HP Series v72 User manual

User’s Guide
Color Monitor Series
v72

© 2003 Hewlett-Packard Development Company, L.P.
HP, Hewlett-Packard, and the Hewlett-Packard logo are trademarks of
Hewlett-Packard Company in the U.S. and other countries/regions.
Microsoft, MS-DOS, Windows, and Windows NT are trademarks of
Microsoft Corporation in the U.S. and other countries/regions.
Intel, Pentium, Intel Inside, and Celeron are trademarks of Intel
Corporation in the U.S. and other countries/regions.
Adobe, Acrobat, and Acrobat Reader are trademarks or registered
trademarks of Adobe Systems Incorporated.
All other product names mentioned herein may be trademarks of their
respective companies.
Hewlett-Packard Company shall not be liable for technical or
editorial errors or omissions contained herein or for incidental
or consequential damages in connection with the furnishing,
performance, or use of this material. The information in this document
is provided “as is” without warranty of any kind, including, but
not limited to, the implied warranties of merchantability and fitness
for a particular purpose, and is subject to change without notice.
The warranties for HP products are set forth in the express limited
warranty statements accompanying such products. Nothing herein
should be construed as constituting an additional warranty.
THE WARRANTY TERMS CONTAINED IN THIS STATEMENT, EXCEPT
TO THE EXTENT LAWFULLY PERMITTED, DO NOT EXCLUDE,
RESTRICT OR MODIFY AND ARE IN ADDITION TO ANY
MANDATORY STATUATORY RIGHTS APPLICABLE TO THE SALE
OF THIS PRODUCT OR SERVICE TO YOU.
This document contains proprietary information that is protected
by copyright. No part of this document may be photocopied,
reproduced, or translated to another language without the prior
written consent of Hewlett-Packard Company.
ÅWARNING: Text set off in this manner indicates that failure to
follow directions could result in bodily harm or loss of life.
ÄCAUTION: Text set off in this manner indicates that failure to follow
directions could result in damage to equipment or loss of
information.

User’s Guide iii
Contents
1 Introduction
Kit Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1–1
2 Safety and Maintenance Guidelines
Safety Guidelines . . . . . . . . . . . . . . . . . . . . . . . . 2–1
Power Requirements . . . . . . . . . . . . . . . . . . . 2–1
Important Safety Information. . . . . . . . . . . . . . 2–1
Maintenance Guidelines . . . . . . . . . . . . . . . . . . . 2–2
Removing the Monitor Base . . . . . . . . . . . . . . 2–4
3 Installation
Monitor Base Installation . . . . . . . . . . . . . . . . . . . 3–1
Monitor Installation . . . . . . . . . . . . . . . . . . . . . . . 3–2
4Operation
Information Files. . . . . . . . . . . . . . . . . . . . . . . . . 4–1
Installing Drivers . . . . . . . . . . . . . . . . . . . . . . 4–2
Front Panel Controls . . . . . . . . . . . . . . . . . . . . . . 4–5
On-Screen Display . . . . . . . . . . . . . . . . . . . . . . . 4–6
On-Screen Display Functions . . . . . . . . . . . . . 4–7
Monitor Messages . . . . . . . . . . . . . . . . . . . . . . . 4–9
No Signal Message. . . . . . . . . . . . . . . . . . . . 4–9
Out of Frequency Range Message. . . . . . . . . 4–10
Using the Energy Saver Mode . . . . . . . . . . . . . . 4–11

