Coolzone CZ55509 User manual

INSTALLATION AND OPERATING INSTRUCTIONS
50cm Double Cavity Gas Cooker
CZ55509
The product may differ from the one illustrated but the installation and operation procedure remains the same

Contents
Introduction 3
Unpacking 3
Before installation 3
Location 4
Electricity supply 5
Safety chain anchors 5
Gas supply connection 6
Electrical connection 6
Levelling the cooker 6
Securing the safety chains 7
Preparation 7
Safety notes 8
Cooker controls 9
Using the hob 9
Using the grill 10
Using the oven 11
Care of the cooker 11
Cleaning the cooker 12
Changing the oven and grill lamps 13
Mains lead replacement 13
Plug replacement 13
For best cooking results 14
Troubleshooting guide 15
Safe oven disposal Back page
Customer Helpline Back page
Specification Back page

3
Introduction
Thank-you for choosing this quality appliance. It has been designed to provide trouble-free service provided
it is installed and maintained correctly.This cooker is for domestic use only.
Please read these instructions carefully before installing or using your appliance. It is advisable to keep
your purchase and installation receipts with these instructions in a safe place for future reference. Included
is some important safety information, guidelines and recommendations to enable you to safely use your
cooker.
This appliance has been tested and certified to meet all applicable UK electrical and gas safety standards.
This appliance must only be installed and repaired by a CORGI registered installer or authorised service
personnel. If it is not repaired properly you could be putting yourself and others in danger. It will also
invalidate the guarantee.
Prior to installation, ensure that the local distribution conditions (nature of the gas and gas pressure) and
the adjustment conditions are compatible.The factory set adjustment conditions for this appliance are
stated on the rating label.
If you have any questions or need assistance please telephone the Helpline on 0844 871 0011.
When contacting the Helpline please have model number to hand.The model number is shown on the data
label which is visible by opening the oven door.
Unpacking
Carefully remove all the packaging and lift out the cooker and accessories.
Open the oven and remove any tape or packing material used for transit.
Check the appliance for any damage. If it has been damaged do not use it and contact the retailer from
whom the appliance was bought.
Retain the packaging until the cooker has been installed, removing it from the area of installation and
keeping it out of the reach of children.
Dispose of all the packaging in accordance with your local authority guidelines as well as any old appliance
that is being replaced – see “Safe cooker disposal” section.
Before installation
Before any installation work can be carried out a number of requirements must be met.
Make sure that you or your installer are familiar with all the relevant building and fire regulation
requirements before choosing the location of your appliance.
This appliance must be installed in accordance with the instructions to validate the guarantee.
Refer to the “Location” section for minimum clearances and safe placement of your cooker.

4
Location
Position of the cooker
The position of the cooker should ensure free access to all controls.
Avoid installing the cooker next to a fridge, freezer or boiler.
Safety Requirements
This appliance must only be installed in an area with adequate ventilation.
Do not install the cooker on a window-door axis or any position where strong draughts are likely.
Ensure that the surrounding material is heat resistant and non-combustible.
The electricity supply must be routed near to the installation.
There must not be any plugs, wires or sockets in the wall directly above or behind the cooker top.
Clearance space
Certain minimum clearances must be allowed for when planning the unit’s location (Figure 1):
The cooker should be installed into a space at least 550mm wide.
There should be an open space above the hob to allow kitchen odours to disperse. A cooker hood may be
installed to either absorb or extract the odours.The distance between the hob and the hood must not be
less than 650mm (Figure 1).
Leave adequate clearance between the cooker hob top and adjoining vertical cupboards (no less than
150mm.)
Figure 1 - Minimum Clearances

