Continuum 600/1200 Series User manual

Continuum 600/1200 Series (PA-7100) Service Announcement
(8/12/98)
Revision History
12/23/97 - Revision 2.
02/24/98 - Updated Section 4; Added Section 6.
03/31/98 - Updated Section 8.4.
05/07/98 - Added Model 615 to Section 4.1.
06/02/98 - Updated Section 4.1.
06/16/98 - Updated Section 1 and Section 3.1.
06/22/98 - Updated Section 3.3.
07/06/98 - Reformatted Document.
07/20/98 - Updated Section 3.3.
07/27/98 - Updated Sections 4.1 and 4.3.
08/07/98 - Updated Section 6.1.
08/12/98 - Updated Section 4.1.
1. Overview
The Continuum 600/1200 Series systems are the first Stratus RISC systems based on the Hewlett Packard PA-RISC
HP7100 microprocessor and a new system bus architecture. The Series 600 is an entry-level to mid-range system
designed around a 6-slot backplane in the Central Electronic Cabinet (CEC). The Series 1200 version is an
expandable high-end system featuring a 12-slot CEC backplane.
The CEC cabinet main chassis boards in the 600/1200 Series include the following:
CPU-Memory Board - The CPU-Memory board is available in two designs: uniprocessor (one logical/ two
physical CPUs) and twin processor (two logical/four physical CPUs). Both are available in 72 or 96 MHz
versions with 256 KB instruction cache (Icache) and 256 KB data cache (Dcache) or 1 MB Icache and 1 MB
Dcache. Memory sizes range from 128 MB to 512 MB using 128-MB (M702) memory modules, or 512 MB to
2 GB using 512-MB (M713) memory modules. For the most current information on available memory refer to
the Continuum Memory Subsystem Technical Reference. The document is also available in PDF format.at
http://www.cac.stratus.com/CSDoc/home/continuum600.htm
.

SCSI-ENET Controller - The SCSI-ENET controller is the interface between the system bus and the SCSI
and Ethernet I/O devices. It contains four differential SCSI interface ports (used for interfacing with mass
storage devices such as the D700 disk/tape subsystem and T204/T403 tape drives) and one Ethernet port. Each
pair of SCSI-ENET controllers can support up to 48 physical disk drives.
IO Processor - The IO processor manages IO operations, primarily to IOA communications adapters and
certain peripheral devices. It interfaces the system bus to two 8-bit IO busses. Each pair of IO processors can
support two IOA chassis.
K470 PMC I/O Controller - High-speed I/O subsystem based on the Peripheral Component Interconnect
(PCI) bus. It provides interconnect to the system backplane for up to three PCI I/O adapters in PMC (PCI
Mezzanine Card) form factor.
CPU-Memory boards reside in four dedicated slots in the backplane. The remaining slots are configured with
SCSI-ENET controllers or IO processors. Recommended slot assignments for various models are shown later in this
document.
The CEC cabinet in an AC system contains an AC/DC power system that provides 3600 watts of N+1 DC power.
The AC/DC power system residing in each expansion cabinet (except the AC peripheral cabinet, which has no power)
provides 2400 watts of N + 1 DC power.
Continuum systems are also designed to be fully Central Office (CO) installable utilizing -48 V DC input power. Each
CEC cabinet and DC expansion cabinet in a CO system contains two DC power controllers.
There is no physical control panel on Continuum 600/1200 Series systems. Operating commands are entered at the
system console which is connected to the system via the Console Controller card in the CEC cabinet.
2. Operating System Requirements
FTXVOSSystem
Minimum release 3.0Minimum release 13.0AC systems
Minimum release 3.0Minimum release 14.0.1DC systems
3. Hardware Components
NOTE: The hardware components shown in the following tables are at the base minimum revisions
approved for operation at the time of publication. For current revision requirements and complete revision
history, refer to theHQ Service Support Rev Dir.
3.1 Main Chassis Boards
NOTE: Models G731-G748 contain 128-MB memory modules; models G751-G758 contain 512-MB
memory modules.
NOTE: Although their descriptions are similar, models G731 thru G748 (sub model 00) are not
compatible with models G731 thru G748 (sub model 20). If used together, a sub model mismatch
failure will be generated.

Minimum OS Release
Description
Model
VOS
13.0
72 MHz CPU-Memory (Uniprocessor, 128-512 MB memory, 512 KB cache)
G731-G734
(sub model 00)
13.1
72 MHz CPU-Memory (Uniprocessor, 128-512 MB memory, 512 KB cache)
G731-G734
(sub model 20)
13.0
72 MHz CPU-Memory (Twin processor, 128-512 MB memory, 512 KB cache)
G735-G738
(sub model 00)
13.1
72 MHz CPU-Memory (Twin processor, 128-512 MB memory, 512 KB cache)
G735-G738
(sub model 20)
13.096 MHz CPU-Memory (Uniprocessor, 128-512 MB memory, 2 MB cache)
G741-G744
(sub model 00)
13.1
96 MHz CPU-Memory (Uniprocessor, 128-512 MB memory, 2 MB cache)
G741-G744
(sub model 20)
13.0
96 MHz CPU-Memory (Twin processor, 128-512 MB memory, 2 MB cache)
G745-G748
(sub model 00)
13.2.1
96 MHz CPU-Memory (Twin processor, 128-512 MB memory, 2 MB cache)
G745-G748
(sub model 20)
96 MHz CPU-Memory (Uniprocessor, 512 MB-2 GB memory, 2 MB cache)
G751-G754
(sub model 20)
96 MHz CPU-Memory (Twin processor, 512 MB-2 GB memory, 2 MB cache)
G755-G758
(sub model 20)
13.0**
SCSI-ENET controller
K450*
13.2HSC SCSI-ENET controllerK460*
13.0
IO processor K600
14.1PMC I/O ControllerK470
* K460 has replaced the K450.
** Release 13.1 for Ethernet support.
3.2 IOA Boards
3.2.1 K-Cards
Minimum OS Rel.

