Honeywell FocusPRO TH5110D User manual

FocusPROTM TH5000 Series
Non-Programmable Digital Thermostat
® U.S. Registered Trademark. Patents pending.
Copyright © 2006 Honeywell International Inc.
All rights reserved.
Installation
Guide
Must be installed by a trained, experienced technician
Read these instructions carefully. Failure to follow these instructions
can damage the product or cause a hazardous condition.
Need Help?
For assistance with this product please visit http://yourhome.honeywell.com
or call Honeywell Customer Care toll-free at 1-800-468-1502
69-1922EF
This manual covers the following models
• TH5110D: For 1 Heat/1 Cool systems
• TH5220D: For up to 2 Heat/2 Cool systems
(Remove battery holder to find model number)
System Types
• Gas, oil, or electric heat with air
conditioning
• Warm air, hot water, high-
efficiency furnaces, heat pumps,
steam, gravity
• Heat only — two-wire systems,
three-wire zone valves (Series
20), and normally open zone
valves
• Heat only with fan
• Cool only
• 750 mV heating systems
OBSOLETE

Installation Guide
2
Wallplate installation
1. Separate wallplate from thermostat.
2. Mount wallplate as shown below.
Drill 3/16” holes for drywall. Drill 7/32” holes for plaster.
Wall anchors
Wallplate
Wire hole Mounting screws
CAUTION: ELECTRICAL HAZARD
Can cause electrical shock or equipment damage. Disconnect power before
beginning installation.
MERCURY NOTICE
If this product is replacing a control that contains mercury in a sealed tube, do not
place the old control in the trash. Contact your local waste management authority for
instructions regarding recycling and proper disposal.
!
Pull here to remove wallplate
from new thermostat.
Remove battery holder.
!
It's easier to grasp the wallplate
and remove it after completely
removing the battery holder.
OBSOLETE

FocusPROTM TH5110 / TH5220
3
Power options
Keep wires in this
shaded area
Connect Cfor primary AC power
(optional if batteries are installed).
Insert batteries for primary
or backup power.
Remove factory-
installed jumper
only for two-
transformer
systems.
Conventional Terminals:
Rc 24VAC power from cooling
transformer
R 24VAC power from heating
transformer
W Heat relay (stage 1)
W2 Heat relay (stage 2)
Y Compressor contactor (stage 1)
Y2 Compressor contactor (stage 2)
G Fan relay
C 24VAC common. For 2 transformer
systems, use common wire from
cooling transformer.
Heat Pump Terminals:
Rc 24VAC power from cooling
transformer
R 24VAC power from heating
transformer
O/B Changeover valve
Y Compressor contactor
G Fan relay
Aux Auxiliary heat relay
E Emergency heat relay
L Sends output when set to Em. Heat
C 24VAC common
Wiring
Terminal designations
Shaded areas below apply only to TH5220D.
TH5110D Rc
Y
W
G
R
C
TH5110D Rc
Y
O/B
G
R
C
TH5220D
RcYWGW2Y2 RC RcYGAuxEL RC
TH5220D
TH5320U
RcYWGW2Y2 RC RcYGAux
E
Y2L RC
TH5320U
TH5110D Rc
Y
W
G
R
C
TH5110D Rc
Y
O/B
G
R
C
TH5220D
RcYWGW2Y2 RC RcYGAuxEL RC
TH5220D
TH5320U
RcYWGW2Y2 RC RcYGAux
E
Y2L RC
TH5320U
OBSOLETE