5
Figure 2 - Fixing an anchor bracket
Electricity supply
A switched 3-pin plug socket with an earth contact, if one does not already exist, should be installed on the
wall behind the cooker (Figure 1).
WARNING:This appliance must be earthed. Connecting the cooker to a socket without an earth
contact may result in an electric shock
This installation must be carried out in accordance with current I.E.E wiring regulations and Building
Regulations (Part P).
The 3-pin socket should be close enough so that the appliance can be easily plugged in without stretching
the mains supply cable.
The mains supply cable must be routed away from hot surfaces.
The mains voltage must correspond exactly to that which is specified on the data plate.
If in any doubt consult a qualified electrician.
Safety chain anchors
In order to eliminate the risk of the cooker falling forward, two chains have been installed at the rear of the
cooker. Before use, these will need to be fastened securely to the wall behind the appliance with the
anchor brackets supplied. (Figure 2):
1. Decide on a suitable wall location for the chain anchors, directly behind each cooker chain, at a height
of 830mm from floor level.The distance between the two brackets should be 355mm, measured from
the centre of each bracket. (Figure 2).
2. Hold the chain anchor up to the wall where it will be required, and mark the fixing holes. (Figure 2).
3. Drill the fixing holes and fix the chain anchors to the wall using the screws provided and suitable wall
plugs for the type of wall being fixed to.
4. Leave the chains unattached until the installation process has been completed.
830mm
TO FLOOR
355mm BETWEEN BRACKETS
SCREWS
ANCHOR
BRACKET
WALL
PLUGS
FIXING
HOLES

Levelling the cooker
The cooker is equipped with adjustable feet designed for levelling the cooker
and for adjusting the upper edge of the cooker to furniture level. (Figure 3)
1. Move the cooker into its final position.
2. If the upper edge of the cooker is not at the same height as adjoining units,
use the adjustable feet to raise or lower the unit to the required height.
3. If the cooker is not level or is unstable due to an uneven floor surface, use
the adjustable feet to adjust each corner until the cooker is level. Figure 3 - Adjustable foot
Gas supply connection
PLEASE NOTE: Connection of the gas supply, adjustment, cleaning and tap servicing should ONLY
be carried out by a CORGI registered gas fitter or qualified service engineer, in accordance with the
latest regulations.
There are two installation options:
Connection to natural gas supply
The cooker comes ready for connection to a piped supply of natural gas, and should only be connected by
a CORGI registered gas fitter or qualified service personnel, in accordance with the latest regulations.
Before connecting the cooker to the gas supply system, ensure that the appliance is compatible with the
local distribution conditions (nature of the gas and gas pressure). In the event of incompatibility, consult a
CORGI registered installer to make the necessary adaptations or adjustments.
Connection to an LPG cylinder
Alternatively, the hob can be connected to an LPG cylinder. In this case, LPG injector jets (not supplied -
contact the helpline) should be fitted to the burners by the qualified service engineer. Use a rubber hose
with a safety certificate to connect the applicance to the LPG cylinder.
Every time the hob has been connected to an LPG cylinder, check the cylinder valve for soundness and the
connection of the regulator to the cylinder and also its operation.
WARNING: Under no circumstances should the gas tightness be checked by means of a naked
flame (e.g with a match or candle) as there is a danger of explosion.
WARNING: Before starting any adjustments or changing the injectors, disconnect the appliance
from gas and mains electricity supply.
Electrical connection
Once the gas supply has been connected, plug the cooker into the 3-pin socket, and switch the socket ON.
6

7
Preparation
1. Ensure that the safety chains on the rear of the cooker is attached to its anchor on the wall behind.
2. Remove the remnants of any stickers, glue and adhesive tape from all surfaces of the cooker and the
hob burners, with warm water and washing-up liquid.
3. Dry the inside and outside surfaces of the cooker with a soft lint-free cloth.
4. Ensure that all elements of the hob burners are positioned correctly.
5. Turn the grill to a moderate heat for a few minutes to burn off any dust and manufacturing resides.
6. Repeat the above process with the oven.
When using for the first time, the cooker may smell for a short time while burning off residues.
Securing the safety chains
Before securing the safety chains, check that you have completed the installation process and that all
connections have been made successfully and that the cooker is in its final operating position.
Fix the security chains to their anchor brackets:
1. Loosen the hex nut at the unattached end of the safety chain, until it is flush with the screw end. Do not
remove it completely. (Figure 4)
2. Insert the screwhead into top hole of the anchor bracket by tilting it sideways so that it is at an angle to
the top hole when it is inserted. (Figure 5)
3. When the screw head is fully engaged in the bracket, tilt it upwards so that it is straight, and tighten the
hex nut to secure the end chain link into position.
Figure 4 – loosening the hex nut Figure 5 – securing the cooker
HEX
NUT
TOP
HOLE
ANCHOR
BRACKET