DescriptionChassis LabelTypeModel
FTXVOS
NA
13.0Full-modem mcommCOMM ADAPTER1K101
NA
13.0Full-modem mcommCOMM1BK101-20
3.0
13.0Full-modem ucomm - RS-232/422COMM ADAPTER2K102
3.0
13.0Full-modem ucomm - RS-232/422COMM ADAPTER2AK102-10
3.0
13.0Ethernet ETHERNET ADAPTER.1K104
3.0
13.0
Ethernet low powerETHERNET ADAPTER.1AK104-10
3.0
13.0 Terminator TERM 2 K108-10
3.0
13.0 Full-modem ucomm - RS-232/423 COMM ADAPTER 4 K109
NA
13.0IBM (L322) printerPRINTER ADAPTER1 K110
3.0
13.0Full-modem ucomm - RS-232/V.35
COMM ADAPTER
6
K112
3.013.0Full-modem ucomm - RS-232/V.35COMM ADAPTER6K112-30
Full-modem ucomm - RS-232/V.35COMM ADAPTER6K112-40
NA
13.1Channel attach interfaceCHANNEL1K113-01

3.0
13.0X.21/RS-232 COMM8K114
X.21/RS-232 COMM8
K114-10
NA
13.0Token ring TOKEN RING8K115
NA13.0Token ringTOKEN RING8K115-10
3.0
13.016-port asyncCOMM ADAPTER9K118
3.0
13.1DataKit VCS interfaceCOMM11K120
3.0
13.0ISDN X.25 primary rateCOMM12K124
3.013.0ISDN X.25 primary rateCOMM12AK124-10
ISDN X.25 primary rateCOMM12A
K124-20
3.0NAISDN X.25 basic rateCOMM13K125
3.0.1
NANEC printerPRINT2K127
3.2.2 PMC Cards
Note: The PMC cards shown in the following table are based on information available at the time of
publication. For current (and more detailed) PMC information refer to thePCI/PMC Adapter Technical
Reference. The document is also available in PDF format at
http://www.cac.stratus.com/CSDoc/home/comm.htm.
Min. FTX ReleaseMin. VOS ReleaseSpeedModel No.Adapter
VOS 14.1100 MbpsU713Ethernet
VOS 14.14/16 MbpsU720Token Ring
VOS 14.1100 MbpsU730FDDI
VOS 14.2155 MbpsU741ATM
3.3 Peripherals
Note: The disk and tape drives shown in the following table are based on information available at the time of
publication. For current (and more detailed) disk information refer to theContinuum Disk Drives Technical
Reference
. The document is also available in PDF format at
at

http://www.cac.stratus.com/CSDoc/home/disk.htm
.
For more information on tape drives, refer to the
DDS
DAT Tape Drive Technical Reference. The document is also available in PDF format at
http://www.cac.stratus.com/CSDoc/home/tape.htm.
Minimum OS Release
DescriptionModel FTXVOS
3.013.01 GB (5400 rpm, 3 1/2") disk drive D701*
3.013.02 GB (5400 rpm, 3 1/2") disk drive D702**
3.0.0.113.0.11 GB (7200 rpm, 3 1/2") disk drive D703*
3.1.113.0.12 GB (7200 rpm, 3 1/2") disk driveD704
3.1 with patch13.3.22 GB (7200 rpm, 3 1/2") disk driveD704-10
3.1.113.0.14 GB (7200 rpm, 3 1/2") disk driveD705
3.1.113.1.14 GB (7200 rpm, 3 1/2") disk driveD705-10
3.1 with patch13.3.14 GB (7200 rpm, 3 1/2") disk driveD705-20
3.1 with patch13.3.1 with patch4 GB (7200 rpm, 3 1/2") disk driveD705-30
3.213.3.29 GB (7200 rpm, 3 1/2") disk driveD706
3.213.3.29 GB (7200 rpm, 3 1/2") disk driveD706 -10
3.414.118 GB (7200 rpm, 31/2") disk driveD707
3.0.113.16250 bpi 1/2" SCSI tape drive T204-001
3.0.113.16250 bpi 1/2" SCSI tape drive (table top)T204-002
3.0.113.13480/3490 media-compatible tape drive (1 drive)T403-001
3.0.113.13480/3490 media-compatible tape drive (2 drives)T403-002
3.0.113.13480/3490 media-compatible tape drive(1 drive, table top)T403-003
3.414.24-GB, 3490E media-compatible, tape drive (10-cartridge)T404
3.0.113.14-mm DAT II (3 1/2") tape driveT701
3.0.113.14-mm DAT II (3 1/2") tape drive with autoloaderT702
3.213.4/14.2QIC 525-MB/1.2-GB cartridge tape driveT704
3.314.012-GB, DDS3 DAT tape drive (1 cartridge)T705
3.314.072-GB, DDS3 DAT tape drive (6-cartridge autoloader)T706
13.1Channel interface unit (CIU)U201
13.1Dual channel interface unitU201-01
3.0.113.2Remote I/O (RIO) (standalone/external)U250
3.0.113.2Remote I/O (RIO) (cabinet mounted)U250-10