Installation Guide
4
Wiring
Wiring guide — conventional systems
Shaded areas below apply only to TH5220D.
NOTES
Wire specifications:
Use 18- to 22-gauge thermostat wire.
Shielded cable is not required.
[1] Power supply. Provide disconnect means
and overload protection as required.
[2] Remove jumper for 2-transformer systems.
[3] Optional 24VAC common connection.
[4] Common connection must come from
cooling transformer.
[5] In Installer Setup, set system type to
Heat Only.
[6] In Installer Setup, set system type to
2Heat/2Cool Conventional.
[7] In Installer Setup, set changeover valve to
O or B.
[8] In Installer Setup, set system type to
2Heat/1Cool Heat Pump.
[9] L terminal sends a continuous output when
thermostat is set to Em. Heat. Connect
to Honeywell zoning panels to switch the
panel to Emergency Heat.
[10] Install field jumper between Aux and E if
there is no emergency heat relay.
1H/1C System
(1 transformer)
Rc Power [1]
R [R+Rc joined by jumper]
Y Compressor contactor
C 24VAC common [3]
W Heat relay
G Fan relay
Heat-only System
Rc Power [1]
R [R+Rc joined by jumper]
C 24VAC common [3]
W Heat relay
Heat-only System
(Series 20) [5]
Rc [R+Rc joined by jumper]
R Series 20 valve terminal “R” [1]
Y Series 20 valve terminal “W”
C 24VAC common [3]
W Series 20 valve terminal “B”
Heat-only System
(normally open zone valve) [5]
Rc [R+Rc joined by jumper]
R Power [1]
Y Normally open zone valve
C 24VAC common [3]
1H/1C System
(2 transformers)
Rc Power (cooling transformer) [1, 2]
R Power (heating transformer) [1, 2]
Y Compressor contactor
C 24VAC common [3, 4]
W Heat relay
G Fan relay
Heat-only System
with Fan
Rc Power [1]
R [R+Rc joined by jumper]
C 24VAC common [3]
W Heat relay
G Fan relay
Cool-only System
Rc Power [1]
R [R+Rc joined by jumper]
Y Compressor contactor
C 24VAC common [3]
G Fan relay
2H/2C System
(1 transformer) [6]
Rc Power [1]
R [R+Rc joined by jumper]
Y Compressor contactor (stage 1)
C 24VAC common [3]
W Heat relay (stage 1)
G Fan relay
W2 Heat relay (stage 2)
Y2 Compressor contactor (stage 2)
2H/2C System
(2 transformers) [6]
Rc Power (cooling transformer) [1, 2]
R Power (heating transformer) [1, 2]
Y Compressor contactor (stage 1)
C 24VAC common [3, 4]
W Heat relay (stage 1)
G Fan relay
W2 Heat relay (stage 2)
Y2 Compressor contactor (stage 2)
See [notes] below
RcW RC
RcYWGW2Y2 RC
RcYWGW2Y2 RC
RcYG RC
RcYWG RC RcWG RC
RcYWG RC
RcYW RC
RcY RC
RcW RC
RcYWGW2Y2 RC
RcYWGW2Y2 RC
RcYG RC
RcYWG RC RcWG RC
RcYWG RC
RcYW RC
RcY RC
RcW RC
RcYWGW2Y2 RC
RcYWGW2Y2 RC
RcYG RC
RcYWG RC RcWG RC
RcYWG RC
RcYW RC
RcY RC
RcW RC
RcYWGW2Y2 RC
RcYWGW2Y2 RC
RcYG RC
RcYWG RC RcWG RC
RcYWG RC
RcYW RC
RcY RC
RcW RC
RcYWGW2Y2 RC
RcYWGW2Y2 RC
RcYG RC
RcYWG RC RcWG RC
RcYWG RC
RcYW RC
RcY RC
RcW RC
RcYWGW2Y2 RC
RcYWGW2Y2 RC
RcYG RC
RcYWG RC RcWG RC
RcYWG RC
RcYW RC
RcY RC
RcW RC
RcYWGW2Y2 RC
RcYWGW2Y2 RC
RcYG RC
RcYWG RC RcWG RC
RcYWG RC
RcYW RC
RcY RC
RcW RC
RcYWGW2Y2 RC
RcYWGW2Y2 RC
RcYG RC
RcYWG RC RcWG RC
RcYWG RC
RcYW RC
RcY RC
RcW RC
RcYWGW2Y2 RC
RcYWGW2Y2 RC
RcYG RC
RcYWG RC RcWG RC
RcYWG RC
RcYW RC
RcY RC
OBSOLETE

FocusPROTM TH5110 / TH5220
5
Wiring
Wiring guide — heat pump systems
Shaded areas below apply only to TH5220D.
Thermostat mounting
Align the 4 tabs on the wallplate with
slots on the back of the thermostat,
then push gently until the thermostat
snaps in place.
Push excess wire back into
the wall opening.
Plug wall opening with
non-flammable insulation.
1H/1C Heat
Pump System
Rc Power [1]
R [R+Rc joined by jumper]
Y Compressor contactor
C 24VAC common [3]
O/B Changeover valve [7]
G Fan relay
2H/1C Heat
Pump System [8]
Rc Power [1]
R [R+Rc joined by jumper]
Y Compressor contactor
C 24VAC common [3]
O/B Changeover valve [7]
G Fan relay
Aux Auxiliary heat relay [10]
E Emergency heat relay [10]
L Sends output when set to Em. Heat [9]
See [notes] on page 4.
RcYG RC
RcYGAuxEL RC
RcYGAux
E
L RC
RcYGY2
RcYGAux
E
L RC
Y2
L RC
RcYG RC
RcYGAuxEL RC
RcYGAux
E
L RC
RcYGY2
RcYGAux
E
L RC
Y2
L RC
OBSOLETE

