CONTINENTAL EDISON CELED32HD22B7 User manual

1
CELED32HD22B7
TV LED HD 31.5
Guide d’utilisation – Instruction manual

2
IMPORTANT WARNINGS AND SAFETY ADVICE
We invite you to read this user manual carefully and completely
before installing and using your device.
It is important that this user manual be kept with the device for
further consultation. If this device is to be transferred to another
person, make sure the user manual follows the device so that the
new user can be informed of the operation of the device.
The warning sign showing a lightning bolt in a
triangle indicates that this product contains
"dangerous electrical voltages".
CAUTION: TO AVOID THE RISK OF
ELECTROCUTION, DO NOT
REMOVE THE COVER (OR THE
BACK OF THE DEVICE).
NO PARTS ARE REPLACEABLE BY THE USER. PLEASE CONTACT
QUALIFIED PERSONNEL IN CASE OF FAILURE.
CAUTION
RISK OF ELECTRIC SHOCK POWERED
DEVICE
DO NOT OPEN
The warning sign showing an exclamation point in a
triangle indicates that this point of the manual
requires special attention.

3
CAUTION: - TO REDUCE THE RISK OF FIRE, ELECTRIC
SHOCK OR SERIOUS INJURY:
●This device must only be connected to a mains network whose
characteristics are identical to those shown on the device
identification plate.
●If it is a class I appliance, the user’s protection is grounded. The
appliance must be connected to a power supply base with a
connection to the protective earth.
●If the product does not bear the logo, it is a Class I device. It
must then be connected to a mains socket with a protective earth
connection.
●If this device bears the logo , it is a class II electrical device in
which the protection against electric shock is not based solely on
the main insulation but on a double insulation. It does not have
protective grounding.
●The mains plug must always be easily accessible. It serves as a
mains disconnecting switch of the device.
●To disconnect the device from the mains, the plug must be
disconnected. Hold the mains cable by its plug. Do not pull on the
mains cable to disconnect the plug.
●The mains cables must be routed so that they are not trampled
upon or pinched by objects placed on or against them.
●If the mains cable of the device is damaged, it must be replaced
by the manufacturer, its after-sales service or a similarly qualified
person to avoid any danger.
●The device must not be exposed to dripping or splashing water,
moisture or liquids.

4
●Do not place the device near water, for example in a bathroom or
near a sink.
●No objects filled with liquids such as vases should be placed on or
above the device.
●Never touch the mains cable with wet hands, this could cause a
short circuit or electric shock.
●To avoid the risk of fire, do not place sources of open flames, such
as lighted candles, or heat sources such as radiators, on or near
the device.
●The device is intended for use only in a temperate climate.
●If smoke, an unusual odour or strange noise is emitted by the
device: unplug the mains cable from the electrical outlet and
consult the after-sales service or repair centre. Never attempt to
make repairs yourself, this could be potentially dangerous.
●Do not attempt to open or disassemble the device. This would
expose you to dangerous voltages.
●The slots and openings of the device are intended for ventilation
and to ensure its operation. To prevent overheating, these
openings must not be obstructed or covered in any way, such as by
newspapers, tablecloths or curtains.
●Always leave a minimum distance of 10 cm around the device for
sufficient ventilation.
●Never push any object into the device through one of its
openings, as it may come into contact with electrical components,
which can cause an electric shock or fire.
●In case of thunderstorm or lightning, immediately unplug the
mains cable from the wall outlet.
●Always turn off the device when not in use. Unplug the mains
cable from the electrical outlet when the device will not be used
for a long period of time.

5
●Unplug the device from the electrical outlet before cleaning. Do
not use liquid or aerosol cleaners. Use a dry, soft cloth for
cleaning.
CAUTION: TO AVOID RISK OF INJURY OR DAMAGE TO
THE PRODUCT OR OTHER EQUIPMENT:
●This product is intended for household and personal use only. Do
not use this product for commercial, industrial or other purposes.
●Do not subject the product to strong shocks, extreme
temperatures or direct sunlight for prolonged periods.
●Keep the product away from magnetic objects, motors and
transformers.
●Do not use the product outdoors, regardless of weather
conditions.
●Install the device only on a stand (furniture, wall…) that can
support its weight safely.
●WARNING: Never place a TV in an unstable place. This can fall,
causing injuries or even the death of a person. Many injuries,
especially in the case of children, can be avoided by taking simple
precautions such as:
-The use of furniture or stands recommended by the TV
manufacturer.
-The exclusive use of furniture that can support the weight of the
TV safely.
-Make sure that the device does not protrude from the edge of
the furniture on which it is placed.
-Never place the device on a tall piece of furniture (e.g. cabinets
or bookcases) without attaching both the furniture and the
device to a suitable stand.
-Do not place the device on a trolley or on a stand that is not
stable. Do not install the device on any fabric or other materials