3.013.0Band printer (600 lpm, 110 volt)
L306-10
3.013.0Band printer (600 lpm, 220 volt)L306-20
Band Printer (900 lpm, 110/220 volt)L401
3.013.0RSN modem (9600 bps)C319
RSN modem (14400 bps)C419
3.4NACD-ROM driveD758
* The D701 and D703 are no longer sold.
** The D702 has been replaced by the D704.
3.4 Expansion Cabinets
Minimum OS
Release
VOS FTX
DescriptionModel
3.0
13.0 Used on all Central Office systems. Contains an internal DC power controller. E601
3.0
13.0 Used on all AC systems. Contains an internal 2400W AC/DC power system. E610
3.0
13.0 (13.1 for
channel attach
Used for housing AC peripherals (T204-001 and T403-001/002 tape drives, U201
CIU for channel attach, and U250-10 remote I/O)
E612
3.0
13.0 Contains no power. Used for housing DB25 interconnect panels for the K118,E612-NP
4. System Configurations
NOTE: The configurations shown in the following tables are based on information available at the time
of publication. For current (and more detailed) configuration information refer to theContinuum Series
600/1200 Configuration Specification(ES-000076).
4.1 Series 600 Configurations
Model 620
Model 615S
(VOS OS
only)***
Model 615**Model 610
Model 610S
(VOS OS only)
Component
G735-G738
G741G741-G744
G731-G734G731
CPU-Memory board

2
22
2
2
# CPU-Memory boards
2
11
11
# Logical CPUs
Min. = 256 MB
Max. = 512 MB
Min. = 128 MB
Max. = 128 MB
Min. = 128 MB
Max. = 512 MB
Min. = 128 MB
Max. = 512 MB
Min. = 128 MB
Max. = 128 MB
Duplexed memory
(M702 128-MB memory
modules)
NANA
Min. = 1 GB
Max. = 2 GB
NANA
Duplexed memory
(M713 512-MB memory
modules)*
Min. = 0
Max. = 2
Min. = 0
Max. = 2
Min. = 0
Max. = 2
Min. = 0
Max. = 2
Min. = 0
Max. = 2
# IO processors
Min. = 2
Max. = 4
Min. = 2
Max. = 2
Min. = 2
Max. = 4
Min. = 2
Max. = 4
Min. = 2
Max. = 2
# SCSI-ENET
controllers
Min. = 0
Max. = 1
Min. = 0
Max. = 1
Min. = 0
Max. = 1
Min. = 0
Max. = 1
Min. = 0
Max. = 1
# CEC IOA chassis
(11-slot)
Min. = 0
Max. = 2
Min. = 0
Max. = 0
Min. = 0
Max. = 2
Min. = 0
Max. = 2
Min. = 0
Max. = 0
# Expansion IOA chassis
(16-slot)
Min. = 2
Max. = 16
Min. = 2
Max. = 2
Min. = 2
Max. = 16
Min. = 2
Max. = 16
Min. = 2
Max. = 2
# D700 disk/tape
enclosures
Min. = 2
Max. = 96
Min. = 2
Max. = 10
Min. = 2
Max. = 96
Min. = 2
Max. = 96
Min. = 2
Max. = 10
# Disk drives (VOS
systems)
Min. = 2
Max. = 84
NA
Min. = 2
Max. = 84
Min. = 2
Max. = 84
NA
# Disk drives (FTX
systems)
Min. = 1
Max. = 4
Min. = 1
Max. = 4
Min. = 1
Max. = 4
Min. = 1
Max. = 4
Min. = 1
Max. = 4
# Tape drives
Min. = 0
Max. = 3
Min. = 0
Max. = 0
Min. = 0
Max. = 3
Min. = 0
Max. = 3
Min. = 0
Max. = 0
# Expansion cabinets
* Available on G755-G758 (sub model 20) boards only. Requires min. FTX 3.2 (with patch) or VOS 13.3.3. Marketing ID is M512-1.
** OS releases supported on Model 615: VOS 13.3.3, 14.0, 14.0.1 / FTX 3.2, 3.3.
*** OS releases supported on Model 615S: VOS 13.3.3, 14.0, 14.0.1
4.2 Series 600 Recommended Slot Assignments
Model 625Model 620Model 610Model 610SSlot No.
CPU-MemoryCPU-MemoryCPU-MemoryCPU-Memory0
CPU-MemoryCPU-MemoryCPU-MemoryCPU-Memory1
SCSI-ENETSCSI-ENETSCSI-ENETSCSI-ENET2
SCSI-ENETSCSI-ENETSCSI-ENETSCSI-ENET3
SCSI-ENET/IOSCSI-ENET/IOSCSI-ENET/IOSCSI-ENET/IO4