iv User’s Guide
A Troubleshooting
Solving Common Problems . . . . . . . . . . . . . . . . . A–1
Using the World Wide Web . . . . . . . . . . . . . . . . A–4
Preparing to Call Technical Support . . . . . . . . . . . A–4
B Technical Specifications
v72 Series Monitor . . . . . . . . . . . . . . . . . . . . . . . B–1
C Agency Regulatory Notices
Federal Communications Commission Notice. . . . . C–1
Modifications . . . . . . . . . . . . . . . . . . . . . . . . C–1
Cables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . C–2
Declaration of Conformity for Products Marked
with FCC Logo, United States Only. . . . . . . . . . . . C–2
Canadian Notice . . . . . . . . . . . . . . . . . . . . . C–2
Avis Canadien . . . . . . . . . . . . . . . . . . . . . . . C–3
European Notice. . . . . . . . . . . . . . . . . . . . . . C–3
Japanese Notice . . . . . . . . . . . . . . . . . . . . . . C–3
Korean Notice . . . . . . . . . . . . . . . . . . . . . . . C–3
EPA Energy Star Compliance . . . . . . . . . . . . . C–4
Power Cord Set Requirements . . . . . . . . . . . . . . . C–4
D TCO‘99 Requirements
Environmental Requirements. . . . . . . . . . . . . . . . . D–3
Flame Retardants. . . . . . . . . . . . . . . . . . . . . . D–3
Cadmium . . . . . . . . . . . . . . . . . . . . . . . . . . . D–4
Mercury . . . . . . . . . . . . . . . . . . . . . . . . . . . . D–4
CFCs (Freons) . . . . . . . . . . . . . . . . . . . . . . . . D–4
Lead . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . D–5

User’s Guide 1–1
1
Introduction
Your microprocessor-based, digitally controlled color monitor is a
high-performance and easy-to-use product. It employs the latest
on-screen menu technology.
Kit Contents
The monitor kit contains:
■CRT monitor
■Monitor Base (pre-installed on select models)
■AC power cord (select models)
■Documentation kit

Introduction
1–2 User’s Guide

User’s Guide 2–1
2
Safety and Maintenance
Guidelines
Safety Guidelines
Power Requirements
Refer to the “Power Cord Set Requirements” on page C–4 for
information on the correct power cord set for this device.
Important Safety Information
ÅWARNING: To reduce the risk of electric shock or damage to your
equipment, do not disable the power cord grounding feature. This
equipment is designed to be connected to a grounded (earthed)
power outlet that is easily accessible to the operator. The grounding
plug is an important safety feature.
ÅWARNING: For your safety, be sure that the power outlet you plug
the power cord into is easily accessible and located as close to the
equipment as possible. When you need to disconnect the power to
the equipment, unplug the power cord from the power outlet by
grasping the plug firmly. Never pull on the cord.
ÄCAUTION: For the protection of your monitor, as well as your
computer, connect all power cords for your computer and its
peripheral devices (such as a monitor, printer, scanner) to some form
of surge protection device such as a power strip or Uninterruptible
Power Supply (UPS). Not all power strips provide surge protection;
the power strips must be specifically labeled as having this ability.
Use a power strip whose manufacturer offers a Damage
Replacement Policy so you can replace your equipment if surge
protection fails.

Safety and Maintenance Guidelines
2–2 User’s Guide
Maintenance Guidelines
To enhance the performance and extend the life of your monitor,
follow these guidelines:
■Do not open your monitor cabinet or attempt to service this
product yourself. If your monitor is not operating properly, or
has been dropped or damaged, first unplug from power outlet,
then contact your Hewlett-Packard authorized dealer, reseller,
or service provider.
■Adjust only those controls that are discussed in the operating
instructions.
■Place your monitor at least 3 inches (76 mm) away from walls
or other enclosures.
■Use only a power source and connection appropriate for this
monitor, as indicated on the label/back plate of the monitor.
■Be sure the total ampere rating of the products connected to
the outlet does not exceed the current rating of the electrical
outlet, and the total ampere rating of the products connected
to the cord does not exceed the rating of the cord. Look on the
power label to determine the ampere rating (AMPS or A) for
each device.
■Install your monitor near an outlet that you can easily reach.
Disconnect the monitor by grasping the plug firmly and pulling
it from the outlet. Never disconnect the monitor by pulling
the cord.
■Turn your monitor off when not in use. You can substantially
increase the life of your monitor by using a screen saver
program and turning off the monitor when not in use.
■Unplug your monitor from the wall outlet before cleaning. Do
not use liquid cleaners or aerosol cleaners. Use a damp cloth
for cleaning. If the screen requires additional cleaning, use an
antistatic CRT screen cleaner.
ÄCAUTION: Do not use benzene, thinner, ammonia, or any other
volatile substances to clean your monitor or the screen. These
chemicals may damage the cabinet finish as well as the screen.