6
placed between its base and the supporting furniture. The
device could fall and be damaged or seriously injure a person.
-Do not use or watch the TV while driving. This is dangerous, and
illegal in some countries.
-Explain to children the dangers they face when climbing on the
furniture to reach the device or its controls.
-If you keep this device and change the location, you should
apply the same considerations.
-CAUTION: to avoid accidents, this device must be securely
attached to the floor or wall according to the installation
instructions.
CAUTION: TO AVOID EYE HAZARDS:
●It is best to have soft indirect lighting to watch TV. Avoid
completely dark environments and any reflection on the screen, as
these can cause eyestrain.
USE AND HANDLING OF BATTERIES:
●CAUTION: danger of explosion if the batteries are not inserted
correctly or if they are replaced by a non-similar or incompatible
model.
●Replace the batteries only with batteries of the same type
AAA/LR03.
●Batteries must not be exposed to excessive heat such as that
from the sun, fire or similar origin.
●Never throw batteries into fire and never expose them to heat
sources.
●Do not mix different types of batteries, or new and used
batteries.
●The batteries must be inserted according to the polarities

7
indicated on the battery and in the battery case of the remote
control.
●Used batteries must be removed from the remote control.
●The batteries must be disposed of safely at the assigned specific
collection points to preserve the environment. Follow the disposal
instructions indicated on the batteries and at the collection points.
●Keep batteries out of the reach of children and animals. Only
adults are capable of handling the batteries.
For installation, handling, cleaning and disposal of the device, refer to
the following chapters of the user manual.
To avoid possible hearing damage, do not listen at a
high sound level for a long time.
SIMPLIFIED EU DCLARATION OF CONFORMITY:
Continental Edison, declares that the radioelectric equipment type
CELED32HD22B7 is in compliance with Dicrective 2014/53/EU. The full text of
the EU declaration of conformity is available at the following internet address:
https://notice.continentaledison.fr/

8
CONTENTS
I. DESCRIPTION OF THE UNIT........................................................................................................................ 9
A. Description of the TV Set ....................................................................................................................... 9
B. Remote control.................................................................................................................................... 11
II. TECHNICAL SPECIFICATIONS.................................................................................................................... 13
III. INSTALLATION.......................................................................................................................................... 15
A. Unpacking ............................................................................................................................................ 15
B. Wall mounting ..................................................................................................................................... 15
C. Installing the stand legs ....................................................................................................................... 16
D. Basic connections ................................................................................................................................ 17
IV. USE........................................................................................................................................................... 21
A. First-time installation........................................................................................................................... 21
B. Main menu (TV settings) ..................................................................................................................... 21
C. Basic applications ................................................................................................................................ 22
D. Settings ................................................................................................................................................ 27
1. CHANNEL.............................................................................................................................................. 27
2. PICTURE ............................................................................................................................................... 29
3. SOUND ................................................................................................................................................. 30
4. TIME..................................................................................................................................................... 31
5. SETUP................................................................................................................................................... 32
6. LOCK..................................................................................................................................................... 34
V. MAINTENANCE AND CLEANING............................................................................................................... 38
VI. TROUBLESHOOTING TIPS......................................................................................................................... 39
VII. WARRANTY .............................................................................................................................................. 41
VIII. DISPOSAL ................................................................................................................................................. 42
This user guide, any updates or new versions are available on our website.
2011/65/EU (Restriction of the use of certain hazardous substances in electronic equipment)
The CE marking indicates that the product meets the main requirements of the European Directives 2014/35/EU (Low
Voltage), 2014/30/EU (Electromagnetic Compatibility), 2014/53/EU (Radio Equipment), 2011/65/EU (Restriction of the
use of certain hazardous substances in electronic equipment).