8

• Never leave children unsupervised where the
cooker is installed as the appliance will get hot
during and after use.
• Never allow anyone to sit or stand on any part
of the cooker or surrounding work surface.
• Never heat up unopened food containers as
pressure can build up causing them to burst.
• Never store chemicals, food stuffs or
pressurised containers in cabinets above or
next to the cooker.
• Never use the cooker as a room heater.
• Never dry clothes or place other items on the
oven door.
• Never place flammable or plastic items on or
near the hob
• Never line any part of the oven cavity with
aluminium foil.
• Never lift the cooker using the oven door
handle.
• Make sure you understand what the cooker
controls do before using the oven.
• Always turn the cooker controls to the OFF
position when it is not in use.
• Before removing cooked food from the oven
open the door carefully to allow any heat to
disperse.
• Use dry oven gloves when removing items from
the oven.
• Be careful when operating the cooker and take
care to avoid touching hot surfaces inside the
oven and grill, and hot burners on the hob.
• Ensure that the cables of other household
appliances used near the cooker are away from
its hot elements. Ensure also that the cables
are not trapped by the oven door.
• Keep the oven door closed when the oven is
not in use.
• Keep the cooker clean as a build up of grease
or fat from cooking can cause a fire.
• Allow the cooker to cool before cleaning.
• Keep any ventilation holes clear of obstructions.
• Place pans centrally on the hob burners
Safety notes

Fire Safety
Never fill a deep fat frying pan more than 1/3 full of oil
Do not leave unattended while cooking!
In the event of a cooking pan fire:
1. Turn off the hob burners.
2. Cover the pan with a fire blanket or damp cloth.
3. Leave the pan to cool for at least an hour before you try to move it.
Never use a fire extinguisher to put out a pan fire (the force of the extinguisher could tip the pan over.)
Never use water to put out oil or fat pan fires.



Igniting the burners
Before switching on a hob burner, make sure that the selector knob you are using corresponds to the
burner you wish to switch on (Figures 6 and 7).To ignite a burner press and turn the corresponding contol
knob anti-clockwise until the high flame position is reached. Press the bottom part of the Ignition and Light
button (Figure 6) until the burner ignites.
Adjusting the flame
Adjust the flame size by turning the control knob (Figure 8). Use the appropriate level of flame for the type
of cooking you are doing and use suitably sized pans for the different burners.
The size of the flame should only be regulated within the range between and (Figure 8).
Turning off the burners
To turn off the burner, turn the control knob clockwise to the position.
Burners supplied from an LPG cylinder
Before lighting the first burner, open the valve on the LPG cylinder.Then light the burner using the method
described above.
When closing the flow of gas, before turning off the last burner close the valve on the LPG cylinder.When
the flame has gone out, close the tap of that burner.
When the hob is not in use the valve of the LPG cylinder should be closed.
9
Using the hob
Cooker controls
Before using your cooker for the first time:
Read the operating and safety instructions thoroughly.
If you have not already done so, follow the steps in the “Preparation” section on page 6 so that the cooker
is ready for use.
Figure 7 -Burner Controls Figure 8 - Hob Control Knob
1
43
2
1234
Figure 6 - Control Panel
LOW
FLAME
HIGH
FLAME
IGNITION
AND LIGHT
BUTTON
MAIN OVEN
CONTROL
KNOB
FRONT LEFT
HOB BURNER BACK LEFT
HOB BURNER FRONT RIGHT
HOB BURNER
BACK RIGHT
HOB BURNER
GRILL
CONTROL
KNOB