SCSI-ENET/IO
SCSI-ENET/IO
SCSI-ENET/IO
SCSI-ENET/IO
5
4.3 Series 1200 Configurations
Model 1245* Model 1225 Model 1220 Model 1215 Model 1210 Component
G745-G748,
G755-G757
G745-G748,
G755-G758
G735-G738
G741-G744,
G751-G754
G731-G734
CPU-Memory
board
42222
# CPU-Memory
boards
42211
# Logical CPUs
Min. = 256 MB
Max. = 512 MB
Min. = 128 MB
Max. = 512 MB
Min. = 128 MB
Max. = 512 MB
Min. = 128 MB
Max. = 512 MB
Min. = 128 MB
Max. = 512 MB
Duplexed memory
(M702 128-MB
memory modules)
Min. = 512 MB
(Available on
VOS systems
only)
Max. = 3 GB
(Available on
VOS systems
only)
Min. = 512 MB
Max. = 2 GB
NA
Min. = 512 MB
Max. = 2 GB
NA
Duplexed memory
(M713 512-MB
memory modules)**
Min. = 0
Max. = 6
Min. = 0
Max. = 6
Min. = 0
Max. = 6
Min. = 0
Max. = 6
Min. = 0
Max. = 6
# IO processors
Min. = 2
Max. = 8
Min. = 2
Max. = 8
Min. = 2
Max. = 8
Min. = 2
Max. = 8
Min. = 2
Max. = 8
# SCSI-ENET
controllers
Min. = 0
Max. = 6
Min. = 0
Max. = 6
Min. = 0
Max. = 6
Min. = 0
Max. = 6
Min. = 0
Max. = 6
# IOA chassis
Min. = 2
Max. = 32
Min. = 2
Max. = 32
Min. = 2
Max. = 32
Min. = 2
Max. = 32
Min. = 2
Max. = 32
# D700 disk/tape
enclosures
Min. = 2
Max. = 190
Min. = 2
Max. = 190
Min. = 2
Max. = 190
Min. = 2
Max. = 190
Min. = 2
Max. = 190
# Disk drives (VOS
systems)
Min. = 2
Max. = 190
Min. = 2
Max. = 190
Min. = 2
Max. = 190
Min. = 2
Max. = 190
Min. = 2
Max. = 190
# Disk drives (FTX
systems)
Min. = 1
Min. = 1
Min. = 1
Min. = 1
Min. = 1

Max. = 4Max. = 4Max. = 4Max. = 4Max. = 4
# Tape drives
Min. =
Max. = 6
Min. = 1
Max. = 6
Min. = 1
Max. = 6
Min. = 1
Max. = 6
Min. = 1
Max. = 6
# Expansion
cabinets
* Minimum OS release: VOS 13.2.1 / FTX 3.2.
** Available on G751-G758 (sub model 20) boards only. Requires min. FTX 3.2 (with patch) or VOS 13.3.3. Marketing ID is
M512-1.
4.4 Series 1200 Recommended Slot Assignments
1245 1225 1220 1215 1210 Slot No.
CPU-MemoryCPU-MemoryCPU-MemoryCPU-MemoryCPU-Memory0
CPU-MemoryCPU-MemoryCPU-MemoryCPU-MemoryCPU-Memory1
CPU-Memory--------------------------------------------------------2
CPU-Memory-------------------------------------------------------3
SCSI-ENETSCSI-ENETSCSI-ENETSCSI-ENETSCSI-ENET4
SCSI-ENETSCSI-ENETSCSI-ENETSCSI-ENETSCSI-ENET5
SCSI-ENET/IOSCSI-ENET/IOSCSI-ENET/IOSCSI-ENET/IOSCSI-ENET/IO6
SCSI-ENET/IOSCSI-ENET/IOSCSI-ENET/IOSCSI-ENET/IOSCSI-ENET/IO7
SCSI-ENET/IOSCSI-ENET/IOSCSI-ENET/IOSCSI-ENET/IOSCSI-ENET/IO8
SCSI-ENET/IOSCSI-ENET/IOSCSI-ENET/IOSCSI-ENET/IOSCSI-ENET/IO9
SCSI-ENET/IOSCSI-ENET/IOSCSI-ENET/IOSCSI-ENET/IOSCSI-ENET/IO10
SCSI-ENET/IOSCSI-ENET/IOSCSI-ENET/IOSCSI-ENET/IOSCSI-ENET/IO11
5. Specifications
5.1 Physical
180.3 cm (71 inches)
Height
76.2 cm (30 inches)
Width
99 cm (39 inches)
Depth
544.3 kg (1200 lbs) max.
Weight
5.2 Environmental