Safety and Maintenance Guidelines
User’s Guide 2–3
■Slots and openings in the cabinet are provided for ventilation.
These openings must not be blocked or covered. Never push
objects of any kind into cabinet slots or other openings.
■Do not place plants on top of your monitor. Water or dirt from
the plant may get into the vents.
■Do not drop your monitor or place it on an unstable surface.
■Do not allow anything to rest on the power cord. Do not walk
on the cord.
■Keep your monitor in a well-ventilated area, away from
excessive light, heat or moisture. Keep your monitor away
from high-capacity transformers, electric motors, and other
devices with strong magnetic fields.
■In a two-monitor system, place your monitors as far apart from
one another as possible to lessen interference between them.
■Do not place the monitor face down. Damage could result to
the front panel controls or the monitor screen.

Safety and Maintenance Guidelines
2–4 User’s Guide
Removing the Monitor Base
In the event that you need to disassemble the base from the
monitor, follow these instructions:
1. If you must remove the base attachment, release the catch and
slide the base toward the back of your monitor.
2. Lift the base up and away from your monitor.

User’s Guide 3–1
3
Installation
Monitor Base Installation
On some monitors, the base must be attached prior to monitor
installation. If you need to attach the base, follow these steps:
1. Align the hooks on the base with the sockets on the bottom of
the monitor and attach the base.

Installation
3–2 User’s Guide
2. Push the base toward the front of the monitor until it stops.
Monitor Installation
Before installing your monitor, place it in a convenient,
well-ventilated location near your computer.
1. Turn off the power to your computer and other peripheral
devices.
2. Connect the video cable (blue connector) 1from the back of
the monitor to the blue 15-pin connector on the back of the
computer. Tighten the cable screws to secure the cable to the
connector.
ÄCAUTION: To avoid damaging the video cable, ensure that the
cable aligns with the 15-pin connector. Do not force the cable onto
the connector.

Installation
User’s Guide 3–3
3. Connect the power cord 2to the back of the monitor, then
connect the power cord to a power outlet.
4. Power on your computer and monitor.
If your monitor fails to function properly, refer to Appendix A,
“Troubleshooting.”
5. If necessary, adjust the front panel monitor controls according
to your personal preference. See “Front Panel Controls” on
page 4–5 for detailed information.
Your monitor installation is now complete.

Installation
3–4 User’s Guide

User’s Guide 4–1
4
Operation
Information Files
The CD-ROM included with this monitor contains two data files
that must be installed onto your computer: An .INF file and an
.ICM file.
The .INF file designates software and defines monitor resources
used by Microsoft Windows to ensure monitor compatibility with
the graphics adapter in your computer.
The .ICM file provides color matching consistency between your
monitor screen and your printer. Once installed, this file is
activated by graphics programs that have this color-matching
feature.
To install these files on your computer:
1. Insert the CD-ROM disc that came with the monitor in your
computer’s optical drive.
2. Perform the steps to install the drivers. See “Installing Drivers”
on page 4–2 and choose the steps for your operating system.
3. To get the latest .INF and .ICM files, download them from the
HP Web site. Access http://www.hp.com and follow the links
to the Support page for monitors to download the appropriate
files.

