Steelcase 8824RCT User manual

Steelcase, Inc.
Grand Rapids, MI 49501
U.S.A.
1-888-783-3522
Radius Computer Table
Models: 8824RCT 8836RCT 8830RCT
NOTE: Care should be taken to avoid scratching or marring painted surfaces!
Tools
Assembly Directions Printed In U.S.A.
REV
93-9501353 A
Page 1 of 7
#2 and #3 Phillips

Assembly Directions
93-9501353 REV A Page 2 of 7
Stand center back panel assembly on end in an inverted position, and secure right and left hand back panel
assemblies onto each side with (4) screws.
NOTE: Make sure panel assemblies are placed tight against each other without gaps, prior to tightening screws!
1.
NO SPACE SHOULD APPEAR AFTER ASSEMBLY
10 X 7/8” WOOD
SCREW (4) EACH SIDE
Position center wire tray between left and right hand back panel
assemblies. Secure center wire tray to center back panel
assembly with (4) screws. Secure center wire tray to each back
panel assembly with (1) sheet metal screw on each side.
2.
10 X 7/8” WOOD SCREW
10 X 3/8” SHEET METAL
SCREW (1) EACH SIDE

Assembly Directions
93-9501353 REV A Page 3 of 7
The center back panel includes (3) sets of (2) holes for attaching the bracket back panel attachment.
Determine the height of your worksurface. The worksurface may be assembled at (3) different heights, (26”,
28”, and 30” high). Locate the set of holes for your heights. Secure bracket back panel attachment to center
back assembly with (3) machine screws.
NOTE: Start all machine screws with fingers and continue tightening with power driver, thus spreading flanges on brass inserts located in
center back panel.
3.
26” HIGH WORKSURFACE
28” HIGH WORKSURFACE
30” HIGH WORKSURFACE
1/4-20 X 1/2” MACHINE
SCREW (3) REQUIRED

Assembly Directions
93-9501353 REV A Page 4 of 7
Each end panel assembly includes (3) sets of (2) holes for attaching worksurface brackets. The holes must
match up with the same set of holes used in Step 3. Attach worksurface brackets to end panel assemblies
with (2) machine screws each.
NOTE: Start all machine screws with fingers and continue tightening with power driver, thus spreading flanges on brass inserts located in
end panel assembly.
When worksurfaces are assembled at 26” or 28” heights, it would ease assembly if a spacer (not included)
was placed under worksurface thus elevating bracket attaching holes with holes in end panel assembly.
NOTE: It may be necessary to loosen screws, and adjust brackets on underside of worksurface for proper fit to end panel assembly.
Tighten all screws.
4.
26” HIGH WORKSURFACE
28” HIGH WORKSURFACE
30” HIGH WORKSURFACE
1/4-20 X 1/2” MACHINE
SCREWS (2) PER END

Assembly Directions
93-9501353 REV A Page 5 of 7
Position and secure right and left hand back panel assemblies to right and left hand end panel assemblies
with (3) machine screws each.
NOTE: Start all machine screws with fingers and continue tightening with power driver, thus spreading flanges on brass
inserts located in each end panel assembly.
Secure bracket back panel attachment to worksurface with (3) wood screws.
5.
10 X 7/8” WOOD SCREW
(3) REQUIRED
1/4-20 X 1/2” MACHINE
SCREW (3) PER END

Assembly Directions
93-9501353 REV A Page 6 of 7
Position and secure right and left hand modesty panels to right and left hand end panel assemblies with (1)
machine screw.
NOTE: Start all machine screws with fingers and continue tightening with power driver, thus spreading flanges on brass inserts located in
center back panel.
Align holes in modesty panel with pre-drilled holes in bottom of worksurface and secure with (4) wood screws
each panel.
6.
10 X 7/8” WOOD SCREW (4)
REQUIRED EACH PANEL
1/4-20 X 1/2” MACHINE SCREW

Assembly Directions
93-9501353 REV A Page 7 of 7
Remove center modesty panel from stored position in center wire tray, and insert between right and left hand
modesty panel in the manner shown below. Secure center modesty panel to right and left hand modesty
panels with (2) sheet metal screws. Align (2) holes in center modesty panel flange with (2) pre-drilled holes in
underside of worksurface and secure with (2) wood screws.
NOTE: Make sure all screws are tight, carefully turn unit upright and adjust glides.
7.
10 X 7/8”
WOOD
SCREW
10 X 3/8” SHEET METAL
SCREW