Coral Box AquaLink A1 User manual

Coral Box AquaLink A1
Quick Start Guide
Packing list
AQlink A1 main unit
X1
Quick Start Guide(this document)
X1
Features
Direct drive Jebao/Jecod DCT/DCS/DCP-series pumps, CP series
cross-flow pumps and compatible 3 phases pump/wave makers.
High performance fast response with sinusoidal current drive, offer
minimized rotor vibration and extra quiet operation.
Pump Selection : Up to 32 preset pump parameters.
Control Input : On-board RJ45 socket, using one analog channel can control
rotational speed, two analog channel can control clockwise and
counter-clockwise direction.
Continuous firmware upgrade to support new pumps, please contact your
sales for arrangement.
Specification
DC IN:12 – 24VDC adapter or Pump Extender, current up to 4A.
Control Voltage: 0 – 10VDC, 2 channels via RJ45 8P connection.
Pump Output: 24V 3 phases BLDC pump and wave maker.
Size and weight : Typical 10cm x 10cm x 2.7cm (W*L*H), 150g.
Suitable for:
DCA
2000
3000
6000
9000
DCS
2000
3000
4000
7000
9000
12000
DCP
3000
4000
5000
6500
8000
10000
DCT
3000
4000
6000
8000
12000
15000
CP
CP-25
CP-90
CP-40
CP-120
GF
150
DCW
4000
6000
9000
12000
DCQ
4000
6000
9000
12000
QP
QP-5
QP-9
QP-16
Reversed
Quick Start
1. Setting of Programming Switch: On the side of the
main unit there is a programming switch (Fig.1) with 5
slide levers, please refer to Fig.4, find your pump’s
model and set the slide levers accordingly. Please visit
www.coral-box.com for latest support list.
2. Connection to Variable Speed Control Unit : Use a
RJ45 cable to connect to the main unit’s RJ45 8P
socket. The pin definition of the RJ45 socket is as on
Fig.2. They are 0 - 10V DC input, applying voltage out
of this range will damage the unit permanently. CH1
1-10V corresponding to 10 -100%, and CH2 having no
connection or lesser than 2V DC, the pump will be in
default/clockwise direction, else if voltage of more
than 8VDC, the pump will rotates reversely.
3. Connection to Your Aquarium Pump: As on Fig.3, connect your pump to the
AQLink A1 “PUMP” cable.

4. Connection to Power Supply: Power off your
original pump/ wave maker DC adapter, and then
connect to AQLink A1 DC jack input, the jack polarity
is as below:
5. Finally, switch on the input power of the DC
adapter, the green LED will light up indicating the unit
start to operate normally.
(Fig.4 Programming Switch Setting for Supported Pumps sample)
1
DCA2000
DCS2000
2
DCA3000
DCS3000
DCA3000
DCT3000
3
DCP3000
4
DCS4000
DCT4000
5
DCP4000
6
DCP5000
7
DCA6000
DCW6000
DCS6000
DCQ6000
8
DCP6500
9
DCS7000
10
DCP8000
DCT8000
11
DCS9000
12
DCP10000
13
DCS12000
DCT12000
14
DCT15000
15
CP-25
CP-90
16
CP-40
CP-120
17
QP-9
18
QP-16
19
Reversed
20
GF150
Warning
Precaution – Controller Installation
Please install the controller AWAY from wet, high humidity
and hotenvironment,excessivehumidityand high temperature
operating environment may
DAMAGE THE CONTROLLER PERMANENTLY
Pleaseinstallinanenvironmentwithgoodventilation.This is to
allow the internal electronics working at the desired temperature
and operating environment, or else product durability will be
affected. Active ventilation is required when the operating
temperature is high
All right Reserved – No part or whole of this Manual can be reproduced without written
authorization by Coral-Box.com