Converters.TV 963 User manual

23 Inch LCD WVA VGA LCD
- ID#963
Operation Manual

Introduction
This monitor is an open frame LCD Panel monitor. It features the VESA
plug & play system which allows the monitor to automatically a just itself
to match the frequency of the user's evice.
Feature
•High brightness.
•Fast response time.
•Power saver.
•Low electromagnetic wave an power saver.
•Safety certifications.
Power Saver
•The power control system is installe insi e the LCD monitor.
•If the monitor has not been use for a certain perio of time, the
system will turn the monitor to low voltage mo e to save power. Any
button press will return the monitor to original state.
•Your input evice e.g. your computer controls the power saver mo e.
You can a just these settings via your computer
•The LCD monitor is compatible with EPA Energy Star an N Tek if
use with a VESA DPMS computer.
•To save power, turn off the power of the LCD monitor when it is not
in use.
Plug and Play
•The VESA plug an play function eliminates the complicate an
time-consuming installation process.
•As this is a plug an play monitor. Your computer system can easily
i entify an automatically a just the monitor.
•The LCD monitor uses Display Data Channel (DDC) to sen Exten e
Display I entification Data (EDID) to the computer system, so the
computer system can be set to monitor auto a just.

Setting up your
LCD monitor •Choose a position where the reflection of the light is minimal an
away from a win ow for maximizing the quality of the screen image.
•It is important to keep 30cm between the LCD monitor to minimize
eye strain.
•Position the LCD monitor slightly above your horizontal vision as you
are sitting.
•Tilt either forwar or backwar for the most comfortable angle to view
the monitor. This LCD monitor supports connection to a computer or a
work station.
Screen
Adju tment
To enter a just mo e, please refer to the OSD control.
•Turn the computer an LCD monitor on.
•Press “Auto” button to start auto a just.
•This will start the auto a just process. This will take approximately 10
secon s. You may notice the image changing an occasionally
flashing (this is normal).
•Your LCD monitor provi es a self testing function, through which you
can check whether the LCD monitor functions are working properly.
•If your LCD monitor is properly connecte , but there is no image
showing an the in icator lights up in orange, please follow the below
steps:
•Shut own the computer an the LCD monitor.
•Unplug the signal connector from the back of the computer.
•Turn the LCD monitor on.
•If the image connector is isconnecte or amage , a “No signal” sign
will pop up on the monitor.
•Turn off the LCD monitor an reconnect the signal cable, an then
turn the computer an LCD monitor on.
•If the LED of the LCD monitor is an orange colour after completing
the steps above, please check your VGA car an computer system.
Your monitor shoul be operating properly.

OSD Control
Thanks to the user-frien ly esign of OSD (On Screen Display), you can a just
your monitor by the keypa s in the front of the monitor.
1. Power Switch Power On/Off.
2. LED Power In icator
Green = normal
Re = power saving
Off = power off.
3. Menu Automatically optimize positions, phase
an clock when OSD is not shown.
4. + This control is use for selection or
a justment when OSD is show.
5. - This control is use for a justment
when OSD is shown.
6. Auto/E c Enter OSD access sub-menu an
selection.
VGA Signal
Connector
Pin 1 Analog re input.
Pin 2 Analog green input.
Pin 3 Analog blue input.
Pin 4 Groun .
Pin 5 Digital groun .
Pin 6 Analog re groun .
Pin 7 Analog green groun .
Pin 8 Analog blue groun .
Pin 9 Groun .
Pin 10 Sync groun .
Pin 11 Groun .
Pin 12 SDA (DDC Data).
Pin 13 H. Sync or H + V Sync.
Pin 14 V. sync.
Pin 15 SCL (DDC CLK).

DVI
Signal Connector
PinSignal Pin Signal Pin Signal
1 TMDS Data 2- 9 TMDS Data1- 17 TMDS Data0-
2 TMDS Data2+ 10 TMDS Data1+ 18 TMDS Data0+
3
TMDS Data2/4
Shield
11
TMDS Data1/3
Shield
19
TMDS Data0/5
Shield
4 TMDS Data4- 12 TMDS Data3- 20 TMDS Data5-
5 TMDS Data4+ 13 TMDS Data3+ 21 TMDS Data5+
6 DDC Clock 14 +5V Power 22
TMDS Clock
Shield
7 DDC Data 15 Grou d(+5V) 23 TMDS Clock+
8 No Co ectio 16 Hot Plug Detect 24 TMDS Clock-
Operate Explanation
Your LCD has been adjusted to its optimal status before shipment. You
can also adjust the image in accordance with the following illustrations
and steps.
* Press the "Menu" button to start the OSD feature.
Click the "+" or "-" button to select the function to be adjusted. Click the "Select"
button to access into the function to be adjusted.
Click the "+" or "-" button to change the current setting of the function.
To e it the OSD menu or go back to the previous action by clicking the "MENU"
button. It will save the change automatically.
To repeat above steps for changing the setting of other functions. On OSD is not
shown , "select" key is video source select Hot key.