Operation
4–2 User’s Guide
Installing Drivers
The HP monitor comes with driver software allowing you to take
advantage of the Plug and Play feature of the Windows Me,
Windows 2000, or Windows XP operating system. This software
enables the computer to communicate with the monitor and use all
the monitor features.
HP computers may come with the Plug and Play drivers
pre-installed. If you have an older computer, these drivers may not
be pre-installed and you may need to install the drivers from the
CD-ROM disc that came with the monitor.
If the installation procedure for the operating system is different, or
if you need more detailed installation information, please refer to
the Microsoft Windows information that came with the computer.
Windows 2000 users
The procedure for installing the driver for your operating system
may vary.
To install the driver for the v72 monitor:
1. Click Start, select Settings, and then click Control Panel.
2. Double-click Display.
3. Click the Settings tab.
4. Click Advanced Properties or Advanced, and select the
Monitor tab.
5. Click Properties.
6. Click the Driver tab.
7. Click Update Driver and click Next.
8. Select the recommended option, and then click Next.
9. Select the Specify a Location box.
10. Find and open the hp_v72.inf file on the CD-ROM disc in the
Drivers directory, and click OK.
11. Click Next to install the monitor driver.

Operation
User’s Guide 4–3
Windows Me users
The procedure for installing the driver for your operating system
may vary.
To install the driver for the v72 monitor:
1. Click Start, select Settings, and then click Control Panel.
2. Double-click Display.
3. Click the Settings tab.
4. Click the Advanced button.
5. Select the Monitor tab.
6. Click the Change button.
7. Select the Specify the location of the driver box, and
then click Next.
8. Find and open the hp_v72.inf file on the CD-ROM disc in the
Drivers directory, and click OK.
9. Click Next to install the monitor driver.
Windows XP users
The procedure for installing the driver for your operating system
may vary.
To install the driver for the v72 monitor:
1. Click Start.
2. Click Control Panel.
3. Click Appearance and Themes.
4. Click Display.
5. Select the Settings tab.
6. Click the Advanced button.
7. Select the Monitor tab.

Operation
4–4 User’s Guide
8. Click Properties.
9. Select the Driver tab.
10. Click Update Driver.
11. Select the Install from a list or specific location box,
and then click Next.
12. Select the Don’t search box, and then click Next.
13. Click Have Disk.
14. Click Browse.
15. Find and open the hp_v72.inf file on the CD-ROM disc in the
Drivers directory, and click OK.
16. Click Next to install the monitor driver.
If the installation procedure of the monitor driver for the Windows
2000, Windows Me, or Windows XP operating system is different,
or if you need more detailed installation information, refer to the
Microsoft Windows information that came with the PC.

Operation
User’s Guide 4–5
Front Panel Controls
Front Panel Controls
Item Icon Name Function
1
Select Launches on-screen displays,
selects functions and
adjustments, and exits menus
and On-Screen Display.
2
Left Adjustment Moves backward through menu
options or decreases
adjustment levels.
3
Right Adjustment Moves forward through menu
options or increases adjustment
levels.
4
Power/LED Controls power to the monitor.
The LED on the power button
indicates the state of the
monitor.

Operation
4–6 User’s Guide
On-Screen Display
The On-Screen Display (OSD) adjusts the screen image based on
your viewing preferences. To access the OSD, do the following:
1. If the monitor is not already on, press the Power button to turn
on the monitor.
2. Press the Select button to display the On-Screen Display menu.
A screen similar to this one appears. For a description of the
icons that appear on the screen, see “On-Screen Display
Functions” on page 4–7.
3. To move to a function, press the Right-Adjustment or
Left-Adjustment button on the front panel of your monitor until
the function is highlighted.
4. Press the Select button on the monitor choose the function.
5. The adjustment window displays. Press the Right-Adjustment or
Left-Adjustment buttons to increase (Right) or decrease (Left) the
level of adjustment.
6. Press Select to save the new adjustment.
7. To exit the On-Screen Display, select the Exit icon and press
the Select button once.