Operating temperature (AC and DC systems)
4.5º to 40º C (40º to 104º F)
-200 to 6000 ft
4.5º to 35º C (40º to 95º F)
6000 to 8000 ft
4.5º to 30º C (40º to 86º F)
8000 to 10,000 ft
Short term (<72 hrs) operating temp. (DC systems only)
1.7º to 49º C (35º to 120º F)
-200 to 6000 ft
1.7º to 45º C (35º to 113º F)
6000 to 8000 ft
1.7º to 35º C (35º to 95º F)
8000 to 10,000 ft
Heat dissipation (maximum)
15,131 Btu/hr
CEC cab. (AC systems)
15,131 Btu/hr
Expansion cab. (AC systems)
12,283 Btu/hr
CEC cab. (DC systems)
12,283 Btu/hr
Expansion cab. (DC systems)
10% to 80% non-condensing
Relative humidity
12º/hr C (21.6º/hr F)
Max. rate of temp. change
Acoustical noise (per cabinet)
67 dBAFans at normal speed
77 dBA
Fans at full speed
5.3 Electrical (AC Cabinets)
Two 30A, single-phase AC inputs (1 active, 1 standby)
AC service requirements
AC input voltage range
200 to 240 V AC
Nominal
180 to 264 V AC
Absolute
47 to 63 Hz
AC input frequency range
82%
Efficiency (min.)
>.99 (>10% load)
Power factor
4.44 KVA
AC input power (max.)
Input current (@ 3600 W of power delivered to load)

16.8 A @ 264 V AC
Minimum
22.2 A @ 200 V AC
Nominal 18.5 A @ 240 V AC
24.7 A @ 180 V AC
Maximum
-40.0 to -59.9 V DC
DC output voltage range
-54.5 V DC
Nominal
3600 W
DC output power (max.)
AC line cord (dual; 1 active, 1 standby)
4.6 m (15 ft)
Standard length
7.6 m (25 ft)
Optional length
NEMA 30A, 250V twistlock connector
Termination (domestic)
IEC 309, 32A, 250V pin and sleeve connector
Termination (intl.)
5.4 Electrical (DC Cabinets)
Two 100A DC inputs
DC service requirements
-42.0 to -59.9 V DC
DC input voltage range
-54.5 V DC
Nominal
3650 W
DC input power (max.)
Input current (@ 3600 W of power delivered to load)
61.0 A @ -59.9 V DC
Minimum
67.0 A @ -54.5 V DC
Nominal
87.0 A @ -40.0 V DC
Maximum
3600 W
DC output power (max.)
DC line cord (dual; load sharing)
7.6 m (25 ft)
Standard length
15.2 m (50 ft)
Optional length
Double-holed ring lug connector
Termination
6. Upgrade Kits
6.1 CPU-Memory Board Upgrade Kits
The following table lists the marketing IDs of the CPU-Memory board upgrade kits.

Description
Marketing ID
Upgrade a Model 1215 (1 GB) to a Model 1225 (1 GB).UPC2093
Upgrade a Model 1215 (1.5 GB) to a Model 1225 (1.5 GB).UPC2094
Upgrade a Model 1215 (2 GB) to a Model 1225 (2 GB).UPC2095
Upgrade a Model 1225 (1 GB) to a Model 1245 (2 GB).UPC2097
Upgrade a Model 1225 (1 GB) to a Model 1245 (3 GB).UPC2097-3
Upgrade a Model 1225 (1.5 GB) to a Model 1245 (3 GB).UPC2098
Upgrade a Model 1225 (1.5 GB) to a Model 1245 (2 GB).UPC2098-2
Upgrade a Model 1225 (2 GB) to a Model 1245 (3 GB).UPC2099
Upgrade a Model 610 (128 MB) to a Model 615 (128 MB).UPC2200
Upgrade a Model 610 (128 MB) to a Model 615 (256 MB).UPC2201
Upgrade a Model 610 (128 MB) to a Model 615 (384 MB).UPC2202
Upgrade a Model 610 (128 MB) to a Model 615 (512 MB).UPC2203
Upgrade a Model 610 (128 MB) to a Model 615 (1 GB).UPC2203-2
Upgrade a Model 610 (256 MB) to a Model 615 (256 MB).UPC2204
Upgrade a Model 610 (256 MB) to a Model 615 (384 MB).UPC2205
Upgrade a Model 610 (256 MB) to a Model 615 (512 MB).UPC2206
Upgrade a Model 610 (256 MB) to a Model 615 (1 GB).UPC2206-2
Upgrade a Model 610 (384 MB) to a Model 615 (384 MB).UPC2207
Upgrade a Model 610 (384 MB) to a Model 615 (512 MB).UPC2208
Upgrade a Model 610 (384 MB) to a Model 615 (1 GB).UPC2208-2
Upgrade a Model 610 (512 MB) to a Model 615 (512 MB).UPC2209
Upgrade a Model 610 (512 MB) to a Model 615 (1 GB).UPC2209-2
Upgrade a Model 610 (128 MB) to a Model 625 (1 GB).UPC2013-2
Upgrade a Model 610 (256 MB) to a Model 625 (1 GB).UPC2016-2
Upgrade a Model 610 (384 MB) to a Model 625 (1 GB).UPC2018-2
Upgrade a Model 610 (512 MB) to a Model 625 (1 GB).UPC2019-2
Upgrade a Model 615 (128 MB) to a Model 625 (128 MB).UPC2210
Upgrade a Model 615 (128 MB) to a Model 625 (256 MB).UPC2211
Upgrade a Model 615 (128 MB) to a Model 625 (384 MB).UPC2212
Upgrade a Model 615 (128 MB) to a Model 625 (512 MB).UPC2213
Upgrade a Model 615 (128 MB) to a Model 625 (1 GB).UPC2213-2
Upgrade a Model 615 (256 MB) to a Model 625 (256 MB).UPC2214
Upgrade a Model 615 (256 MB) to a Model 625 (384 MB).UPC2215
Upgrade a Model 615 (256 MB) to a Model 625 (512 MB).UPC2216
Upgrade a Model 615 (256 MB) to a Model 625 (1 GB).UPC2216-2