9
I. DESCRIPTION OF THE UNIT
A. Description of the TV Set
Front view of the TV set
1. LED display screen
2. Remote control sensor
Power indicator- In standby mode the indicator light will display red color; when switching on the unit the indicator light will
display blue color.
POWER button- To turn ON/OFF the TV.
3. Stand holder

10
Rear view of the TV set
1. POWER CORD: to connect the TV to a power socket.
2. EARPHONE or HEADPHONE OUTPUT: to connect a 3.5 mm earphone jack plug.
3. HDMI1 / HDMI2 : allows the broadcasting of an uncompressed digital video and audio signal via a
single cable.
4. VGA: VGA input terminal.
5. PC AUDIO:PC AUDIO input terminal.
6. CI+: CI input terminal.
7. Mini YPbPr: to connect the YPbPr cable of a VCR or DVD player.
8. Mini AV: to connect a DVD player or VCR to the source.
9. USB1 / USB2 (5V 0.5A): to connect a USB device, such as a storage device to access the TV's
media functions.
10. COAXIAL: COAXIAL output terminal.
11. ANT: to connect the coaxial cable of a terrestrial antenna.

11
B. Remote control
1- POWER (STANDBY)
To turn the TV on or off.
2- TV/RADIO
To switch between TV and radio modes.
3- COLORED Buttons
The colored buttons are used in the sub-menus.
4- SUBTITLE
To show or hide subtitles.
5- TEXT
To display the teletext.
6- TVG
To display the digital program guide.
7- HOLD
Play/Pause in teletext mode.
8- AUDIO
To select an audio file.
9-
To pause the current DTV program, and start recording in the
background, Play/Pause (in USB mode).
10- /SUBPAGE
To display the teletext sub page. / To fast forward.
11- /Size
For quick return. / Press repeatedly to change the size of the
teletext.
12- BUTTON
To start SAVING a digital program (in DTV mode).
13-
To stop playback in Multimedia mode.
14- / INDEX
To read the following file./ To display the teletext index.
15- / FAV
To play the previous file. / To display the list of favourite
programs.
16- MENU
To display the main menu or the previous menu.
17- SOURCE
To change the video source.
18- OK
To confirm the selection.

12
19- ▲/▼/◄/►
Navigation keys.
20- EXIT
To exit the sub-menu page.
21- ASPECT
Press repeatedly to change the image size
22- MUTE
To mute the sound.
23- VOL+/VOL-
To raise or lower the volume.
24- CH +/ CH –
To display the next or previous channel.
25- INFO
To display the source and available information
about a program.
26- NUMERIC BUTTONS
Press the button to directly enter the number of the channel
you want to view.
27- -/--
To change the digits.
28- PREVIOUS BUTTON
To return to the previous channel.

13
II. TECHNICAL SPECIFICATIONS
Article number
CELED32HD22B7
Model
DVB-PM1320162HCAT
Display
31.5" LED HD
Resolution
1366 x 768 pixels
Colour display
16.7M
Contrast
3000 :1
Ratio
16 :9
Tuner
DVB-T/T2/C
TV power supply
AC 100-240V~50/60Hz
Consumption
60W
Dimensions
732 (W)×191(D)×480(H)mm
Weight
Approx. 3.41 Kg
Stand
2 piece dismountable
Operating temperature range
-5°C to 45°C
Remote control power supply
3V (2 x LR03/AAA 1.5V batteries not included)
USB ports voltage and current
5V 0.5A
Hotel Lock
Yes
Speaker
Built-in 2 x 8W
Inputs
Antenna, HDMI, Mini YPbPr, Mini AV, VGA, PC AUDIO, USB, CI+
Outputs
COAXIAL, Headphones
USB functions
DVR (digital video recorder)
USB multimedia playback
formats
Video : AVI, MPG (MPEG 1/2)
Music : MP3
Photos : JPEG, JPG
Text : TXT
These specifications are subject to change without notice.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo are
registered trademarks of HDMI Licencing LLC in the United States and other countries.

