Teknik 5423505 User manual

www.teknikoffice.co.uk
Iron Foundry Desk
Model 5423505
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
For all your
newfangled gadgetry.
Teknik

Table of Contents Assembly Tools Required
2
3
4-8
9-10
11-12
13-14
15
Hardware Identification
Part Identification
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Skip the power trip.
This time.
Page 2 www.sauder.com 423505
Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
BLACK 3/8" MACHINE SCREW - 6
4
LEVELER - 6
1BLACK 1-3/4" MACHINE SCREW - 2 2
BLACK 1-7/16" TAPERED MACHINE SCREW - 14
3
BLACK 1/2" PAN HEAD SCREW - 4
5

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
A RIGHT END (1)
B LEFT END (1)
C UPRIGHT (1)
D TOP (1)
E SHELF (2)
G UPPER BRACE (1)
H CROSS BRACE (1)
J LOWER TUBE (1)
K LOWER BRACE (1)
Now you know
our ABCs.
Page 3
A
B
C
D
E
E
G
H
J
K

Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å NOTE: Do not completely tighten the SCREWS in this step.
å Fasten the BRACES (G and K) to the UPRIGHT (C). Use three
BLACK 3/8" MACHINE SCREWS (4).
å Fasten the LEFT END (B) to the BRACES (G and K). Use three
BLACK 3/8" MACHINE SCREWS (4).
å Fasten the LOWER TUBE (J) to the LEFT END (B) and
UPRIGHT (C). Use two BLACK 1-3/4" MACHINE SCREWS (2).
Page 4
B
C
G
J
K
G
K
C
BLACK 1-3/4" MACHINE SCREW
(2 used for the LOWER TUBE)
2
BLACK 3/8" MACHINE SCREW
(6 used for BRACES)
4

å NOTE: Do not completely tighten the SCREWS in this step.
å Fasten the TOP (D) to the ENDS (A and B) and UPRIGHT (C). Use
six BLACK 1-7/16" TAPERED MACHINE SCREWS (3).
Step 2
Page 5
These holes
must be here.
For support, place packing
foam and magazines here.
A
D
B
C
Just think. The sooner
you do this, the sooner
you do something else.
BLACK 1-7/16" TAPERED MACHINE SCREW
(6 used for the TOP)
3

Step 3
å Fasten the SHELVES (E) to the RIGHT END (A) and
UPRIGHT (C). Use eight BLACK 1-7/16" TAPERED
MACHINE SCREWS (3).
å Completely tighten all of the SCREWS in the metal frame.
Page 6
A
C
E
E
BLACK 1-7/16" TAPERED MACHINE SCREW
(8 used for the SHELVES)
3

å Fasten the CROSS BRACE (H) to the RIGHT END (A) and
UPRIGHT (C). Use four BLACK 1/2" PAN HEAD SCREWS (5).
å Turn six LEVELERS (1) into the bottom edges of the ENDS (A
and B) and UPRIGHT (C).
Step 4
Page 7
A
C
H
B
1
If you're doing this to
help a friend, don't
leave without a bite.
The smooth head of
the rivet should face up.
BLACK 1/2" PAN HEAD SCREW
(4 used for the CROSS BRACE)
5

Step 5
å Carefully stand your unit upright.
å To level your unit, turn the LEVELERS.
å NOTE: Please read the back pages of the instruction booklet for important safety information.
å This completes assembly. Clean with a damp cloth. Wipe dry.
Page 8
50 lbs.
25 lbs.
25 lbs.
If needed, turn the
LEVELERS to level your unit.

Page 13
WARNING
Please use your furniture correctly and safely. Improper use can cause safety hazards,
or damage to your furniture or household items. Carefully read the following chart.
Look out for: What can happen: How to avoid the problem:
• Overloaded shelves or drawers.
• Improper loading can cause the product
to be top-heavy.
• Risk of injury.
• Top-heavy furniture can tip over.
• Overloaded shelves and drawers can
break.
• Never exceed the weight limits shown in
the instructions.
• Work from bottom to top when loading
shelves and drawers. Place the heavier
items on the lower shelves or in lower
drawers.
• Improperly moving furniture that is not
designed and equipped with casters. • Furniture can tip over or break if improperly moved.
• Physical injury. Furniture can be very
heavy.
• Breakage of tops - particularly with
double pedestal furniture (drawers at both
ends).
• Unload shelves and drawers from top to
bottom before moving the unit.
• Do not push furniture, especially on a
carpeted floor. Have a friend help you lift
the item and set it in place.
• Provide support to the center section of
the top when lifting the furniture.
• Placing TVs on furniture items that are
not designed to support a television is
hazardous.
• Risk of injury or death. TVs can be very
heavy. Plus the weight and location of the
picture tube tends to make TVs unbalanced
and prone to tipping forward.
• This product is not designed to support a
television.