CONWIN Helium / Hi-Float User manual

Helium / Hi-Float™ Adapter
Instruction Sheet
1Hold the balloon under the Helium/Hi-Float Adapter with
the silver outlet in the center of the
balloon.
2Press the pump to inject the Hi- Float into the body of the bal-
loon. Rub the balloon to evenly coat
the inside of the balloon with Hi-Float
– be sure not to get Hi-Float into the
neck of the balloon.
3Tap the foot pedal of the Duplicator 2 or Dual Sizer to
automatically inflate the balloon to
the perfect size.
4Pinch the neck of the balloon and remove it from the filling outlet.
Wipe off any excess Hi-Float from the
outlet.
Hi-Float™ Adapter - Set Up
1Firmly press-fit connect the Helium/Hi-Float Adapter on to
the outlet of the Hi-Float pump. The
Adapter has a locking ring that will
hold it in place.
Removing the Helium/Hi-Float™ Adapter
To release the Helium/Hi-Float Adapter from the Hi-
Float pump press the locking ring down with your finger
nails. This will release the Adapter and it will easily slide
off the pump. Be sure to depress the locking ring fully
before pulling the Adapter off the pump.
Maintenance Tips
•Always cover the tip of the Helium/Hi-Float Adapter with the red plastic Hi-
Float pump cap when the unit is not in use. This prevents Hi-Float from clogging
the Adapter. (Note, if you misplace the pump cap, a 5-inch or smaller balloon
stretched over the tip works well.)
• If Hi-Float clogs the Helium/Hi-Float Adapter remove the Adapter from the
pump and flush it with warm water. Warm water dissolves dried Hi-Float.
2Attach the helium line to the fill- ing outlet of a Duplicator 2 infla-
tor or Dual Split-Second Sizer. 3Set the Duplicator 2 or Dual
Sizer to the appropriate size set-
ting for 11-inch or larger balloons.
Note, if using a Dual Sizer, be sure to
set the inflator mode to operate from
one outlet – not both.
4Place the Hi-Float clip on the stem of the Hi-Float pump. (Clips
are included with the Hi-Float pump.)
See www.Hi-Float.com for Hi-Float
recommendations.
Hi-Float™ Adapter - Inflating Instructions

10292004
Conwin’sMasterpiece Series Videos
Service & Warranty
For assistance with service & repair
issues, or for warranty information,
please visit ConwinOnline.com,
or call [phone]
These exciting instructional videos
feature the industry's top balloon
artists sharing their secrets of the
trade on everything from the latest
decorating techniques to business
management and marketing skills.
Visit ConwinOnline.com to see our
complete line of educational videos.
Galleries
Projects
...and more!
Online
Visit www.ConwinOnline.com today!
Designs
Hi-Float™ Power Pump
Instruction Sheet
1Hold the balloon under the Helium/Hi-Float Adapter with
the silver outlet in the center of the
balloon.
2Press the button on the control box to activate the Power Pump. Hold
down button until the pump depresses
fully. (Consult Balloon Size Chart at right)
Rub the balloon to evenly coat the inside
with Hi-Float. Be sure not to get Hi-Float
into the neck of the balloon.
Balloon Size Chart
11-inch Balloons
press button 1 time.
14-inch Balloons
Press button 2 times.
16-inch Balloons
Press button 3 times.
3Tap the foot pedal of the Duplicator 2 or Dual Sizer to
automatically inflate the balloon to
the perfect size. Pinch the neck of the
balloon and remove it from the filling
outlet. Wipe off any excess Hi-Float
from the outlet.
• If the balloons are going to be
treated and immediately inflated use
the T-4-2 Adapter on a helium cylin-
der. Use a wrench to tighten the T-4-
2 Adapter to the helium cylinder. The
T-4-2 Adapter will enable two regula-
tors to work off one helium cylinder.
Hand-tighten the Power Pump regu-
lator and the Duplicator 2 or Dual
Sizer regulator to the T-4-2 Adapter.
• If you’re pre-treating balloons with
Hi-Float to be inflated at a later time,
nitrogen is a more economical gas to
use.
• Follow Hi-Float’s charts and recom-
mendations to use the appropriate
amount of Hi-Float in the balloon.
• Visit www.Hi-Float.com to learn
more about working with Hi-Float.
Hi-Float™ Power Pump - Set Up Tips
1Connect the Power Pump regulator to a nitrogen or helium cylinder. 2Place a large bottle of Ultra Hi-Float on the holder and
secure in place with the Velcro belt. 3Hook the wire loop under the
pump handle. Place the 11-inch
Hi-Float clip on the Hi-Float
pump (included with the Hi-
Float pump).
Follow the instructions on the reverse page to set-up the Helium/Hi-Float Adapter.
Hi-Float™ Power Pump - Operating Instructions
T-4-2 Adapter
If pre-treating balloons to be filled with
helium at a later time, skip step 3.