Installation Guide
6
To begin, press and hold the sand FAN
buttons until the display changes.
Function
number Setting
Press s or t to change settings.
Press NEXT to advance to the next function.
Press DONE to exit and save settings.
10
Done Next
Installer setup
Follow the procedure below to configure the thermostat to match the installed
heating/cooling system, and customize feature operation as desired.
Continued on next page
Setup function Settings & options (factory default in bold)
Shaded areas below apply only to TH5220D.
*[Other cycle rate options: 2, 4, 6, 7, 8, 10, 11 or 12 CPH]
1System type 0 1 heat/1 cool conventional
1 1 heat/1 cool heat pump (no aux. heat)
2 Heat only — 2-wire systems, 3-wire zone valves (Series 20), and
normally open zone valves
3 Heat only with fan
4 Cool only
5 2 heat/1 cool heat pump (with aux. heat)
6 2 heat/2 cool conventional
7 2 heat/1 cool conventional
8 1 heat/2 cool conventional
2Changeover valve
(O/B terminal)
0 Changeover valve (O/B terminal energized in cooling)
1 Changeover valve (O/B terminal energized in heating)
3Fan control
(heating)
0 Gas or oil furnace — equipment controls fan in heating
1 Electric furnace — thermostat controls fan in heating
5Stage 1 heat cycle
rate (CPH: cycles/hour)*
5 For gas or oil furnaces of less than 90% efficiency
1 For steam or gravity systems
3 For hot water systems & furnaces of over 90% efficiency
9 For electric furnaces
6Stage 2 heat cycle
rate/Auxiliary heat
cycle rate (CPH)*
5 For gas or oil furnaces of less than 90% efficiency
1 For steam or gravity systems
3 For hot water systems & furnaces of over 90% efficiency
9 For electric furnaces
8Emergency heat cycle
rate (CPH)*
9 For electric emergency heat
1 For steam or gravity systems
3 For hot water systems & furnaces of over 90% efficiency
5 For gas or oil furnaces of less than 90% efficiency
OBSOLETE

FocusPROTM TH5110 / TH5220
7
System test System status
Shaded areas below apply only to TH5220D.
Press s / t to turn system on/off.
Press NEXT to advance to next test.
Press DONE to terminate system test.
Test number System status
10 0
To begin, press and hold the s and t
buttons until the display changes
Installer setup
Setup function Settings & options (factory default in bold)
Shaded areas below apply only to TH5220D.
CAUTION: Compressor protection is bypassed during testing. To prevent equipment
damage, avoid cycling the compressor quickly
!
10 Heating system 0 Heat and fan turn off.
1 Stage 1 heat turns on. Fan turns on if Setup Function 1 is set to 1
or 5 OR Setup Function 3 is set to 1 **See page 6
2 Stage 2 heat turns on
20 Emergency heating
system
0 Heat and fan turn off
1 Heat and fan turn on
2 Stage 2 heat turns on (auxiliary heat)
30 Cooling system 0 Compressor and fan turn off
1 Compressor and fan turn on
2 Stage 2 compressor turns on
40 Fan system 0 Fan turns off
1 Fan turns on
9Stage 1 compressor
cycle rate (CPH)
3 Recommended for most compressors
[Other cycle rate options: 1, 2, 4, 5 or 6 CPH]
10 Stage 2 compressor
cycle rate (CPH)
3 Recommended for most compressors
[Other cycle rate options: 1, 2, 4, 5 or 6 CPH]
12 Manual/Auto
changeover
0 Manual changeover (Heat/Cool/Off)
1 Auto changeover (Heat/Cool/Auto/Off)
2 Auto changeover only (Auto)
14 Temperature
display
0 Fahrenheit
1 Celsius
15 Compressor
protection
5 Five-minute compressor off time
[Other options: 0, 1, 2, 3 or 4-minute off time]
26 Auxiliary heat control 0 Comfort **See page 8
1 Economy
27 Heat temperature
range stops
90 Max. heat temperature setting is 90 °F (32 °C)
[Other options: 40 °F to 89 °F (4.5 °C to 31.5 °C)]
28 Cool temperature
range stops
50 Min. cool temperature setting is 50 °F (10 °C)
[Other options: 51 °F to 99 °F (10.5 °C to 37 °C)]
Installer system test
OBSOLETE

