COP-USA MC22SDI User manual

SDI Monitor with WIFI DVR and local DVR.
MC22SDI
User’s Manual Instructions
7/17/2012

Safety Precautions:
DO NOTATTEMPT TO DISASSEMBLE THE DEVICE.
Risk of Electric Shock, Do not Open
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER NO USER-SERVICEABLE PARTS
INSIDE REFER SERVICING TO A QUALIFIED SERVICE
PERSON
This symbol is intended to alert the user to the presence of non-insulated dangerous voltage within the
product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operation and maintenance
instructions in the literature accompanying the appliance.
Warning!
1. This product has patented for configuration and appearance design, and copying is not permitted.
2. If this product fails to operate normally, contact authorized distributor or a service center. Never disassemble or modify the product in
any way. Problem caused by unauthorized user disassembly or repairs voids the warranty.
3. Electromagnetic fields in specific frequency may cause image interference.
4. Be sure to use only the standard adapter which is specified in the specification sheet. Using other adapter could cause fire, electric
shock or damage to product.
5. Connecting the power supply incorrectly may result in fire, electric shock or damage to the product as well.
6. Do not connect multiple cameras to a single adapter. Exceeding the capacity may cause abnormal heat causing fire.
7. Securely plug the power cord into power receptacle. Any loose connection may result in fire.
8. When installing the camera on a wall or ceiling, fasten it safely and securely. A falling camera may cause personal injury.
9. Do not place conductive objects (e.g. screwdrivers, coins, metal things, etc.) or containers filled with water on top of the product.
10. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause personal injury.
11. If any unusual smell or smoke comes from the unit, please stop using the product. In such case, please immediately disconnect the
power source and contact local authorized distributor or a Service Center.
12. When cleaning, do not spray water directly onto parts of the product, or may cause fire or electric shock. Gently wipe the surface with a
dry cloth. Never use detergents or chemical cleaner on the products, or may cause fire or electric shock.

Cautions
1. Do not drop objects on the products or apply strong shock to it. Keep it away from a location subject to excessive vibration or magnetic-field
interference.
2. Do not install in a location subject to high temperature (over 122°F or +50℃ ), or low temperature（below 14°F or -20℃）, it may cause fire.
3. If you want to relocate the installed products, be sure to turn off the power before moving or reinstalling it.
4. Remove the power plug from the outlet when there is a lightning storm. Neglecting to do so may cause fire or damage to the product.
5. Avoid a location which is exposed to direct sunlight, or near heat sources. Neglecting to do so may cause fire.
6. Install in a well-ventilated location.
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions for later use.
3. Pay attention that all warnings should be adhered to.
4. Follow all instruction.
5. Do not use this product near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings.
8. Do not install near any heat sources such as radiations, heat registers, or other product (including amplifiers) that produce heat.
9. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from
the apparatus.
10. Only use attachment/accessories specified by the manufacturer.
11. For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it
from the wall outlet and disconnect the antenna or cable system.
12. Refer all servicing to qualified service personnel. Servicing is required when the product has been damaged in any way, such as
power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the product has been exposed to rain or moisture,
does not operate normally, or has been dropped.
13. Do not operate the device beyond its temperature, humidity or power source ratings. Operating temperature: 14F-122F（-20℃- 50℃）;
Humidity﹤85%。

Table of Contents
Chapter 1 - Overview
1.1 Introduction
This is a user’s manual for the Camera, Monitor, DVR and WI-FI from this product.
1.2 Package
1.2.1 - SDI Monitor with DVR / WiFi DVR / SDI Camera Built-in.
1.2.2 - Remote Control for the Monitor / Remote Control for the DVR.
1.2.3 -
1.3 Specification :
1.4 Panel
1.4.1 Front：
LCD Screen、Camera、REC led、POWER led、IR led
1.4.2 Side：ON/OFF Switch
1.4.3 Back Top：Reset Button,RJ45 jack，Antenna input；
1.4.4 Back (from left to right) HDMI, VGA IN, Y, Pb, Py, VIN1, VIN1.4, V Out, Audio in 1/1.4,
1.4.5 Back Bottom：DVR SD Card, mic, mic, WiFi SD Card
1.4.6 Remote Control :
POWER：ON/OFF
MUTE：ON/OFF
PICTURE：MODE: ( USER T / STANDARD / L-LIGHT / H-LIGHT)
FREEZE：PICTURE FREEZE
INPUT：PC – N/A
HDMI – SDI CAMERA
AV – SDI CAMERA LOWER RESOLUTION
AV2 – DVR with SD CARD
YPBPr – N/A
MENU：MONITOR OSD MENU

