Converters.TV 15001 User manual

15 inch SVGA
LCD Monitor ID#15001
Operation Manual

Introduction
This is a 15 inch LCD SVGA input monitor for arcade machines and CNC
machinery retrofits. It features the VESA p ug & p ay system which
a ows the monitor to automatica y adjust itse f to the match the
frequency of the user's device.
Features •High brightness.
•Fast response time.
•Power saver.
•Low e ectromagnetic wave and power saver.
•Safety certifications.
Po er Saver
•The power contro system is insta ed inside the LCD monitor.
•If the monitor has not been used for a certain period of time, the
system wi turn the monitor to ow vo tage mode to save power. Any
button press wi return the monitor to origina state.
•Your input device e.g. your computer contro s the power saver mode.
You can adjust these settings via your computer
•The LCD monitor is compatib e with EPA Energy Star and N Tek if
used with a VESA DPMS computer.
•To save power, turn off the power of the LCD monitor when it is not
in use.
Plug and Play
•The VESA p ug and p ay function e iminates the comp icated and
time-consuming insta ation process.
•As this is a p ug and p ay monitor. Your computer system can easi y
identify and automatica y adjust the monitor.
•The LCD monitor uses Disp ay Data Channe (DDC) to send Extended
Disp ay Identification Data (EDID) to the computer system, so the
computer system can be set to monitor auto adjust.

Setting up your
LCD monitor
Screen Adjustment
To enter adjust mode, p ease refer to the OSD contro .
•Turn the computer and LCD monitor on.
•Press “Auto” button to start auto adjust.
•This wi start the auto adjust process. This wi take approximate y 10
seconds. You may notice the image changing and occasiona y
f ashing (this is norma ).
•Your LCD monitor provides a se f testing function, through which you
can check whether the LCD monitor functions are working proper y.
•If your LCD monitor is proper y connected, but there is no image
showing and the indicator ights up in orange, p ease fo ow the be ow
steps:
•Shutdown the computer and the LCD monitor.
•Unp ug the signa connector from the back of the computer.
•Turn the LCD monitor on.
•If the image connector is disconnected or damaged, a “No signa
input” sign wi pop up on the monitor.
•Turn off the LCD monitor and reconnect the signa cab e, and then
turn the computer and LCD monitor on.
•If the LED of the LCD monitor is an orange co our after comp eting
the steps above, p ease check your VGA card and computer system.
Your monitor shou d be operating proper y.
•If the “out of range” error pops up on the monitor, the input frequency
is outside of the specified range and wi not disp ay an image. The
correct frequency wi need to be entered and then restart the monitor.

Panel Controls
1. LED Green : Power On + Signa Source
Detected
Red : Standby or Signa Source Not
Detected
Off : Power off
2. Po er Power On/Off.
3. Up/+ This button is used for positive
adjustment when OSD is Disp ayed
4. Do n/- This button is used for negative
adjustment when OSD is Disp ayed
5. Menu This button is used to disp ay the ON
Screen Disp ay (OSD) menu and se ect
settings and parameters.
6. Auto Automatica y optimize positions, phase
and c ock when OSD is not shown.
Adjusting the

Image •Press the menu button to start the OSD feature.
•C ick the “Up” or “Down” button to se ect the function to be adjusted.
•C ick the “Menu” button to access into the function to be adjusted.
•C ick the “Up” or “Down” button to change the current setting of the
function se ected.
•To exit the OSD menu or go back to a previous menu c ick the
“Auto/Esc” button. Upon exiting the menu any changes wi be
automatica y saved.
•The OSD menu wi disappear if no buttons are pressed for severa
seconds. OSD disp ay time is adjustab e to suit needs
•Due to the automatic save feature, turning off the power is unwise
whi e navigating the menu.
Please Note: Due to the advanced nature of this pane . Adjustments to
c ock, phase and image positioning are saved on y for the signa timing
you are current y using. Meaning if your input is CGA 640 x 215 @60Hz,
and you adjust the c ock setting. This wi on y affect this timing.
So when your change input to VGA 640 x 480 @60Hz for examp e the c ock wi
be at its defau t (or ast memory saved setting). This is to a ow the user to get a
picture perfect for every input he requires and avoid redoing settings each time
the input is changed. Except for these adjustments, c ock, phase and image
positioning, a other adjustments are universa for examp e changing the
brightness setting wi change the brightness setting for a inputs and timings.
To he p the User remember; a settings that on y affect the timing you’re
current y using are co oured pink and the universa settings are co oured white.
Detects and
disp ays current
input setting