10
Using the grill
PLEASE NOTE:The grill and oven have a flame failure device.This ensures that no gas escapes if
the flames are extinguished. A thermal cut-off prevents the oven from overheating if the
temperature exceeds safety limits.
When grilling with the door open, fit the heat deflector (Figure 9). It may get hot in use.
The grill is located in the top oven compartment.
Turn the light on by pressing the top part of the Ignition and Light button. (Figure 11).
Turn the control knob to the large flame position (Figure 10) and press and hold the bottom half of the
Ignition and Light button until the grill burner ignites. (Figure 11).
For high heat, leave the control on the large flame position.To lower the heat level, turn the control to the
small flame position . (Figure 10).
Always use the handle when removing the grill pan (Figure 12)
When fitting the handle, hook the handle over the edge of the grill pan and through the wire rack at a
central point along the grill pan edge, (Figure 12). Lower the handle fully down to fit.
Figure 12 - Fitting the Handle
EDGE
HANDLE
WIRE RACK
Figure 10 - Grill Control Knob
Figure 9 - Heat Deflector
HEAT
DEFLECTOR
Figure 11 - Ignition and Light Button
LARGE
FLAME
SMALL
FLAME

1111
PLEASE NOTE: It is recommended to preheat the oven for a few minutes or wait until the
temperature indicator goes off before placing food in the oven for cooking.
The light can be turned on by pressing the top half of the Ignition and Light button (Figure 14)
Turn the control knob to the large flame position (Figure 13) and press and hold the bottom half of the
Ignition and Light button (Figure 14) until the oven burner ignites.
If the flame goes out, repeat all the steps above, keeping the control knob pushed in for about 5 seconds
longer.
Turn the knob to a setting from 1 to 8.The table below shows what setting you should select for the
corresponding oven temperature.
Using the main oven
G
Figure 13 - Oven / Grill Control Knob
Setting
Temp. °C
1345678
2
130 250
245
230
190
170
150140
To turn the oven OFF, turn the control knob to the position.
Figure 14 - Ignition and Light Button
LARGE
FLAME
Care of the cooker
Before removing a pan from a hob burner, reduce the flame or turn the burner off completely.
Ensure that the oven seal is always clean and free of debris.
Clean the cooker regularly to maintain its working condition and aesthetic appearance.
Do not steam pressure clean the oven.

12
Cleaning the cooker
PLEASE NOTE:The cooker must be allowed to cool down and be switched off at the mains
electricity supply before cleaning.
Clean the hob burners and the inside of the cooker after each spillage to remove cooking residues and dirt.
Hob burners and ignitors should always be kept clean and dry to ensure proper performance.
When cleaning the cooker, do not use harsh abrasives, caustic cleaners or sharp objects.Take particular
care when cleaning the knobs, control panel, and any stainless steel parts, using soft cleaners which do
not contain abrasives.
Cleaning the pan support
Remove the pan support from the hob after use. Put it in warm soapy
water for some time, then wash and dry it.
Cleaning the hob burners
Remove the caps and rings, putting them separately in warm soapy
water. After cleaning, check that the burner ports are clear (Figure 15).
The body near the injector should always be clean. Dirt accumulating
around the injector may clog it, as a result of which, the burner will not
light, or will light only with a small flame.To clean the injector use a
brush soaked in a suitable commercial solvent. (Figure 15).
Dry all the elements of the burner carefully as wet elements may not
light properly. Assemble clean and dry burners, carrying out the
disassembly steps in the reverse order.
Cleaning the oven and grill
The oven and grill compartments are coated with vitreous enamel.
To clean particularly difficult burnt spots, special oven cleaning agents may be used. However, as these
agents are caustic, be careful when using them, and follow the manufacturers guidelines.
Cleaning the glass doors
Clean the glass part of the doors with hot water and a soft cloth.Wipe the rubber seals with a soft cloth
taking care not to damage them.
Figure 15 - Cleaning the hob burners
BURNER
PORTS
INJECTOR