Note
The OSD isappears several secon s after you stop pressing the buttons
while performing an a justment.
Any changes are automatically save in the memory when the OSD
isappears. Turning off the power shoul be avoi e while using the
menu.
A justments for clock, phase an positions are save for each signal
timing. Except for these a justments, all other a justments have only
one setting which applies to all signal timings.
Adju ting the
Image
•Press the menu button to start the OSD feature.
•Click the “Up” or “Down” button to select the function to be a juste .
•Click the “Menu” button to access into the function to be a juste .
•Click the “Up” or “Down” button to change the current setting of the
function selecte .
•To exit the OSD menu or go back to a previous menu click the
“Auto/Esc” button. Upon exiting the menu your changes will
automatically save .
•If after pressing the menu button, the OSD button will isappear, if no
a itional buttons are presse for several secon s. If this occurs, any
a justments ma e, will still be automatically save .
•Due to the automatic save feature, turning off the power is unwise
while navigating the menu.

Screen Adju tment
Primary Directory Secondary Directory Description
Colour Contrast
Brightness
Colour A just
Colour Temp
Back
Adjust the contrast of the image.
Adjust the brightness of the screen.
Adjust the color of the image.
Select the colour Temp. you want.
R e t u r n t o m a i n m e n u .
Image Setting Clock
Phase
Sharpness
Timing Mo e
Back
Adjust the clock pulse of the image.
Adjust the focus of the image.
Adjust the picture sharpness of the image
1024, 1280, 1366 Mode select
Back to main menu
Position H. Position
V. Position
Back
Move the image left and right on the screen
Move the image up and down on the screen
Back to main menu
OSD Menu OSD H. Pos
OSD V. Pos
OSD Timer
Back
Move OSD display position to any position
Move OSD display position to any position
A just OSD isplay time setting
Back to main menu
Language Language Select the Language you want
Misc Select source
Reset
Back
Analog, Digital signal input
Restore to factory settings
Back to main menu
Exit Exit OSD menu

Front View
A. 513mm E. 91.5mm
B. 291mm F. 297mm
C. 563mm
D. 337mm

PC Support Timing
Item Resolution H Freq.(kHz) Freq.(Hz) Not
1 604x436@57 26.445 57.386 EGA
2 754x353@61 24.822 59.812 EGA
3 750x365@57 24.408 57.566 EGA
4 680x350@60 23.196 59.477 EGA
5 620x256@50 15.613 50.365 CGA
6 650x215@61 16.013 61.118 CGA
7 650x215@62 16.304 62.229 CGA
8 640x215@63 16.606 63.382 CGA
9 630x215@64 16.800 64.122 CGA
10 640x215@53 15.750 53.030 CGA
11 680x215@57 15.104 57.649 CGA
12 640x400@70 31.469 70.087 GA
13 640x480@60 31.469 59.940 ESA
14 640x480@66 35.000 66.667 MAC
15 640x480@72 37.861 72.809 ESA
16 640x480@75 37.500 75.000 ESA
17 720x400@70 31.469 70.087 TEXT
18 800x600@56 35.156 56.250 ESA
19 800x600@60 37.879 60.317 ESA
20 800x600@72 48.077 72.188 ESA
21 800x600@75 46.875 75.000 ESA
22 832x624@75 49.107 75.087 MAC
23 1024x768@60 48.363 60.004 ESA
24 1024x768@70 56.476 70.069 ESA
25 1024x768@75 60.023 75.029 ESA
26 1024x768@75 60.241 75.020 MAC
27 1280x768@60 47.776 60.004 ESA
28 1280x768@75 60.289 75.000 ESA
29 1366x768@60 47.720 60.004
30 1366x768@75 60.288 75.000

Specification
Specification for thi Model
Model Selection Guide VGA + DVI
Screen Size 23"
Pixel Pitch(mm) 0.372 x 0.372
Blacklight CCFL x 6
Cell Type APVA
Re pon e 16ms
Input Mode WXGA
Video Frequency Horizontal 30 ~ 60KHZ
Video Frequency Vertical 48 ~ 75Hz
Colour 16.7M Colors
A pect Ratio 16:9
Horizontal Viewing Angle 178 Degrees
Horizontal Viewing Angle 178 Degrees
Max Re olution 1366 x 768
Bandwidth 90MHz Dot Clock
Contra t Ratio 800:1 Typ
Brightne 450 Typ 450 c /m2
Di play Size Horizontal 508.125
Di play Size Vertical 285.696
Power AC Power(100 ~ 240VAC)
Power Con umption 80W Max
Management Vesa-Dpms 80W Max Power own
mo e </=3 Watts
Function Key 5
Input Signal 0.7Vpp Analog75 Ohm
Sync TTL Level Seperate, Composite
Window Compatability Win owsXP/2000
PC Interface Analog Interface
Signal Cable Stan ar VGA cable .
Operating Temperature 0 egrees ~ 40 Degrees
Humidity 10 ~ 85%