Upgrade a Model 615 (384 MB) to a Model 625 (384 MB).
UPC2217
Upgrade a Model 615 (384 MB) to a Model 625 (512 MB).UPC2218
Upgrade a Model 615 (384 MB) to a Model 625 ( 1 GB).UPC2218-2
Upgrade a Model 615 (512 MB) to a Model 625 (512 MB).UPC2219
Upgrade a Model 615 (512 MB) to a Model 625 (1 GB).UPC2219-2
Upgrade a Model 615 (1 GB) to a Model 625 (1 GB).UPC2220
Upgrade a Model 615 (1.5 GB) to a Model 625 (1.5 GB).UPC2221
Upgrade a Model 615 (2 GB) to a Model 625 (2 GB).UPC2222
Upgrade a Model 620 (128 MB) to a Model 625 (1 GB).UPC2023-2
Upgrade a Model 620 (256 MB) to a Model 625 (1 GB).UPC2026-2
Upgrade a Model 620 (384 MB) to a Model 625 (1 GB).UPC2028-2
Upgrade a Model 620 (512 MB) to a Model 625 (1 GB).UPC2029-2
Upgrade a Model 1210 (128 MB) to a Model 1215 (1 GB).UPC2033-2
Upgrade a Model 1210 (256 MB) to a Model 1215 (1 GB).UPC2036-2
Upgrade a Model 1210 (384 MB) to a Model 1215 (1 GB).UPC2038-2
Upgrade a Model 1210 (512 MB) to a Model 1215 (1 GB).UPC2039-2
Upgrade a Model 1215 (128 MB) to a Model 1225 (1 GB).UPC2063-2
Upgrade a Model 1215 (256 MB) to a Model 1225 (1 GB).UPC2066-2
Upgrade a Model 1215 (384 MB) to a Model 1225 (1 GB).UPC2068-2
Upgrade a Model 1215 (512 MB) to a Model 1225 (1 GB).UPC2069-2
Upgrade a Model 1220 (128 MB) to a Model 1225 (1 GB).UPC2073-2
Upgrade a Model 1220 (256 MB) to a Model 1225 (1 GB).UPC2076-2
Upgrade a Model 1220 (384 MB) to a Model 1225 (1 GB).UPC2078-2
Upgrade a Model 1220 (512 MB) to a Model 1225 (1 GB).UPC2079-2
Upgrade a Model 1225 (128 MB) to a Model 1225 (2 GB).UPC2087-2
Upgrade a Model 1225 (256 MB) to a Model 1225 (2 GB).UPC2088-2
Upgrade a Model 1225 (384 MB) to a Model 1225 (2 GB).UPC2089-2
Upgrade a Model 1225 (512 MB) to a Model 1225 (2 GB).UPC2090-2
6.2 Memory Upgrade Kits
The following table lists the marketing IDs of the memory upgrade kits.
Description
Marketing
ID
M713 memory module (512-MB).UPM512-1
Model 1215 upgrade (1 GB to 1.5 GB). Add one M713 memory module to two existing M713
memory modules.
UPM7523

Model 1215 upgrade (1 GB to 2 GB). Add two M713 memory modules to two existing M713
memory modules.
UPM7524
Model 1215 upgrade (1.5 GB to 2 GB). Add one M713 memory module to three existing M713
memory modules.
UPM7534
Model 625/1225/1245 upgrade (1 GB to 1.5 GB). Add one M713 memory module to two existing
M713 memory modules.
UPM7567
Model 625/1225 upgrade (1 GB to 2 GB). Add two M713 memory modules to two existing M713
memory modules.
UPM7568
Model 625/1225 upgrade (1.5 GB to 2 GB). Add one M713 memory module to three existing M713
memory modules.
UPM7578
Model 1215 upgrade. Replace one existing M702 memory module (128 MB) with two M713
memory modules (1 GB).
UPM7412-1
Model 1215 upgrade. Replace two existing M702 memory modules (256 MB) with two M713
memory modules (1 GB).
UPM7422
Model 1215 upgrade. Replace three existing M702 memory modules (384 MB) with two M713
memory modules (1 GB).
UPM7432
Model 1215 upgrade. Replace four existing M702 memory modules (512 MB) with two M713
memory modules (1 GB).
UPM7422
Model 625/1225/1245 upgrade. Replace one existing M702 memory module (128 MB) with two
M713 memory modules (1 GB).
UPM7456-1
Model 625/1225/1245 upgrade. Replace two existing M702 memory modules (256 MB) with two
M713 memory modules (1 GB).
UPM7466
Model 625/1225/1245 upgrade. Replace three existing M702 memory modules (384 MB) with two
M713 memory modules (1 GB).
UPM7576
Model 625/1225/1245 upgrade. Replace four existing M702 memory modules (512 MB) with two
M713 memory modules (1 GB).
UPM7486
7. Related Documentation
The following table lists related documentation written by Customer Service Documentation that is available
worldwide to Stratus employees via the Customer Service Documentation home page on the Stratus internal web
page. The manuals with order numbers are in PostScript format or can be ordered from the copy center. The other
manual is in HTML format on the web.
Order NumberDocument
HM058Continuum 600/1200 Series Maintenance Guide
HI058Continuum 600/1200 Series Installation Guide
HU058Unpacking Instructions for Continuum 600/1200 Series Cabinets
K470 Supplement to Continuum 600/1200 Series Maintenance Guide
8. Part Numbers
The following tables list FRUs and CRUs contained in Continuum 600/1200 Series systems.