OSD Menu
Options
Menu
Auto Setup Automatica y optimize positions, phase and
c ock
Brightness Brightness Adjust Screen Brightness
Recall Restore to Defau t
Return Exit menu
Contrast Adjust the Screen Contrast
Display Adjust H Position Adjust the Horizonta
Positioning
V Position Adjust the Vertica Positioning
V Size Adjust the Vertica Screen Size
Clock Adjusts horizonta a ignment
Phase Adjusts horizonta a ignment
Quality Adjusts the qua ity of the
image
Mode Selection Defau t Ana og VGA in
Recall Restore to Defau t
Return Exit menu
Colour Temperature 9300k Set up the co our temp. to be
9300 K white co our.
7500k Set up the co our temp. to be
7500 K white co our.
6500k Set up the co our temp. to be
6500 K white co our.
Auto Gain Auto Co our adjustment
Red Adjust the Red co our
va ues
Green Adjust the Green co our
va ues
Blue Adjust the B ue co our
va ues
Return Exit menu
Language Choose anguage from Eng ish, French, Ita ian,
Chinese, Japanese

OSD Display OSD H-Pos Position the OSD menu
horizonta y on screen
OSD V-Pos Position the OSD menu
vertica y on screen
OSD Timer Set the OSD menu on screen
disp ay time
OSD
Transparency
Set the OSD menu
Transparency
OSD Direction Set the direction of the OSD
menu : Norma , Mirror, Left,
Right, Up or Down
Display Logo Disp ay Logo
Recall Restore to Defau t
Return Exit Menu
VGA/DVI Analog Input Se ects VGA input
Digital Input Unavai ab e
Return Exit Menu
Audio Audio Mute Audio
Volume Adjust the vo ume
Recall Restore to defau t
Return Exit menu
Read me Quick start Guide
Recall Restore to defau t
Exit Restore to defau t
Warning: Phase and Clock Settings shouldn’t be touched unless you know
what you’re doing. Altering these values can make the image unwatchable on
the screen

Support CGA/EGA/VGA Timings
Type H. Frequency.
(kHz)
V. Frequency
(Hz)
Resolution
CGA 15.4 58.8 640x198
CGA 15.1 57.6 640x215
CGA 15.7 60 640x215
CGA 16.0 61 640x215
CGA 16.3 62 640x215
CGA 16.6 63.4 640x215
CGA 16.800 64 640x215
CGA 15.6 50.3 640x265
CGA 18.4 50 640x350
VGA 31.469 70.087 640x400
VGA 31.469 59.940 640x480
VGA 35.000 66.667 640x480
VGA 37.861 72.809 640x480
VGA 37.500 75.000 640x480
SVGA 35.156 56.250 800x600
SVGA 37.879 60.317 800x600
SVGA 48.077 72.188 800x600
SVGA 46.875 75.000 800x600
XGA 48.363 60.004 1024x768
XGA 48.78 59.561 1024x768
XGA 56.476 70.069 1024x768
XGA 60.023 75.029 1024x768
SXGA 47.732 60.024 1280x768
SXGA 60.168 75.019 1280x768
SXGA 60.000 60.000 1280x960
SXGA 63.981 60.020 1280x1024
SXGA 79.976 75.025 1280x1024
Additional Timings
31.469 70.087 720x400
49.726 74,551 832x624
67.500 75.000 1152x864
68.681 75.062 1152x870
61.795 65.950 1152x900
71.809 76.149 1150x900
47.700 60.000 1360x768
55.935 59.887 1440x900
70.640 74.980 1440x900
Above is just a guide, many other frequencies are accepted