Installation Guide
Honeywell International Inc.
1985 Douglas Drive North
Golden Valley, MN 55422
http://yourhome.honeywell.com
Automation and Control Solutions
® U.S. Registered Trademark.
© 2006 Honeywell International Inc.
69-1922EF M.S. 03-06
Honeywell Limited-Honeywell Limitée
35 Dynamic Drive
Scarborough, Ontario M1V 4Z9
Printed in U.S.A. on recycled
paper containing at least 10%
post-consumer paper fibers.
Special function
Auxiliary heat control (Setup Function 26):
• Comfort Setting: The thermostat will prioritize comfort over economy depending on heat
pump performance, load conditions and whether the thermostat is calling for the heat
pump. Raising the temperature just a few degrees will often activate the auxiliary heat.
• Economy Setting: The thermostat will attempt to reach the temperature setting
without activating the auxiliary heat. The thermostat will wait to activate the auxiliary
heat depending on heat pump performance, load conditions and how many degrees the
temperature setting is changed.
Accessories & replacement parts
Please contact your distributor to order replacement parts.
Part Description Part Number Use With
Battery holder 50000951-001 TH5110D
Battery holder 50007072-001 TH5220D
Cover plate assembly* 50001137-001 TH5110D
Cover plate assembly* 50002883-001 TH5220D/TH5110D
12 pack of small cover plates* 50007297-001 TH5110D
12 pack of medium cover plates* 50007298-001 TH5220D/TH5110D
*Use to cover marks left by old thermostats.
Specifications
Temperature Ranges
• Heat: 40° to 90°F (4.5° to 32°C)
• Cool: 50° to 99°F (10° to 37°C)
Operating Ambient Temperature
• 32° to 120°F (0° to 48.9°C)
Shipping Temperature
• -20° to 120°F (-28.9° to 48.9°C)
Operating Relative Humidity
• 5% to 90% (non-condensing)
Physical Dimensions
TH5220D
• 3-9/16” H x 5-13/16” W x 1-1/2” D
91 mm H x 147 mm W x 38 mm D
TH5110D
• 3-7/16” H x 4-1/2” W x 1-5/16” D
86 mm H x 114 mm W x 33 mm D
Electrical Ratings
Terminal Voltage (50/60Hz) Running Current
WHeating 20-30 Vac 0.02-1.0 A
(Powerpile) 750 mV DC 100 mA DC
W2 (Aux) Heating 20-30 Vac 0.02-0.5 A
YCooling 20-30 Vac 0.02-1.0 A
Y2 Cooling 20-30 Vac 0.02-1.0 A
GFan 20-30 Vac 0.02-0.5 A
O/B Changeover 20-30 Vac 0.02-0.5 A
EEmergency heat 20-30 Vac 0.02-1.0 A
LOutput 20-30 Vac 0.02-0.5 A
OBSOLETE

FocusPROMC Série TH5000
Thermostat numérique non programmable
® Marque de commerce déposée aux É.-U. Brevets en instance.
© 2006 Honeywell International Inc.
Tous droits réservés.
Guide
d’installation
Doit être installé par un technicien expérimenté et qualifié.
Lire attentivement ces instructions. Le manquement à suivre ces instructions
peut entraîner des dommages au produit et causer des conditions dangereuses.
Besoin d’aide?
Pour obtenir de l’assistance au sujet de ce produit,
consulter le http://yourhome.honeywell.com ou téléphoner sans frais
au Centre de service à la clientèle de Honeywell au 1-800-468-1502
69-1922EF
Ce guide couvre les modèles suivants :
• TH5110D : Pour 1 système de chauffage et 1 système de climatisation
• TH5220D : Pour 2 systèmes de chauffage et 2 systèmes de climatisation
(Enlever le porte-pile pour trouver le numéro de modèle.)
Types de système
• Chauffage au gaz naturel,
au mazout ou à l’électricité
avec climatiseur
• Fournaises à grand rendement
à air chaud ou à eau chaude ;
thermopompes, systèmes
à la vapeur ou gravitaires
• Chauffage seulement – systèmes
à deux fils, soupapes de zone
à trois fils (Série 20) soupapes
de zones normalement ouvertes
• Chauffage seulement avec
soufflante
• Climatisation seulement
• Systèmes de chauffage de 750 mV
OBSOLETE

Guide d’installation
2
Installation de la plaque murale
1. Séparer la plaque murale du thermostat.
2. Installer la plaque murale tel que décrit
ci-dessous.
Percer des trous de 5 mm (3/16 po)
dans le placoplâtre.
Ancrages muraux
Plaque murale
Trou du fil Vis de montage
MISE EN GARDE : RISQUE DE CHOC ÉLECTRIQUE
Peut causer un choc électrique ou endommager l’équipement. Couper l’alimentation
avant de commencer l’installation.
REMARQUE À PROPOS DU MERCURE :
Si ce produit sert à remplacer une commande qui contient du mercure dans un tube
scellé, ne pas jeter la vieille commande aux ordures. Consulter l’administration locale
de gestion des déchets pour connaître les instructions relatives au recyclage
et à l’élimination.
!
Tirer ici pour enlever la plaque
murale du thermostat neuf.
Retirer le porte-pile.
!
Il est plus facile de saisir la
plaque murale et de l’enlever
après avoir complètement
retiré le porte-pile.
Percer des trous de 5,5 mm
(7/32 po) si le mur est en plâtre.
OBSOLETE