Convoy Tech Performance M7104RF Quick start guide

Owner’s / Installaon Manual
Performance Series
M7104RF
LCD COLOR MONITOR
Convoy Technologies 3300 Irvine Ave., Suite 310 | Newport Beach, CA 92660 | Ph [phone]
Please read this manual thoroughly before operang the unit, and keep it for further reference.

Owner’s / Installaon Manual
Performance Series
M7104RF
PRECAUTIONS
Convoy Technologies 3300 Irvine Ave., Suite 310 | Newport Beach, CA 92660 | Ph [phone]
1. Precauons
Storage and keeping
Do not expose the monitor to excessive heat or cold. The storage temperature of this device is -30 ~+75 C, and the oper
ang temperature is -20 ~+60 C. The Humidity is Rh90%.
Never use this device near a bathtub, wash basin, kitchen, damp basement, swimming pool or similar place.
Never use this device in environments with excessive moisture, dust or smoke.
Avoid dropping or striking this device.
Never puncture, scratch or use abrasive cleaning materials on this device.
The monitor is not designed to be waterproof.
Operang Precauons
Make sure all cables are connected properly observe polarity. Improer cable connecons may damage the monitor. Re
move the power cable connecons when you do not intend to use the unit.

1. Precauons
Maintenance
1. Remove all the cable connecons from the monitor before cleaning the unit.
2. Use a mild household detergent and clean the unit with a slightly damp, so cloth. Never use strong solvents such as thin-
ner or benzene, as they might damage the nish of the device.
This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s en-
closure that may be of sucient magnitude to constute risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operang and maintenance (servcing) instruc-
ons in the literature accompanying the appliance.
This symbol is intended to alert the user not to waste electrical and electronic equipment.
CAUTION
You are cauoned that any changes or modicaons not expressly approved in this manual could void your warran-
tee and necessitate expensive repairs.
Declaraon of conformity
This device complies with Part 15 of the FCC Rules. Operaon is subject to the following two condi-
ons: This device may not cause harmful interference. This device must accept any interference
received, including interference that may cause under desired operaon.
Owner’s / Installaon Manual
Performance Series
M7104RF
PRECAUTIONS
Convoy Technologies 3300 Irvine Ave., Suite 310 | Newport Beach, CA 92660 | Ph [phone]

Owner’s / Installaon Manual
Performance Series
M7104RF
Mounng the Monitor
Convoy Technologies 3300 Irvine Ave., Suite 310 | Newport Beach, CA 92660 | Ph [phone]
1) Select a locaon allowing 2” space between monitor and walls, cabinets, or other objects to allow adequate air circulaon
around it. Avoid enclosed spaces, areas with excessive vibraon or subject it to severe impacts.
2) Never use this device in environments with excessive moisture, dust or smoke. Do not place cables where they may be
pinched or stepped on. Monitor is not designed to be waterproof.
3) The device may be powered by a 12 or 24 volt automove baery or vehicle electrical system.
4) Make sure all cables are connected properly, observe polarity. Improper cable connecons may damage the monitor. Remove
the power cable connecons when you do not intend to use the unit.
Installaon Notes: Trigger wire funcon
• All 4 Camera connecons have a trigger wire which can be acvated with 12VDC. When the trigger wire is acvated, the
monitor automacally switches to view THAT Camera. When voltage is removed from the trigger wire, monitor returns to
previous view.
• If the monitor is o, when the trigger wire is acvated, the monitor will turn on to show THAT Camera. This safety feature is
parcularly useful for night driving, as the monitor light can be distracng to the operator.
• CT-M7104RF has just one RF receiver, so it will only show one camera at a me. It can pair with and remember up to 4 cam-
eras. Pairing memory is not volale when power is disconnected, the cameras stay paired.
M7104RF Harness:
• Red and Black—Power (12-24VDC) and Ground
• Green—Trigger Wire for Channel 1
• White—Trigger Wire for Channel 2
• Yellow—Trigger Wire for Channel 3
• Blue—Trigger Wire for Channel 4