8.1 CEC Boards/Subassemblies
Part Number FRU/CRU Description
AA-G73100
AA-G73120
CRU
Uni 72 MHz, 128 MB (uses 128-MB memory module)
Sub model 00
Sub model 20
AA-G73200
AA-G73220
CRU
Uni 72 MHz, 256 MB (uses 128-MB memory modules)
Sub model 00
Sub model 20
AA-G73300
AA-G73320
CRU
Uni 72 MHz, 384 MB (uses 128-MB memory modules)
Sub model 00
Sub model 20
AA-G73400
AA-G73420
CRU
Uni 72 MHz, 512 MB (uses 128-MB memory modules)
Sub model 00
Sub model 20
AA-G73500
AA-G73520
CRU
Twin 72 MHz, 128 MB (uses 128-MB memory module)
Sub model 00
Sub model 20
AA-G73600
AA-G73620
CRU
Twin 72 MHz, 256 MB (uses 128-MB memory modules)
Sub model 00
Sub model 20
AA-G73700
AA-G73720
CRU
Twin 72 MHz, 384 MB (uses 128-MB memory modules)
Sub model 00
Sub model 20
AA-G73800
AA-G73820
CRU
Twin 72 MHz, 512 MB (uses 128-MB memory modules)
Sub model 00
Sub model 20
AA-G74500
AA-G74520
CRU
Twin 96 MHz, 128 MB (uses 128-MB memory module)
Sub model 00
Sub model 20
AA-G74600
AA-G74620
CRU
Twin 96 MHz, 256 MB (uses 128-MB memory modules)
Sub model 00
Sub model 20
AA-G74700
AA-G74720
CRU
Twin 96 MHz, 384 MB (uses 128-MB memory modules)
Sub model 00
Sub model 20
AA-G74800
AA-G74820
CRU
Twin 96 MHz, 512 MB (uses 128-MB memory modules)
Sub model 00
Sub model 20
AA-G75120CRUUni 96 MHz, 512 MB (uses 512-MB memory module)
AA-G75220CRUUni 96 MHz, 1 GB (uses 512-MB memory modules)
AA-G75320CRUUni 96 MHz, 1.5 GB (uses 512-MB memory modules)
AA-G75420CRUUni 96 MHz, 2 GB (uses 512-MB memory modules)
AA-G75520CRUTwin 96 MHz, 512 MB (uses 512-MB memory module)

AA-G75620CRUTwin 96 MHz, 1 GB (uses 512-MB memory modules)
AA-G75720CRUTwin 96 MHz, 1.5 GB (uses 512-MB memory modules)
AA-G75820CRUTwin 96 MHz, 2 GB (uses 512-MB memory modules)
AA-K45000CRUSCSI-ENET controller
AA-K45100FRUSCSI-ENET score card
AA-K60000CRUIO controller
AA-K60100FRUIO score card
AA-M70200FRUM702 memory module (128-MB)
AA-M71300FRUM713 memory module (512-MB)
MA-000305CRUCEC cardcage filler panel
AA-E58200FRU6-slot NFT clock card
AA-E59300CRUConsole controller
AA-P20000CRUBackplane power supply
AW-B10102-25CRURS-232 async. full modem cable
AW-B15200-25CRURS-232 async. null modem cable
JD-25PLG-07CRUCable gender adapter (25 pin M/M)
AW-000865FRUCDC: ADU/ARU cable 9F
AW-000783-08
FRUCDC: pwr. control A cable (50-pin)
AW-000785-08
FRUCDC: pwr. control B cable (37-pin)
AW-000857-07FRUCDC: RS-485 cable 78M
AW-000858-08FRUCDC: RS-485 cable 78F
AW-000862-06FRUCDC: IOA chassis cable 25F
AW-000809-10/35/75CRUENET cable - K450 SCSI-ENET controller
AW-000911-10/20/35CRUENET cable - K460 SCSI-ENET controller
AW-000789-02
FRUSCSI daisy chain cable
AW-000794-05/18FRUIO controller cable
8.2 Cabinets
Part NumberFRU/CRUDescription
AA-E64100FRUCEC backplane
AA-E75000
FRU
IO backplane
AA-E59600FRUPower controller backplane
AA-E60084CRUAir mover assembly
AA-E59500FRUAir mover backplane