VGA：N/A
YPbPr: N/A
HDMI: SDI CAMERA
AV ：AV
S-VIDEO：N/A
DVI：N/A
Chapter 2 - Monitor Operation
2. 1 Start
Plug the power cord,
Turn the Switch ON and the GREEN LED indicator will turn on
2.2 Menu
Monitor Screen Menu: (Picture, Sound, System, Advance, PIP)
2.2.1 Picture
ITEM
OPTIONS
CONTRAST
1-100
BRIGHTNESS
1-100
HUE
1-100
SATURATION
1-100
SHARPNESS
1-100
COLOR TONE
NORMAL/WARM/COOL
SCALE
FULL/ZOOM/ZOOM2/NORMAL/14:9
PICTURE MODE
USER/STANDARD/L-LIGHT/H-LIGHT
3D NR
OFF/LOW/MID/HIGH
MPEG NR
OFF/LOW/HIGH
2.2.2 Sound
ITEM
OPTIONS
EQUALIZER
120HZ/500HZ/1K5HZ/5KHZ/10KHZ
SOUND MODE
USER/STANDARD/MOVIE/MUSIC
SUBWOFFER
OFF/ON
SUPERBASS
OFF/ON/1/2
LOUDNESS
OFF/MODE1/MODE2/MODE3/MODE4
AVC
OFF/ON

2.2.3 System
ITEM
OPTIONS
OSD-LANGUAGE
ENGLISH/CHINESE
OSD-HPOSITION
0-100
OSD-VPOSITION
0-100
OSD-DURATION
0-100
OSD-HALFTONE
0-100
MEM-RECALL
2.2.4 Advance
ITEM
OPTIONS
SLEEP-TIMER
OFF/15M/30M/45M/60M
BLACK-L
OFF/LOW/HIGH
H-POSITION
1-100
H-CUT
0-100
V-POSITION
0-100
V-CUT
0-100
2.2.5 PIP
ITEM
OPTIONS
MULITI WINDOW
OFF/PIP/PIP FULL
SUB SOURCE
AV/AV2 (PIP/PIP FULL ON)
SIZE
LARGE/MID/SMALL (PIP ON)
PIP-POSITION
1-100 (PIP ON)
VPOSITION
1-100 (PIP ON)
BOARDERCOLOR
BLUE/BLACK
SOUNDSOURCE
MAIN/SUB
SWAP

Chapter 3 WIFI / IP DVR Operation
3.1 IP/WIFI Camera/DVR / Configuration
3.1.1 System Requirements:
- Internet Explorer 6.0 or above
- DirectX 9.0 or above
3.1.2 Client Network Settings:
Note: Your computer must be in the same network address range with the video server to communicate,
therefore you may need to change the IP address of the video server before you can login to the server. Please
follow these instructions:
Step 1: Install the Network Video Client Software
Insert the software disk to the CD-ROM, you will see the NVClient Software installation file, run the
program. After the installation, click ―Start‖ – ―Programs‖ – ―Digital Video Management Center‖ – then
run ―Server Tools V2‖ as follows
Step 2: Click search to search the video servers, choose the server and click ―Modify Net‖, a dialog will
show up as below:

Step 3: Modify the IP address (example: modify the address to 192.168.168.72), see the example
below:
3.2. Video encoder login and Interface function description
3.2.1 Login the video encoder via the NVClient software
3.2.1.1 Steps of login
Step 1: add an IP address to computer so as to access DVS/IP Camera, for example: 192.168.1.99.
Step 2: Login client side, in Windows operating system, click ―Start‖ → ―Program‖ → ―Digital Video
Management Center‖ menu, click ―NVClient‖, type user name ―admin‖, password ―admin‖ then press
―OK‖ to enter to the program.

Click on『Local Setup』on the menu bar:
Please follow the steps below to add a DVS/IPCamera into a local LAN:
Click『Search』button to locate the IP of the device.

Step 1: select the device to be added in the search list
Step 2: click on『Add』button.