Owner’s / Installaon Manual
M7104RF Operaon
Convoy Technologies 3300 Irvine Ave., Suite 310 | Newport Beach, CA 92660 | Ph [phone]
Pressing MENU shows the rst MENU screen. There are 5, each press of MENU selects the next screen. To adjust a feature, rst
select it by hing CAM buon, then use—or + to change.
• -/+ buons adjust Volume. Aer pressing MENU, they will change a feature that is highlit, hit CAM to select that feature, then
either -/+ to adjust the feature shown. MENU will select the next menu screen. Menu will me out aer 10sec without a
buon press. You can also connue to hit MENU to exit.
• Ch Select in the OPTIONS menu selects the number of cameras you want displayed, 1,2,3,4.
• Pairing Cameras: hit CAM to select Channel. Push and hold MODE 3sec and release to start pairing mode. 50sec countdown
starts. Go to camera to pair, push and hold camera pairing buon 6sec and release. You will see SAVE DATA on monitor when
pairing is successful. Hit CAM to select next channel and repeat steps above ll you have paired all cameras.
• Ch Delay menu allows you to select the me to view each camera when using Channel scrolling feature. Once cameras are
paired, push and hold CAM 4sec and release. Monitor will display each camera channel the preset amount of me.
• Ch Back menu allows you to select the me delay the monitor stays on a triggered camera. (if you use a turn indicator wire to
trigger a side camera, that voltage switches on and o. Increasing Ch Back delay, the picture from that camera will stay on
instead of ashing on and o with the trigger voltage)
(1) - buon – Vol Down, or adjusng Down
(2) + buon – Vol Up, or adjusng UP
(3) MENU – Access menu: Picture, Audio, Opons, Ch Delay, Back Delay
(4) CAM – Switches camera channel, or select an opon in MENU.
(5) MODE – Enters Monitor into pairing mode when held 3 seconds
(6) POWER – Turns monitor On and O.
(7) Power indicactor Light.
(8) Loudspeaker
Pressing MENU will reveal the menu pages (there are 5). Use VIDEO SELECT and MODE SELECT buons to
select a feature, and ↔buons to adjust.
• ↔buons adjust Volume. Aer pressing MENU, they adjust the feature shown. Use VIDEO SELECT (UP)
AND MODE SELECT (DOWN) buons to highlight the feature on a menu page.
Using the Remote Control

Owner’s / Installaon Manual
Replacing the Remote Baeries
Troubleshoong
Specicaons Warranty and Support Informaon
Convoy Technologies 3300 Irvine Ave., Suite 310 | Newport Beach, CA 92660 | Ph [phone]
7” TFT-LCD Color Monitor
Audio Output: 0.5 W
Power Supply: 12-24VDC
Power Consumpon: 4W Max,
0.33amps
Video Input: 4
Resoluon: 800x3 (RGB),
480
Contrast: 500:1
Brighness: 510cd/m²
Viewing Angle: 50°-U, 70°-D,
R/L 70°
Operang Temperature: -20°C—+50°C
Subject to the provisions described below, this CT product is protected for 1
year against defects in material and workmanship. Should a product fail to
perform as described above within the warranted period, it will be repaired or
replaced with the same or funconally equivalent product by CT. This warrant
does not apply if , in the judgement of CT, the product fails due to damage
from shipment, handling, storage, accident, abuse or misuse, or if it has been
used or maintained in a manner not conforming to product manual instruc-
ons, has been modied in any way. Repair by anyone other than CT or an ap-
proved agent will void this warranty. The maximum liability of CT under this
warranty is limited to the purchase price of the product covered by the warran-
ty. All defecve products should be returned to CT with shipping charges pre-
paid. CT will not accept collect shipments.
Symptom possible Causes/Soluons
No picture. No sound Improper connecon of automobile adapter. Use of un-authorized power supply. Power switch is on OFF posion
No picture Check whether locking cable is properly connected.
No sound Check whether locking cable is properly connected, or the sound volume is set too low
Dark picture Check whether brightness and contrast are adjusted correctly; Check whether the environments temperature is too low.
No color Adjust the color sengs.
Upside down or lateral
inverted picture Use the remote/ MENU-OPTION-ROTATION buon to set proper orientaon
No reversing funcon
(i.e. Picture) Check the wires (black/ red/ Green) that may be loose
Performance Series
M7104RF