E12/ AV18 Lock
has the ESI Contact disabled. Pressing the SET button and UP/DOWN buttons will
toggle the occupancy state. Press SET button to confirm. The SET button can
work in conjunction with BACnet occupancy Command [BV14] on last-write-wins
basis. The SET button could be locked to limit user control (use Lock [AV18]
BACnet object or (LOC) engineering menu item to lock SET button). In this case
only the BACnet supervisor can set occupancy states.
• Occupancy Status [BI0] is a read-only BACnet object indicating current occupancy
state -“0” for occupied, and “1” for unoccupied. (AV18 is set as 0 by default).
• When in unoccupied state, a Moon ( ) icon will be displayed on the LCD and the
thermostat will change the set-point temperatures to the Unoccupied Cool and
Unoccupied Heat setpoints [AV8 – 9]. When the state changes back to occupied, the
thermostat will return to the occupied set-point values for Cooling and Heating
Temperature Setpoint [AV0, AV3] and a sunlight icon ( ) will be displayed to
indicate occupied state on LCD
4.3 Engineering Mode Menu
Thermostat configuration can be performed using the engineering menu or by controlling
BACnet objects using a BACnet client tool such as Contemporary Controls free BACnet
Discovery Tool (BDT). It is highly suggested that engineering mode be operated by trained
installers only, because it is related to system parameters that will affect the control results.
Operation of Engineering Menu
• At power “ON,” press and hold both the UP and DOWN buttons simultaneously for 5
seconds to enter Engineering Mode menu.
• Press the UP or DOWN buttons to rotate through the menu items. The last item loops
back to first item at the end of items in menu. Press the MODE button to enter a
submenu item.
• Press the UP or DOWN button to change the setting in the submenu item. Press the
MODE button to confirm the setting and return to menu item selection. If no button is
pressed for 10 seconds, the display will return to the menu item selection. After
another 10 seconds, the display will return back to User mode. Settings are not
changed unless confirmed using the MODE button.
• To leave Engineering Mode, rotate till (End) menu item appears and press the MODE
button. Alternately, pressing no buttons for 10 seconds will return the thermostat back

UM-15093500-AA1
Page 17
to User mode.
Engineering Menu Flow Chart

UM-15093500-AA1
Page 18
Engineering Menu Items Table BAST-421C-BW2
Item Mnemonic Description °C Scale °F Scale
Step
Default Range Default Range
E1 db Deadband 2.0 0~10 4.0 0~18 0.5 (°C/°F)
E2 ESIC
Unoccupied(ESI) cooling set point
28 25~35 82.5 77~95 1.0 (°C/°F)
E3 ESIH
Unoccupied(ESI) heating set point
15 10.0~22.0 59 50.0~72.0 1.0 (°C/°F)
E4 I-t
Integral Time and Output Cycle Time
(seconds)
60 0~500 60 0-500 10 (Sec.)
E5 OPL1
Minimum output voltage in digital value for AO1
when reach Low limit
0(0V)
0~125
0(0V)
0~125
1 (LSB)
(0.044V)
E6 SPA1 AO1 Span Offset
-20(10V)
-55~0
-20(10V)
-55~0
1 (LSB)
(0.044V)
E7 SP-L
Low limit for temperature set point
10 0~50 50 32~122 1.0 (°C/°F)
E8 SP-H
High limit for temperature set point
30 0~50 95 32~122 1.0 (°C/°F)
E9 OFSt Current temperature offset 0.0 -10.0~10.0 0.0 -18.0~18.0 0.1 (°C/°F)
E10 Pb Proportional band or stage width 1.5 0~10.0 3.0 0~18.0 0.1 (°C/°F)
E11 diFF Stage differential 0.5 0.1~1.0 1.0 0.1~1.8 0.1 (°C/°F)
E12 LOC
Bit Definition:
0: MODE button (dec=1)
1: Down buttons (dec=2)
2: Up button (dec=4)
3: FAN SPEED button (dec=8)
4: Power On/Off button (dec=16)
5: SET (or ℃/℉) button (dec=32)
6: ESI contact detection (dec=64)
7: Door/Window contact detection
(dec=128)
8: Modification for communication
parameters (dec=256)
i.e. baud rate, MAC addr, device inst.
9: Control DOs by thermostat algorithm
(0) or BACnet sup. (1) (dec=512)
10~15: reserved/unused
Bit Value
0: Unlock / enable
1: Lock / disable
Examples (add dec values to lock multiples)
Unlock/enable all (0)
Lock MODE Button (1)
Lock Down Button (2)
Lock MODE & Down Buttons (3 = 1+2)
Lock Power On/Off button (4)
Lock MODE & Power & Down (7 = 1+2+4)
Lock SET button (32)
Lock MODE & Down & Power & SET (39 =
1+2+4+32)
ESI contact disable (64)
Lock the modification for communication
parameters (
256)
DOs control commanded by BACnet (512)
64
0-1023
64 0-1023 1

UM-15093500-AA1
Page 19
Item Mnemonic Description
°C Scale °F Scale
Step
Default Range Default Range
E13
ESI ESI (DI1) digital sensor contact definition 0 0~1 0 0~1 0: N.O.
1: N.C.
E14
rE-C Modulating Cooling direct/ reverse signal
output
0
0~1
0
0~1
0 (direct)
1 (reverse)
E15
rE-H Modulating Heating direct/ reverse signal
output
0
0~1
0
0~1
0 (direct)
1 (reverse)
E16
rS
Present Temperature is getting from built-in
temperature Sensor, remote temperature
sensor, or assigned through communication
0 0~2 0 0~2
0: built-in
1: remote sense
2: assigned
through
BACnet
E17
-SP-
Display present temperature value of or
current set-point for LCD
0 0~1 0 0~1 0: display PV
1: display SP
E18
door Door or Windows contact definition (not
applicable to all models)
00~1 00~1
0: N.O.
1: N.C.
E19
LFAn
Lowest Fan speed in Auto fan mode
0
0~1
0
0~1
0: stop
1: low
E20
Pct Output Percentage (not used) 00~100 00~100 1%
E21
devH Device instance no. - Hi bytes 100 0~4194
100
0~4194 1
E22
dEUL** Device instance no. - Low bytes 1
0~999
(ifID-
H <=
4193)
0~302 ( if ID-
H
= 4194)
1
0~999
(ifID-H
<=4193)
0~302 ( if
ID-H
= 4194)
1
E23
UdP**
UDP port number
47808
(BAC0)
0~65535
(0~FFFF)
47808
(BAC0)
0~65535
(0~FFFF
)
1
E24
rHSt Relative Humidity Offset 0 0
-30.0
～30.0
0.1%RH
E
25 F-Ht Fan Output for Heating 0 0/1 0 0/1 0: Disable
1: Enable
E2
6dLyC Cooling Stage Delay
3 1~3 3 1~3 1 (minutes)
E2
7 cycC Cooling Maximum Cycles per
Hour
4 2~6 4 2~6
1 (cycles/hour)
E28
dLyH Heating Stage Delay
3 0~3 3 0~3 1 (minutes)
E29
cycH Heating Maximum Cycles per
Hour
4 2~255 4 2~255
1 (cycles/hour)