14
ACCESSORIES :
Stand …..……...….............................................................................................2 pieces
Remote control ...............................................................................................................1 piece
Instruction manual ...............................................................................................................1 piece
The images provided in this manual are for information only, refer to the actual product for confirmation.
ENERGY RATING LABEL
Brand
CONTINENTAL EDISON
Article number
CELED32HD22B7
(Model: DVB-PM1320162HCAT)
Energy efficiency class
F
Visible diagonal display
80 cm; 31 inches
Power consumption in running mode (W)
27 W
Power consumption (kWh per year), based on the
electricity consumption of a television set operating four hours a day for
three hundred and sixty-five days. Actual consumption depends on the
conditions of use of the television set.
31 kWh/1000h
Power consumption in standby mode (W)
<0.5 W
Power consumption in off-mode (W)
-
Screen resolution (pixels)
1366 x 768

15
III. INSTALLATION
A. Unpacking
Your TV should be unpacked and handled by 2 people, to avoid any risk of deformation or impact on the
LED display.
Start by preparing a flat surface covered with a soft, thick fabric (a blanket, for example). The prepared
surface area must be larger than the size of the TV. This will allow the TV to be laid flat with the LED screen
facing the floor.
Before removing the TV from its packaging, read the sections "Wall Mounting" and "Stand Legs Installation"
to prepare yourself for the installation operation you have chosen.
Remove the TV from its packaging by lifting it vertically, then place the TV screen flat on the previously
protected flat surface so that either the stand legs or a wall mounting bracket (not included) can be
attached.
Packaging materials
-The packaging cardboard is recyclable.
-The materials marked with the symbol are recyclable.
->PE< = polyethylene; >PS< = polystyrene; >PP< = polypropylene; ... This means that they
can be recycled by disposing of them in appropriate collection containers.
-Other packaging elements (adhesive, fasteners, etc.) should be disposed of with
household waste.
For more information: www.quefairedemesdechets.fr
B. Wall mounting
Contact a professional for assistance with the wall mounting of your TV set. We cannot be held
liable for any damage or injury caused by the mounting of the TV set.
The TV must be mounted on a vertical wall. This TV is not intended for installation on a sloped
wall.
The TV must be turned off and disconnected from the power supply when you mount it to the
wall. Failure to comply with these precautions may result in electric shock or electrocution.
The mounting bracket must correspond to the centre distances indicated below.
NOTE: The screws supplied are used for fixing the stand legs only. If you want to mount the TV on a wall,
contact a professional to find out how to install a wall bracket.
Rear view of your TV set

16
C. Installing the stand legs
Your TV set comes with uninstalled stand legs. Before using this TV as a free-standing unit on a furniture,
install the stand legs as shown below.
Step 1
Place the TV flat, with the screen facing down, on a flat surface
covered with a soft, thick cloth to prevent damage.
The bottom edge of the TV should protrude slightly from the
edge of the flat surface, to allow the stand legs to be fixed
without damaging the LED display.
Step 2
Align the bottom of the TV with the stand legs until they are
fully in place (aligned mounting holes).
Step 3
Tighten the supplied screws with a screwdriver.
NOTE: unplug the TV from the AC outlet when installing or removing the TV legs.
Contact one of our distributors to learn more about how to install and remove the TV legs.

17
D. Basic connections
Make sure that all cables are disconnected from the main unit before connecting the power cord
plug to the wall outlet.
Read the instructions carefully before connecting any other device.
Connect to an external antenna (ANT)
Connect an antenna to the antenna terminal to obtain the best possible image quality. The use of antenna
amplifiers is optional or depends on the type of external antenna used.
Mini AV connection
Rear of the external terminal
AV cable
(not provided)

18
NOTE: when connecting an external device, match the color of the terminal to the color of the cable.
Mini YPbPr connection
NOTE: when connecting an external device, match the color of the terminal to the color of the cable.
CI input terminal
USB input terminal
Rear of the external terminal
AUDIO cable (not provided)
YPbPr cable (not provided)
The CI card is not provided.
The USB stick is not provided.

19
PC/VGA connection
HDMI connection
Audio cable
(Not included)
VGA cable
(Not included)
Use an HDMI cable to connect
the TV to another device to
receive a high-definition
multimedia signal.
Rear of the external terminal
HDMI cable (not provided)
Use VGA cable and Audio
cable to connect the unit with
TV or PC, and use this
product as a monitor.

20
Coaxial connection
Earphone/headset connection
BEFORE PROCEEDING, MAKE SURE THAT ALL EQUIPMENT AND POWER CORDS ARE CONNECTED AND
CONFIGURED PROPERLY.
Headphone and headset cable (not included)
Use coaxial cable (not included) to connect the unit
with amplifier or other audio decoding devices for
coaxial audio signal output.