13
Mains lead replacement
Do not attempt to repair or replace the mains connecting cable yourself, consult a qualified
electrician.
This product is supplied with a fitted plug which contains a
3A fuse. If you are simply replacing the fuse, you must use
a 3A fuse which has been approved by ASTA to BS1362.
If the plug does not fit the socket or becomes damaged, a
new plug must be fitted. Replace the original plug with the
correct plug for your socket. If this is a 3-pin (square pin)
13A (BS1363) plug, you must make sure that it is fitted
with an ASTA approved 3A fuse. If another type of plug is
used, it must be protected by a 5A fuse, either in the plug
or at the distribution board.
1. Remove the existing fitted plug.
2. The wires in the mains lead supplied with this appliance are coloured in accordance with the following
code:
GREEN/YELLOW = EARTH (E) BLUE = NEUTRAL (N) BROWN = LIVE (L)
This product must be earthed
As the colours of the wires in the mains lead may not correspond with the colour markings identifying the
terminals in your new plug, proceed as follows.
The wire which is coloured GREEN or GREEN/YELLOW must be connected to the terminal which is
marked with the letter E or Esymbol or coloured GREEN or GREEN/YELLOW.
The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the
letter N or coloured BLACK or BLUE.
The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or
coloured RED or BROWN.
3. Ensure that the connections are tight and that no loose strands are left out of the terminals.
IF IN ANY DOUBT CONSULT A QUALIFIED ELECTRICIAN.
GREEN/
YELLOW
(EARTH)
BLUE
(NEUTRAL) BROWN
(LIVE)
FUSE
CABLE
CLAMP
Plug replacement
Figure 18 - Plug wiring
Changing the grill and oven lamps
Wait for the cooker and lamp to cool.
Unscrew and remove the diffuser.
Unscrew the lamp from the lampholder.
Replace lamp and diffuser (Figure 17).
The replacement lamp must be of the same type, voltage and wattage (15W SES 300°C).
LAMP LAMPHOLDER
DIFFUSER
Figure 17 - changing the lamp

14
For best cooking results
Oven
Grill
Hob


• Use good quality cooking pans with thick flat
bases.This gives the most efficient energy
transfer from the hob burners.
• Use pans of the correct diameter. The flame
should cover only two thirds of the pan base.
• Use pans which are large enough for the amount
of food being cooked to ensure that they do not
boil over and cause unnecessary cleaning
• Use a correctly fitting lid when boiling or stewing
to contain heat and improve boiling times.
• Never use recessed or ridged base pans.This
wastes energy and gives a longer cooking time
• Never allow flames to lick up the sides of your
pan. In this case, the pan is too small for the
burner and energy is being wasted
• Do not heat an empty pan, as this will damage
and discolour the cooking surface at the bottom
of the pan.
• For even cooking, ensure that the grill pan is
positioned centrally below the grill element. • To avoid fat splattering onto the oven interior,
ensure that the grill pan is not lined with foil and
the grill setting is not too high.
• Ensure that the oven shelf is level.This will
ensure even rising of cakes and cooking of food.
• To avoid under/overcooking, reduce or increase
cooking times and temperatures to suit personal
taste.
• Do not use pans greater than 52mm (2¼”) in
height for roasting.

15
If you are experiencing problems with your cooker, check the following problems and solutions below before
contacting the Helpline.
Troubleshooting guide
Problem Solution
Ignition does not work (on all burners). Check that:
The electric plug is in the mains socket and is
switched to ON.
Other appliances are working to determine if there
is a general power failure.
The circuit breaker in the distribution box has not
tripped.
(If the electricity supply has failed, burners may be
lit with a match.)
Pans are slow to boil or will not simmer. Check that your pans conform to the
recommendations in these instructions.
Check that the burner is dry and that spillage of
food or cleaning fluid remains are not affecting the
ignitor or burner ports.
Clean away any debris with a dry nylon brush such
as an old toothbrush. Any water on the burner
should be dried with a cloth.
Ignition does not work (one burner).

Safe cooker disposal
Customer Helpline
To help the environment, Local authority instructions should be followed for the disposal of your product
For help and assistance regarding your cooker telephone [phone].
Specification
Power supply: 230V~50Hz
Gross weight (kg): 51
External dimensions (cm): 50 width; 60 depth; 90 height
Oven capacity (litres): 42
Total Equivalent Power (kW): 11.1
Customer Service, Unit B1, Senator Point, South Boundary Road,
Knowsley, LIVERPOOL L33 7RS
HELPLINE TEL: [phone]
Monday to Friday (8.30am to 5pm)
We continuously try to improve our products for the benefit of our customers.
For this reason we reserve the right to make changes to any product at any time, without notice.
Instructions ref 26917/240108 © 2008