Connecting into Option 1 - Using VGA Input
Monitor
By using a standard VGA 15 pin computer cab e p ug and p ay or,
a ternative y you may cut the end of your cab e and wire direct y to the
output connector of the source equipment.
Pin 1 Ana og red input.
Pin 2 Ana og green input.
Pin 3 Ana og b ue input.
Pin 4 Ground.
Pin 5 Digita ground.
Pin 6 Ana og red ground.
Pin 7 Ana og green ground.
Pin 8 Ana og b ue ground.
Pin 9 Ground.
Pin 10 Sync ground.
Pin 11 Ground.
Pin 12 SDA (DDC Data).
Pin 13 H. Sync or H + V Sync.
Pin 14 V. sync.
Pin 15 SCL (DDC CLK).
Option 2 - RGB iring via Adapter PCB
The PCB interface board is designed to faci itate connection from o der sty e
CGA/EGA/VGA source equipment. The board a so a ows for adjustment of
incoming co our signa eve s and Impedance Matching se ection se ection for
'b ack ine' screen..
Using the supp ied 5 and 6 wire open ended cab es, signa formats of RGBH+V
(combined sync) or RGBHV (separate sync) may be easi y connected.

P1 – RGBHV
separate/ or combined sync
P3 – RGBH+V
combined sync
Pin 1 – Red Pin 1 – Red
Pin 2 – Green Pin 2 – Green
Pin 3 – B ue Pin 3 – B ue
Pin 4 – Signa Earth Pin 4 – Signa Earth
Pin 5 – Horizonta /Combined
Sync
Pin 5 – Horizonta /Combined Sync
Pin 6 – Vertica Sync
About Our Adapter PCB and Further Adjustments
Our adapter PCB offers a number of adjustments via the fo owing contro s
-VR1 to VR3
Adjust to vary the eve of the individua output co our signa s to compensate
for over exposure/brightness of video image.
VR1 – Red | Adjusts co ours to reduce the
VR2 – Green | signa strength if image is
VR3 – B ue | over bright

Filter Jumpers
Set Jumpers as required to reduce effect of b ack ine artifacts
when ow reso ution mismatch becomes evident on LCD screen.
By setting to “ON” position, each co our can be fi tered as required.
.
C1 = Red Co our 1 |
C2 = Green Co our | To adjust for
C3 = Not used | Impedance
C4 = B ue co our | Matching of
C5 = Not used | interfaces
C6 = Red Co our 2 |
Front/Side Vie

Specifications
Specifications for this Model
Screen Size 15" TFT
Pixel Pitch(mm) 0.264 x 0.264
Blacklight 2xCCFL
Cell Type TN
Input Mode SVGA
Scan Frequency Horizontal 15 ~ 80KHZ
Scan Frequency Vertical 48 ~ 75Hz
Colours 16.7M Co ors
Aspect Ratio 5:4
Horizontal Vie ing Angle Fu range
Optimal Screen Resolution 1024 x 768
Band idth 130MHz Dot C ock
Contrast Ratio 500:1 Typ
Brightness 250cd/m2
Po er 100~240V 50/60Hz via 12VDC
1.2A adapter
Po er Consumption 13.35 Watts(Typ.)
Management Vesa-Dpms 42 watts Power down
mode </=3 Watts
Function Keys 5
PC Interface Ana og Interface
Signal Cable Standard VGA cab e w/15-pin
D-sub connector.
Or via VGA Inverter PCB
Operating Temperature 0 degrees ~ +50 Degrees
Humidity 10 ~ 85%
Overall Dimensions 325mm x 258mm x 44mm
Active Screen Area Dimension 310mm x230mm
Weight 2.450kg

Troubleshooting
Error Solution
No Po er Led Check Mains Power supp y input Vo tage
(100v or 240vAC) and connection
Check 12V DC at power supp y output
Check contro board for damage
No image Check cab es connected correct y from
source and into monitor inputs
Check correct orientation of signa wires;
H-sync and V-sync
Check for CCFL amp operation on rear of
cd pane , visua reference on y
Check power 'on' source and monitor
Image Alignment Adjust using “AUTO” button
Fine adjust using the OSD Menu
parameters according y for Horizonta and
Vertica position/size
Image Brightness/Contrast Adjust OSD Menu parameters for
Brightness and Contrast
Image colour Check RGB co our wires connected and
active
Adjust OSD Menu parameters for co our
temperature and co our intensity
Intermittent Image Ensure equipment is earthed and iso ated
from signa earths, Note: Iso ation (No
Earth) sometimes improves image
reception
Ensure open wire cab es are sheathed and
earthed against EFI (E ectromagnetic Fie d
Interference)
Check a cab e pins a igned and seated
correct y