MA-000252CRUAir filter (DC cabinet)
AA-E59000
FRUCDC/fan control board
AA-E59900FRUAlarm display panel
AA-E76000FRUTerminator maintenance bus
MA-000253FRU1U (1.75") air distribution panel
MA-000254FRU
3U (5.25") air distribution panel
8.3 Peripherals
Part NumberFRU/CRUDescription
AA-E57100FRU
Disk/tape (SCSI) backplane
AA-E57600
FRU
SCSI terminator (disk/tape enclosure)
AA-E60083CRUDisk/tape power supply
AA-E60086FRUDisk/tape chassis (primary)
AA-E60104FRUDisk/tape chassis (secondary)
AA-D70100CRUD701 disk drive (1 GB, 5400 rpm, 3 1/2")
AA-D70200CRUD702 disk drive (2 GB, 5400 rpm, 3 1/2")
AA-D70300CRUD703 disk drive (1 GB, 7200 rpm, 3 1/2")
AA-D70400CRUD704 disk drive (2 GB, 7200 rpm, 3 1/2")
AA-D70500CRUD705 disk drive (4 GB, 7200 rpm, 3 1/2")
AA-T70100CRU4-mm DAT II tape drive
AA-T70200CRUDAT tape drive with autoloader
AA-T70300
CRU525 MB cartridge tape drive
AA-T20400FRU
6250 BPI 1/2" SCSI tape drive
AA-T20410FRU
6250 BPI tape drive (table top)
AX-T20001FRU
T204 terminator
AW-000792-04/10/35FRU
SCSI cable (SCSI-ENET controller to primary disk/tape enclosure)
AW-000793-05/10/35/60
FRUSCSI cable (primary disk/tape enclosure to secondary enclosure)
AA-E51801
FRUSCSI cable (primary disk/tape enclosure to T403 tape drive) - 10'
AA-E51802
FRU
SCSI cable (primary disk/tape enclosure to T403 tape drive) - 20'
AA-E51803FRUSCSI cable (primary disk/tape enclosure to T403 tape drive) - 30'

AA-E51901FRU
SCSI cable (primary disk/tape enclosure to T204 tape drive) - 10'
AA-E51902FRUSCSI cable (primary disk/tape enclosure to T204 tape drive) - 20'
AA-E51903FRUSCSI cable (primary disk/tape enclosure to T204 tape drive) - 30'
AA-E60107CRUDisk/tape filler panel
AA-C41900CRUC419 modem*
AA-U20100Channel interface unit (CIU)
AW-000844-20
Cable (CIU to K113-01) (20')
AA-U25000Remote I/O (RIO)
AK-000305RIO simplex cable kit
AK-000307RIO duplex cable kit
AA-L30610FRUBand printer (600 lpm, 110 volt)
AA-L30620FRUBand printer (600 lpm, 220 volt)
* Replaced C319 modem (7/25/95).
8.4 Power Subsystems
Part NumberFRU/CRUDescription
AA-P20600CRUPower supply unit (PSU)
AA-P21000CRUBattery fuse unit
AA-P22300CRUBattery string
AA-P22700CRUFiber optic cable (10")
AA-P25100CRUFiber optic cable (197")
AW-000759-25
CRUAC power cable (domestic)
AW-000798CRUAC power cable (international)
AA-P21400CRUAC power controller (30A)
AA-P24300FRUBattery drawer slide pair
AA-P20400CRU
Power control unit (PCU)
AA-E60108CRU
DC power controller (250A)
AA-P22400CRU
Air filter (front)
AA-P22500CRUAir filter (rear)
AA-E60097FRU
C/DC power system (3600W)
AW-000405-15
AW-000405-25
FRUDC power input cable (A)
AW-000422-15

AW-000422-15
AW-000422-25
FRU
DC power input cable (B)
AA-P25000
FRUACPC filler panel
8.5 IOA Subsystem
Part NumberFRU/CRUDescription
AA-K10120CRUMulitcomm line adapter
AA-K10210CRUUnvrsl. line adapter - RS232/422
AA-K10410CRUEthernet line adapter
AA-K10810CRUTerminator
AA-K10900CRUUnvrsl. line adapter - RS232/423
AA-K11000CRUIBM printer line adapter
AA-K11200CRUUnvrsl. line adapter - RS232/V.35
AA-K11300CRUChannel attach line adapter
AA-K11400CRUX.21 line adapter
AA-K11500
CRU
Token ring line adapter
AA-K11800
CRU
16-port async line adapter
AA-K12000CRUDataKit line adapter
AA-K12400CRUT1/ISDN primary rate adapter
AA-K12500CRUISDN basic rate adapter
AA-K12700CRUNEC printer adapter
AA-K13200CRUDifferential SCSI adapter
AA-U30000CRUNEC Chameleon adapter
AA-E57800FRUIOA logic backplane (16-slot)
AA-E58600
FRU
IOA power backplane
AA-E60098
FRUK601 IOA chassis (11 slots)
AA-E60087
FRUK602 IOA chassis (16 slots)
A-E63300FRUK603 IOA chassis - Front (16 slots)
AA-E63400FRUK604 IOA chassis - Rear (16 slots)
AA-P20300CRUIOA chassis power supply