Step 3: Type Local Name defined by user.『Enable auto login server』, when you login the server
next time, you won’t need to retype a username and password.
Step 4: After the setting are done, return to the main page of the software, double click the added
device in the device list, and then double click the channel below the device to see the video.
3.3 Login the video encoder via Internet Explorer
Step 1: Run the IE, type-in the IP address of the server in the address line e.g. http://192.168.168.72 as
shown below, the system will ask for permission to install the plug-in

Step 2: If this your first time to login, please click download link:
Click here to download and install theActiveX packet manually.
a dialog will pop up as below:
Step 3: Click button, a dialog will pop up as bellows:

Step 4: Click button and button to finish install.
Step 5: Input ―username‖ and ―password‖ and then click button.
Note: the default login is ―admin‖, password is ―admin‖
Step 6: Click button to open video channel.

3.4 Web client Interface function description
Click this button to open or close channel picture.
Click this button to carry out snapshot to front end video.
Click this button to enable talkback function with front end DVS/IP Camera.
Click this button to enable talkback function with front end DVS/IP Camera.
Click this button to switch between audio enable and disable.
Click this button to enable rain strip function.
Click this button to enable lighting function.
N/A for this model

N/A for this model
N/A for this model
Click this menu to switch to real time preview interface
Click this button to switch to record playback interface
Click this button to pop up parameters setting diagram
Click this button to exit login
3.5. Video Decoder login and configuration
Decoder default network parameter：
IP Address：192.168.1.[[[
Subnet mask：255.255.255.0
Default gateway：192.168.[.[
DNS server：xxx.xxx.xxx.xxx
3.5.1. Decoder login
3.5.1.1. Login steps:
Step 1: Run ―NVClient‖ in the ―Start‖‖Program‖ ―Digital Video Management Center‖ menu,
input username and password to login the system.
Step 2: Select ―Login Server‖, input username and password.

Step 3: Input the username and password (default value are admin), click ―Ok‖.
3.5.2. Decoder configuration
Enters the parameter Setting three methods：
Method 1：Select the decoder after login, select ―Setting Configuration‖ with right key
Method 2：Select the decoder after login; click the button on the main menu to pop up the remote
configuration window
Method 3：Select the decoder after login, press F5 key
3.5.2.1. Channel setting
Enters the parameter setting and select the Camera Setup, which encoder can connect the decoder in here you
to have to connect.
Step in the Setting Configuration and select the Camera Setup, then you can set which encoder the decoder
could connect.

Alone
Alone: Only connects an encoder the image. If is the multi-channel video frequency encoder may choose
the random channel decoding output also to be possible to choose an encoder all channels simultaneously to
decode the output;
Enable Auto Connect: Auto connect to encoder；
Address: input encoder domain address for the domain or the encoder IP address for the IP Add.
Port: input the decoder port
Username, Password: input the username and password for decoder login
Channel: Which channel connects the encoder. If is the multi-channel network video frequency encoder
may choose ―all channels‖, realization multi-channel video frequencies by picture division way output;
After above parameter establishment correct, then clicks on [connection] the button to connect the
corresponding encoder, if wants to separate the connection click [separation] then
Cycle
Cycle: May connect the multi-Taiwan encoder, according to establishment time-gap circulation cut
decoding output; This company's decoder are most may support 16 group circulation decoding output，Steps：

Step 1:Select『Cycle』；
Step 2:Double click『Info』（1—16）， and clicked；
Step 3:Choice Address in『Connect Info』：『Domain or IP Add』；
Step 4:Input the message『Server Add，Port，User Name，Password，Channel』of the DVS which needs
to connect;
Step 5:『Switch Times』.Input the time of the circulation show. The minimum value is 10S；
Step 6:After the above establishment completes, clicks 『Modify』;
Step 7:Continues to increase other circulation server address;
Step 8:Click『Cycle Connect』.Ok, save to FLASH.
3.6. Access camera on the WAN (INTERNET)
Step 1: Make sure the DVS IP address is LAN IP address; make sure the IP address and the DNS server
are correct and are on the same IP structure.

(Router LAN IP address)
(DVS Network Setting)
Step 2: Setting Virtual Server on the rooter

(Setting Virtual Server, Web Port: 80, add DVS IP address: 192.168.168.72)
(Setting Virtual Server, Data Port: 8200, add DVS IP address: 192.168.168.72)