CoolPets 4KIT-S-PG User manual

WATER COOLED DOG HOUSE
PLEASE READ ALL INSTRUCTIONS CAREFULLY BEFORE AND DURING ASSEMBLY.
RETAIN THIS LEAFLET FOR FUTURE REFERENCE.
FEATURES
TOP & BOTTOM
COOLING
BLOCK
ASSEMBLY INSTRUCTIONS
Two side opening option shown.

2
KIT CONTENTS
THIS KIT CONTAINS QTY
Left Hand Wall (plain or with awning) 1
Right Hand Wall (with awning) 1
Cord (Black) 1 or 2
Girders 3
Bottom Cooling Block 1
Top Cooling Block 1
Back Wall 1
Front Wall 1
Corner Post Assembly (long) 3
Feet 3
Corner Post (shorter length) 1
Height Adjustor 1
Corner Post Screws (small) 8
Post Connectors 4
Roof Panels 2
Roof Caps 4
Roong Bolts 4
Roof Centre Alloy Strip 1
Water Tube Lengths
Standard Dog House (1500mm, 620mm, 250mm, 2x80mm, 115mm) 6
Large Dog House (1500mm, 705mm, 330mm, 2x80mm, 115mm) 6
90˚ Water Connector 3
Water Bowl 1
Spout 1
Hose Connector 1
Support Blocks Left Hand 2
Support Blocks Right Hand 1
Support Blocks Right Hand Short 1
Assembly Instruction Manual 1
Product Manual 1

3
PARTS LIST
Feet
Roof Bolts
Hose Connector
Height Adjustor
Roof Centre Alloy Strip
Post Connector
Roof Caps
Spout
90o Water Connector
Support Blocks Corner Posts Water Bowl

4
GETTING STARTED
Choose the location where the“CoolPets”Water Cooled Dog House will reside.
Ensure your garden hose can reach this location.
Your “CoolPets”Water Cooled Dog House is demountable, i.e. it can be
dis-assembled and re-assembled many times without damage to the parts.
Kit parts are designed to easily clip together with requirement for only a screw
driver on 8 screws. However, once assembled, the structure cannot be picked up
and re-located. Should this be desired, the Dog House has to be dis-assembled and
re-assembled in the new location.
It can, however, be dragged a short distance without coming apart.
Assembly is not complicated, provided the instructions are followed, however, it
is considerably easier if two people are present due to the size and weight of the
panels. Assembly requires approximately 45 minutes.
Fully enclosed footwear is recommended during assembly.
The dog bowl is designed to be axed to the ground, to ensure it cannot be moved
out of its position. However, it can be easily removed for cleaning purposes.
WARNING:
Strong water pressure will damage the cooling block – Please allow time for the
water to pass through the kennel slowly – It should take approximately 5 minutes
before the water starts to ow into the water bowl via the downpipe.

5
ASSEMBLY INSTRUCTIONS
1. Stand left hand and right hand walls
upright, facing each other with the
brackets on the inside, two at the
bottom end and one at top end.
(Refer Fig. 1)
2. Insert 2 girders into the bottom
brackets to secure side walls into place.
(Refer Fig. 1)
3. Attach 1500mm water tube to water
inlet in bottom cooling block and the
80mm tube to the water outlet.
(Refer Fig. 2)
4. Place bottom cooling block on top of
girders ensuring the water connectors
are on the underside and at the back of
the dog house. (Refer Fig. 3)
5. Slide corner post assemblies into
position. The short post should be on
the front right hand side of the Dog
House. Ensure the remaining posts are
positioned so that the top angles can be
aligned to the slope of the roof.
(Refer Fig. 4)
6. Attach support blocks to align with the
holes at the base of the corner posts
and fasten into place with 4 screws.
Ensure the short support block is at
front right hand side. Insert feet at
bottom of corner posts. Height adjustor
attaches to front right hand corner post.
(Refer Fig. 5)
Fig. 1
Fig. 3
Fig. 4
Fig. 5
Fig. 2
1500mm water tube
Underside of bottom
cooling block
80mm
water tube

6
ASSEMBLY INSTRUCTIONS CONT.
7. Fasten 4 screws into position at the
higher holes of corner posts.
(Refer Fig. 6)
8. Slide back and front wall panels into
position ensuring the two water tubes
from the bottom cooling block sit in the
cutouts on the back wall . (Refer Fig. 7)
9. Slide third girder between top brackets.
(Refer Fig. 8)
10. Attach 4 corner post connectors onto
top of four posts.
11. Lay top cooling block on top of girder
and fasten onto four corner post
connectors. (Refer Fig. 8)
12. Pass the remaining 80mm tube through
the pre-made hole in the top of the
back wall panel and attach to the water
inlet on the top cooling block. Using 90˚
connectors join the 620mm/705mm
water tube to the top and bottom
cooling block. (Refer Fig. 9)
13. Pass the 115mm water tube through
the pre-made hole on the right hand
side wall panel and connect to top
cooling block water outlet. (Refer Fig. 9)
14.
Attach spout to one end of the remaining
250mm/330mm water tube, then push
tube upwards through the semi-circle
bracket and connect other end of tube
to 90 ˚ water connector on the outside of
the right hand wall. (Refer Fig. 10)
Fig. 6
Fig. 7
Fig. 8
Fig. 9
620mm/705mm
water tube
Fig. 10
80mm
tube
Topside of top
cooling block
250mm/330mm
tube connects
to spout
115mm tube

7
15. Secure roof panels into place using the
plastic caps and bolts provided. Insert
aluminium extrusion into place on the
top ridge. (Refer Fig. 11 & 12).
NOTE:Alternatively, secure one roof
panel, then attach aluminium extrusion
to it before securing second roof panel,
if this is easier.
Your assembled dog house should look
like Fig. 13.
16. Finally, ax dog bowl into position.
(Refer Fig. 14)
You are now ready to test the water
cooling feature.
WARNING:
Strong water pressure will damage the
cooling block – Please allow time for
the water to pass through the kennel
slowly – It should take approximately
5 minutes before the water starts to ow
into the water bowl via the downpipe.
Fig. 11
Fig. 12
Fig. 14
IMPORTANT:
Correct Water Pressure
Fig. 13

Manufactured in China exclusively for CoolPets Pty Ltd. Designed and imported by CoolPets Pty Ltd.
USA and Australia Patents Filed
Visit our online store for more products and information
www.coolpets.com.au
Assembly Instructions for
#4KIT-S-PG, #5KIT-S-PG, #4KIT-L-PG